| Age | Commit message (Collapse) | Author |
|---|
|
md/bitmap tracks how many active write requests are pending on blocks
associated with each bit in the bitmap, so that it knows when it can clear
the bit (when count hits zero).
The counter has 14 bits of space, so if there are ever more than 16383, we
cannot cope.
Currently the code just calles BUG_ON as "all" drivers have request queue
limits much smaller than this.
However is seems that some don't. Apparently some multipath configurations
can allow more than 16383 concurrent write requests.
So, in this unlikely situation, instead of calling BUG_ON we now wait
for the count to drop down a bit. This requires a new wait_queue_head,
some waiting code, and a wakeup call.
Tested by limiting the counter to 20 instead of 16383 (writes go a lot slower
in that case...).
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a bypass-the-cache read fails, we simply try again through the cache. If
it fails again it will trigger normal recovery precedures.
update 1:
From: NeilBrown <neilb@suse.de>
1/
chunk_aligned_read and retry_aligned_read assume that
data_disks == raid_disks - 1
which is not true for raid6.
So when an aligned read request bypasses the cache, we can get the wrong data.
2/ The cloned bio is being used-after-free in raid5_align_endio
(to test BIO_UPTODATE).
3/ We forgot to add rdev->data_offset when submitting
a bio for aligned-read
4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
so we need to invalidate the segment counts.
5/ We don't de-reference the rdev when the read completes.
This means we need to record the rdev to so it is still
available in the end_io routine. Fortunately
bi_next in the original bio is unused at this point so
we can stuff it in there.
6/ We leak a cloned bio if the target rdev is not usable.
From: NeilBrown <neilb@suse.de>
update 2:
1/ When aligned requests fail (read error) they need to be retried
via the normal method (stripe cache). As we cannot be sure that
we can process a single read in one go (we may not be able to
allocate all the stripes needed) we store a bio-being-retried
and a list of bioes-that-still-need-to-be-retried.
When find a bio that needs to be retried, we should add it to
the list, not to single-bio...
2/ We were never incrementing 'scnt' when resubmitting failed
aligned requests.
[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
And a couple of bug fixes found by sparse.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Includes a couple of bugfixes found by sparse.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Once upon a time we needed to fixed limit to the number of md devices,
probably because we preallocated some array. This need no longer exists, but
we still have an arbitrary limit.
So remove MAX_MD_DEVS and allow as many devices as we can fit into the 'minor'
part of a device number.
Also remove some useless noise at init time (which reports MAX_MD_DEVS) and
remove MD_THREAD_NAME_MAX which hasn't been used for a while.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It is equivalent to conf->raid_disks - conf->mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add a new sysfs interface that allows the bitmap of an array to be dirtied.
The interface is write-only, and is used as follows:
echo "1000" > /sys/block/md2/md/bitmap
(dirty the bit for chunk 1000 [offset 0] in the in-memory and on-disk
bitmaps of array md2)
echo "1000-2000" > /sys/block/md1/md/bitmap
(dirty the bits for chunks 1000-2000 in md1's bitmap)
This is useful, for example, in cluster environments where you may need to
combine two disjoint bitmaps into one (following a server failure, after a
secondary server has taken over the array). By combining the bitmaps on
the two servers, a full resync can be avoided (This was discussed on the
list back on March 18, 2005, "[PATCH 1/2] md bitmap bug fixes" thread).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It isn't needed as mddev->degraded contains equivalent info.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
They are not needed. conf->failed_disks is the same as mddev->degraded and
conf->working_disks is conf->raid_disks - mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch contains the scheduled removal of the START_ARRAY ioctl for md.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://git.infradead.org/hdrinstall-2.6:
Remove export of include/linux/isdn/tpam.h
Remove <linux/i2c-id.h> and <linux/i2c-algo-ite.h> from userspace export
Restrict headers exported to userspace for SPARC and SPARC64
Add empty Kbuild files for 'make headers_install' in remaining arches.
Add Kbuild file for Alpha 'make headers_install'
Add Kbuild file for SPARC 'make headers_install'
Add Kbuild file for IA64 'make headers_install'
Add Kbuild file for S390 'make headers_install'
Add Kbuild file for i386 'make headers_install'
Add Kbuild file for x86_64 'make headers_install'
Add Kbuild file for PowerPC 'make headers_install'
Add generic Kbuild files for 'make headers_install'
Basic implementation of 'make headers_check'
Basic implementation of 'make headers_install'
|
|
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out. I don't believe this is a supportable
approach.
This patch changes the approach to use the same approach as swap files. i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.
swapfile only uses parts of the file that provide a full pages at contiguous
addresses. We don't have that luxury so we have to cope with pages that are
non-contiguous in storage. To handle this we attach buffers to each page, and
store the addresses in those buffers.
With this approach the pagecache may contain data which is inconsistent with
what is on disk. To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file. If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used. And new version of mdadm will have support for this.
This approach simplifies a lot of code:
- we no longer need to keep a list of pages which we need to wait for,
as the b_endio function can keep track of how many outstanding
writes there are. This saves a mempool.
- -EAGAIN returns from write_page are no longer possible (not sure if
they ever were actually).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
md/bitmap currently has a separate thread to wait for writes to the bitmap
file to complete (as we cannot get a callback on that action).
However this isn't needed as bitmap_unplug is called from process context and
waits for the writeback thread to do it's work. The same result can be
achieved by doing the waiting directly in bitmap_unplug.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes. e.g.
A B C D
D A B C
E F G H
H E F G
(columns are drives, rows are stripes, LETTERS are chunks of data).
This is similar to raid10's 'far' mode, but not quite the same. So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This adds the Kbuild files listing the files which are to be installed by
the 'headers_install' make target, in generic directories.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
reshape_position is a 64bit field that was not 64bit aligned. So swap with
new_level.
NOTE: this is a user-visible change. However:
- The bad code has not appeared in a released kernel
- This code is still marked 'experimental'
- This only affects version-1 superblock, which are not in wide use
- These field are only used (rather than simply reported) by user-space
tools in extemely rare circumstances : after a reshape crashes in the
first second of the reshape process.
So I believe that, at this stage, the change is safe. Especially if people
heed the 'help' message on use mdadm-2.4.1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
... being careful that mutex_trylock is inverted wrt down_trylock
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Instead of checkpointing at each stripe, only checkpoint when a new write
would overwrite uncheckpointed data. Block any write to the uncheckpointed
area. Arbitrarily checkpoint at least every 3Meg.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to. The geometry allows for changing
chunksize, layout and level as well as number of devices.
When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array. For version-1, we use a feature bit for the same effect.
When starting an array we check for an incomplete reshape and restart the
reshape process if needed. If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds raid5_reshape and end_reshape which will start and finish the
reshape processes.
raid5_reshape is only enabled in CONFIG_MD_RAID5_RESHAPE is set, to discourage
accidental use.
Read the 'help' for the CONFIG_MD_RAID5_RESHAPE entry.
and Make sure that you have backups, just in case.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch provides the core of the resize/expand process.
sync_request notices if a 'reshape' is happening and acts accordingly.
It allocated new stripe_heads for the next chunk-wide-stripe in the target
geometry, marking them STRIPE_EXPANDING.
Then it finds which stripe heads in the old geometry can provide data needed
by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to
read all blocks on those stripes.
Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are
needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a
STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then
is written out and released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
expanding
We need to allow that different stripes are of different effective sizes, and
use the appropriate size. Also, when a stripe is being expanded, we must
block any IO attempts until the stripe is stable again.
Key elements in this change are:
- each stripe_head gets a 'disk' field which is part of the key,
thus there can sometimes be two stripe heads of the same area of
the array, but covering different numbers of devices. One of these
will be marked STRIPE_EXPANDING and so won't accept new requests.
- conf->expand_progress tracks how the expansion is progressing and
is used to determine whether the target part of the array has been
expanded yet or not.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache
data structure.
This requires allocating new stripes in a new kmem_cache. If this succeeds,
we copy cache pages over and release the old stripes and kmem_cache.
We then allocate new pages. If that fails, we leave the stripe cache at it's
new size. It isn't worth the effort to shrink it back again.
Unfortuanately this means we need two kmem_cache names as we, for a short
period of time, we have two kmem_caches. So they are raid5/%s and
raid5/%s-alt
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
grow
The remainder of this batch implements raid5 reshaping. Currently the only
shape change that is supported is added a device, but it is envisioned that
changing the chunksize and layout will also be supported, as well as changing
the level (e.g. 1->5, 5->6).
The reshape process naturally has to move all of the data in the array, and so
should be used with caution. It is believed to work, and some testing does
support this, but wider testing would be great for increasing my confidence.
You will need a version of mdadm newer than 2.3.1 to make use of raid5 growth.
This is because mdadm need to take a copy of a 'critical section' at the
start of the array incase there is a crash at an awkward moment. On restart,
mdadm will restore the critical section and allow reshape to continue.
I hope to release a 2.4-pre by early next week - it still needs a little more
polishing.
This patch:
Previously the array of disk information was included in the raid5 'conf'
structure which was allocated to an appropriate size. This makes it awkward
to change the size of that array. So we split it off into a separate
kmalloced array which will require a little extra indexing, but is much easier
to grow.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Both R1BIO_Barrier and R1BIO_Returned are 4 !!!!
This means that barrier requests don't get returned (i.e. b_endio called)
because it looks like they already have been.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Also export current (average) speed and status in sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
.. because they aren't used outside md.c
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
md sometimes call put_page on NULL pointers (treating it like kfree). This is
not safe, so define and use a 'safe_put_page' which checks for NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).
These personalities have fairly artificial 'numbers'. The numbers
are use to:
1- provide an index into an array where the various personalities
are recorded
2- identify the module (via an alias) which implements are particular
personality.
Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely). Module identification can be done using an alias
based on level rather than 'personality' number.
The current 'raid5' modules support two level (4 and 5) but only one
personality. This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.
With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.
This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- replace open-coded hash chain with hlist macros
- Fix hash-table size at one page - it is already quite generous, so there
will never be a need to use multiple pages, so no need for __get_free_pages
No functional change.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add in correct read-error handling for resync and read-only situations.
When read-only, we don't over-write, so we need to mark the failed drive in
the r10_bio so we don't re-try it. During resync, we always read all blocks,
so if there is a read error, we simply over-write it with the good block that
we found (assuming we found one).
Note that the recovery case still isn't handled in an interesting way. There
is nothing useful to do for the 2-copies case. If there are 3 or more copies,
then we could try reading from one of the non-missing copies, but this is a
bit complicated and very rarely would be used, so I'm leaving it for now.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Largely just a cross-port from raid1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There is this "FIXME" comment with a typo in it!! that been annoying me for
days, so I just had to remove it.
conf->disks[i].rdev should only be accessed if
- we know we hold a reference or
- the mddev->reconfig_sem is down or
- we have a rcu_readlock
handle_stripe was referencing rdev in three places without any of these. For
the first two, get an rcu_readlock. For the last, the same access
(md_sync_acct call) is made a little later after the rdev has been claimed
under and rcu_readlock, if R5_Syncio is set. So just use that access...
However R5_Syncio isn't really needed as the 'syncing' variable contains the
same information. So use that instead.
Issues, comment, and fix are identical in raid5 and raid6.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
