| Age | Commit message (Collapse) | Author |
|---|
|
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
Switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
and make ide_wait_cmd() static.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests. Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set. Also,
ide_dma_intr() is modified to use task_end_request().
Enables TASKFILE ioctls to get valid register outputs on
successful completion.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.
* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.
* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit. It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().
This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
(including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
x86 machines using user-space solutions or dm-byteswap should result in
much better performance because DMA can be used)
For previous discussions please see:
http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.html
http://lkml.org/lkml/2004/2/28/111
[ I have dm-byteswap device mapper target if somebody is interested
(patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix build break of powerpc holly_defconfig:
In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
There's no need to have a sized array in the prototype, might as well
turn it into a pointer.
It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename ide_device_add() to ide_device_add_all() and make it accept
'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.
* Add ide_device_add() wrapper for ide_device_add_all().
* Convert ide_generic_init() to use ide_device_add_all().
* Remove no longer needed ideprobe_init().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (31 commits)
ocfs2: clean up bh null checks
ocfs2: document access rules for blocked_lock_list
configfs: file.c fix possible recursive locking
configfs: dir.c fix possible recursive locking
configfs: Remove EXPERIMENTAL
ocfs2: bump version number
ocfs2/dlm: Clear joining_node on hearbeat node down
ocfs2: convert byte order of constant instead of variable
ocfs2: Update default cluster timeouts
ocfs2: printf fixes
ocfs2: Use generic_file_llseek
ocfs2: Safer read_inline_data()
ocfs2: Silence false lockdep warnings
[PATCH 2/2] ocfs2: cluster aware flock()
[PATCH 1/2] ocfs2: add flock lock type
ocfs2: Local alloc window size changeable via mount option
ocfs2: Support commit= mount option
ocfs2: Add missing permission checks
[PATCH 2/2] ocfs2: Implement group add for online resize
[PATCH 1/2] ocfs2: Add group extend for online resize
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
fix drivers/ata/sata_fsl.c double-decl
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: Merge winbond support
ata_generic: Cenatek support
pata_winbond: error return
pata_serverworks: Fix cable types and cosmetics
pata_mpc52xx: remove un-needed assignment
libata: fix off-by-one in error categorization
ahci: factor out AHCI enabling and enable AHCI before reading CAP
ata_piix: implement SIDPR SCR access
ata_piix: convert to prepare - activate initialization
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: resychronize with upstream changes and resubmit
[libata] pata_legacy: typo fix
[libata] pata_winbond: update for new ->data_xfer hook
pata_pcmcia: convert to new data_xfer prototype
libata annotations and fixes
libata: use dev_driver_string() instead of "libata" in libata-sff.c
ata_piix: kill unused constants and flags
...
|
|
This allows others to use the DLM constants without being tied to the
function API of fs/dlm.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (509 commits)
V4L/DVB (7078): radio: fix sf16fmi section mismatch
V4L/DVB (7077): bt878: remove handcrafted PCI subsystem ID check
V4L/DVB (7075): Make a local function static
V4L/DVB (7074): DiB7000P: correct tuning problem for 7MHz channel
V4L/DVB (7073): DiB7070: Reception quality improved
V4L/DVB (7072): sets the MT2060 IF1 frequency according to EEPROM
V4L/DVB (7071): DiB0700: Start streaming the right way
V4L/DVB (7070): Fix some tuning problems
V4L/DVB (7069): Support for myTV.t
V4L/DVB (7068): Add support for WinTV Nova-T-CE driver
V4L/DVB (7067): fix autoserach in the Hauppauge NOVA-T 500
V4L/DVB (7066): ASUS My Cinema U3000 Mini DVBT Tuner
V4L/DVB (7065): Artec T14BR patches
V4L/DVB (7063): xc5000: Fix OOPS caused by missing firmware
V4L/DVB (7062): radio-si570x: Some fixes and new USB ID addition
V4L/DVB (7061): radio-si470x: Some cleanups
V4L/DVB (7060): em28xx: remove has_tuner
V4L/DVB (7059): cx88: Ensure the tuner is reset correctly
V4L/DVB (7058): IR corrections for the Pinnacle 800i
V4L/DVB (7056): tuner: suppress obsolete tuner i2c address warning for XC5000 tuners
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (67 commits)
ide: remove redundant DMA blacklist check from __ide_dma_on()
ide: cleanup ide_set_dma()
ide: remove redundant ->ide_dma_on call from set_using_dma()
sc1200: move DMA timings to timing tables
ide: add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag
sis5513: factor out UDMA programming code
pdc202xx_new: move PIO programming code to pdcnew_set_pio_mode()
ide: make 'extra' field in struct ide_port_info u8
ide: kill duplicate code in ide_dump_{ata,atapi}_status()
ide-disk: use ide_get_lba_addr()
ide: printk fix
ide: add ide_tf_read() helper
ide: fix registers loading order in ide_dump_ata_status()
ide-disk: use do_rw_taskfile() (take 2)
ide-disk: add ide_tf_set_cmd() helper
ide-disk: extend timeout for PIO-in commands
ide: remove 'handler' field from ide_task_t (take 2)
ide: use ->data_phase to set ->handler in do_rw_taskfile()
ide: convert do_rw_taskfile() to use ->data_phase
ide: merge flagged_taskfile() into do_rw_taskfile()
...
|
|
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The maximum value used currently for 'extra' field in struct ide_port_info
is 240.
Make 'extra' u8 so it packs nicely together with enablebits[] and 'chipset'
fields (ide_pci_enablebit_t is 3 bytes and hwif_chipset_t is 1 byte).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Export ide_get_lba_addr().
* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().
* Remove incorrect comment from idedisk_read_native_max_address()
(noticed by Sergei).
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out code reading taskfile registers from ide_end_drive_cmd()
to the new ide_tf_read() helper.
* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
particular IDE taskfile register in ide_tf_read().
* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.
* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.
* Factor out code getting sector address from ide_dump_ata_status()
to the new ide_dump_sector() function.
* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().
* Remove no longer needed ide_read_24().
The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_DMA_PIO_FALLBACK taskfile flag to indicate the need
to skip loading taskfile registers in do_rw_taskfile().
* Export do_rw_taskfile().
* Convert __ide_do_rw_disk() to use do_rw_taskfile().
* Unexport ide_tf_load().
* Unexport {pre_task_out,task_in}_intr() and make it static.
* Remove incorrect comment about do_rw_taskfile() from <linux/ide.h>.
There should be no functionality changes caused by this patch.
v2:
* Add missing blk_fs_request() check to task_dma_ok() (for VDMA).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
which require custom handlers. Check the flag in do_rw_taskfile() and set
handler accordingly.
* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
ide_tf_set_{specify,restore,setmult}_cmd().
* Make {set_geometry,recal,set_multmode}_intr() static.
* Remove no longer needed 'handler' field from ide_task_t.
v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ->data_phase to set ->handler in do_rw_taskfile() instead of
setting ->handler in callers of ide_raw_taskfile()/do_rw_taskfile().
* Unexport task_no_data_intr() and make it static.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use task->data_phase in do_rw_taskfile() to decide what to do.
* task->prehandler is only used by TASKFILE[_MULTI]_OUT so just
use pre_task_out_intr() directly and remove no longer needed
'prehandler' field from ide_task_t.
* Remove no longer needed ide_pre_handler_t type.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
task->data_phase == TASKFILE_MULTI_{IN,OUT} vs drive->mult_count == 0
check is needed also for ide_taskfile_ioctl() requests that don't have
IDE_TFLAG_FLAGGED taskfile flag set.
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_IN_DATA taskfile flag to indicate the need of reading
IDE_DATA_REG in ide_end_drive_cmd().
Set the new flag in ide_taskfile_ioctl() if ->in_flags.b.data is set.
* Add IDE_TFLAG_FLAGGED_SET_IN_FLAGS taskfile flag to indicate the
need of modifying ->in_flags in ide_taskfile_ioctl().
Set the new flag in flagged_taskfile() and move the code modifying
->tf_in_flags to ide_taskfile_ioctl().
While at it remove the bogus comment: ->tf_in_flags (except .b.data)
have no effect on selection of registers to read.
* Remove no longer needed 'tf_in_flags' field from ide_task_t.
As the result we finally have the internals of HDIO_DRIVE_TASKFILE ioctl
separated from the core IDE code.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add 'data_buf' and 'nsect' variables in ide_taskfile_ioctl()
to cache data buffer pointer and number of sectors to transfer
(this allows us to have only one ide_diag_taskfile() call).
* Add IDE_TFLAG_WRITE taskfile flag and use it to check whether
the REQ_RW request flag should be set.
* Move ->command_type handling from ide_diag_taskfile() to
ide_taskfile_ioctl() and use ->req_cmd instead of ->command_type.
* Add 'nsect' parameter to ide_raw_taskfile().
* Merge ide_diag_taskfile() into ide_raw_taskfile().
* Initialize ->data_phase explicitly in idedisk_prepare_flush(),
ide_start_power_step() and ide_disk_special().
* Remove no longer needed 'command_type' field from ide_task_t.
* Add #ifndef/#endif __KERNEL__ to <linux/hdreg.h> around no
longer used by kernel IDE_DRIVE_TASK_* and TASKFILE_* defines.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Given that:
* hpt366.c::hpt3xx_intrproc() is the only user of hwif->intrproc
* hpt366.c::hpt3xx_quirkproc() sets drive->quirk_list to 1 for quirky drives
which is a value unique to hpt366 host driver
we can remove hwif->intproc and just check for drive->quirk_list == 1
in ide_do_request().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_pktcmd_tf_load() helper and convert ATAPI device drivers to use it.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove atapi_ireason_t.
While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)
v2:
* v1 had CD and IO bits reversed in many places.
* Use CD and IO defines from <linux/hdreg.h>.
v3:
* Fix incorrect "(ireason & IO) == test_bit()". (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove ata_nsector_t, ata_data_t (unused) and atapi_bcount_t.
While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove atapi_feature_t.
While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove atapi_error_t.
While at it:
* replace 'HWIF(drive)' by 'drive->hwif'
v2:
* Add {ILI,EOM,LFS}_ERR defines to <linux/hdreg.h>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove ata_status_t (unused) and atapi_status_t.
While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
special_t is used only internally by the IDE subsystem (it isn't
related to hardware registers and isn't exported to the user-space).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_TFLAG_OUT_DEVICE taskfile flag to indicate the need of writing
the Device register and handle it in ide_tf_load().
Update ide_tf_load() and {do_rw,flagged}_taskfile() users accordingly.
* Use struct ide_taskfile and ide_tf_load() in execute_drive_cmd().
* Make the debugging code dump all taskfile registers for both
REQ_ATA_TYPE_{CMD,TASK} requests and move it to ide_tf_load()
so it also covers REQ_ATA_TYPE_TASKFILE requests.
There should be no functionality changes caused by this patch
(unless DEBUG is defined).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove stale ide.h "configuration options":
* INITIAL_MULT_COUNT - always defined to 0
* SUPPORT_SLOW_DATA_PORTS - unused
* OK_TO_RESET_CONTROLLER - always defined to 1
* DISABLE_IRQ_NOSYNC - always defined to 0
Leave SUPPORT_VLB_SYNC (defined to 0 for CRIS and FRV, otherwise to 1)
for now but disallow overriding it by <asm/ide.h>.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Based on the earlier work by Tejun Heo.
* Move setting IDE_TFLAG_LBA48 taskfile flag from do_rw_taskfile()
function to the callers.
* Add IDE_TFLAG_FLAGGED taskfile flag for flagged taskfiles coming
from ide_taskfile_ioctl(). Check it instead of ->tf_out_flags.all.
* Add IDE_TFLAG_OUT_DATA taskfile flag to indicate the need to load
IDE data register in ide_tf_load().
* Add IDE_TFLAG_OUT_* taskfile flags to indicate the need to load
particular IDE taskfile registers in ide_tf_load().
* Update do_rw_taskfile() and ide_tf_load() users to set respective
IDE_TFLAG_OUT_* taksfile flags.
* Add task_dma_ok() helper.
* Use IDE_TFLAG_FLAGGED taskfile flag to select HIHI mask in ide_tf_load().
* Use do_rw_taskfile() in flagged_taskfile().
* Remove no longer needed 'tf_out_flags' field from ide_task_t.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ide_no_data_taskfile() helper and convert ide_raw_taskfile() w/ NO DATA
protocol users to use it instead.
* Set ->data_phase explicitly in ide_no_data_taskfile()
(TASKFILE_NO_DATA is defined as 0x0000).
* Unexport task_no_data_intr().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
