| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};
See also Documentation/powerpc/dts-bindings/can/sja1000.txt.
CC: devicetree-discuss@ozlabs.org
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[PATCH net-next] bonding: allow bond in mode balance-alb to work properly in bridge -try4.3
(updated)
changes v4.2 -> v4.3
- memcpy the address always, not just in case it differs from master->dev_addr
- compare_ether_addr_64bits() is not used so there is no direct need to make new
header file (I think it would be good to have bond stuff in separate file
anyway).
changes v4.1 -> v4.2
- use skb->pkt_type == PACKET_HOST compare rather then comparing skb dest addr
against skb->dev->dev_addr
The problem is described in following bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=487763
Basically here's what's going on. In every mode, bonding interface uses the same
mac address for all enslaved devices (except fail_over_mac). Only balance-alb
will simultaneously use multiple MAC addresses across different slaves. When you
put this kind of bond device into a bridge it will only add one of mac adresses
into a hash list of mac addresses, say X. This mac address is marked as local.
But this bonding interface also has mac address Y. Now then packet arrives with
destination address Y, this address is not marked as local and the packed looks
like it needs to be forwarded. This packet is then lost which is wrong.
Notice that interfaces can be added and removed from bond while it is in bridge.
***
When the multiple addresses for bridge port approach failed to solve this issue
due to STP I started to think other way to solve this. I returned to previous
solution but tweaked one.
This patch solves the situation in the bonding without touching bridge code.
For every incoming frame to bonding the destination address is compared to
current address of the slave device from which tha packet came. If these two
match destination address is replaced by mac address of the master. This address
is known by bridge so it is delivered properly. Note that the comparsion is not
made directly, it's used skb->pkt_type == PACKET_HOST instead. This is "set"
previously in eth_type_trans().
I experimentally tried that this works as good as searching through the slave
list (v4 of this patch).
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax
|
|
As the 'state_get' API call was added, we need to increase the minor
protocol version number so applications that depend on the can check
it's presence.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
|
wimax connection manager / daemon has to know what is current
state of the device. Previously it was only possible to get
notification whet state has changed.
Note:
By mistake, the new generic netlink's number for
WIMAX_GNL_OP_STATE_GET was declared inserting into the existing list
of API calls, not appending; thus, it'd break existing API.
Fixed by Inaky Perez-Gonzalez <inaky@linux.intel.com> by moving to
the tail, where we add to the interface, not modify the interface.
Thanks to Stephen Hemminger <shemminger@vyatta.com> for catching this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ALIGN() and PTR_ALIGN() macros instead of handcoding them.
Get rid of NETDEV_ALIGN_CONST ugly define
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the overwhelming majority of cases, skb_gro_header's return
value cannot be NULL. Yet we must check it because of its current
form. This patch splits it up into multiple functions in order
to avoid this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By caching frag0_len, we can avoid checking both frag0 and the
length separately in skb_gro_header. This helps as skb_gro_header
is called four times per packet which amounts to a few million
times at 10Gb/s.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently skb_gro_header is used for packets which put the hardware
header in skb->data with the rest in frags. Since the drivers that
need this optimisation all provide completely non-linear packets,
we can gain extra optimisations by only performing the frag0
optimisation for completely non-linear packets.
In particular, we can simply test frag0 (instead of skb_headlen)
to see whether the optimisation is in force.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function skb_gro_header is called four times per packet which
quickly adds up at 10Gb/s. This patch inlines it to allow better
optimisations.
Some architectures perform multiplication for page_address, which
is done by each skb_gro_header invocation. This patch caches that
value in skb->cb to avoid the unnecessary multiplications.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just use the constant 20 to keep things working.
If someone is so motivated, this can be converted over to
dynamic strings. I tried and it's a lot of work.
But for now this is good enough.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We would like to get rid of netdev->trans_start = jiffies; that about all net
drivers have to use in their start_xmit() function, and use txq->trans_start
instead.
This can be done generically in core network, as suggested by David.
Some devices, (particularly loopback) dont need trans_start update, because
they dont have transmit watchdog. We could add a new device flag, or rely
on fact that txq->tran_start can be updated is txq->xmit_lock_owner is
different than -1. Use a helper function to hide our choice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new ID is validated by Cologne Chip.
LEDs control is also supported.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch make debug printk's KERN_DEBUG and also fix some
codestyle issues.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
new id for HFC-8S
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New version without emulating arch specific stuff for the other
architectures, the special IO and init functions for the 8xx
microcontroller are in a separate include file.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IMHOLD_L1 ioctl.
The feature will be disabled on closing.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added tx-fifo information for calculation of current delay to sync tx and rx
streams for echo canceler.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch was made by Titus Moldovan and provides IOCTL functions for enabling
and disabling the controller's built in watchdog. The use is optional.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This introduces genl_register_family_with_ops() that registers a genetlink
family along with operations from a table. This is used to kill copy'n'paste
occurrences in following patches.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch to add the ability to detect drops in hardware interfaces via dropwatch.
Adds a tracepoint to net_rx_action to signal everytime a napi instance is
polled. The dropmon code then periodically checks to see if the rx_frames
counter has changed, and if so, adds a drop notification to the netlink
protocol, using the reserved all-0's vector to indicate the drop location was in
hardware, rather than somewhere in the code.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/linux/net_dropmon.h | 8 ++
include/trace/napi.h | 11 +++
net/core/dev.c | 5 +
net/core/drop_monitor.c | 124 ++++++++++++++++++++++++++++++++++++++++++--
net/core/net-traces.c | 4 +
net/core/netpoll.c | 2
6 files changed, 149 insertions(+), 5 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The the PACKET_ADD_MEMBERSHIP and the PACKET_DROP_MEMBERSHIP setsockopt
calls for af_packet already has all of the infrastructure needed to subscribe
to multiple mac addresses. All that is missing is a flag to say that
the address we want to listen on is a unicast address.
So introduce PACKET_MR_UNICAST and wire it up to dev_unicast_add and
dev_unicast_delete.
Additionally I noticed that errors from dev_mc_add were not propagated
from packet_dev_mc so fix that.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netlink message header (struct nlmsghdr) is an unused parameter in
fill method of fib_rules_ops struct. This patch removes this
parameter from this method and fixes the places where this method is
called.
(include/net/fib_rules.h)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moving information from config_interface to bss_info_changed
removed struct ieee80211_if_conf which the documentation still
refers to, additionally there's one kernel-doc description too
much and one other missing, fix all this.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some applications using wireless extensions expect to be able to
remove a key that doesn't exist. One example is wpa_supplicant
which doesn't actually change behaviour when running into an
error while trying to do that, but it prints an error message
which users interpret as wpa_supplicant having problems.
The safe thing to do is not change the behaviour of wireless
extensions any more, so when the driver reports -ENOENT let
the wext bridge code return success to userspace. To guarantee
this, also document that drivers should return -ENOENT when the
key doesn't exist.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows drivers to use a const pointer as the privid without a cast.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows drivers to mark their cfg80211_ops tables const.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.
We end up dealing with HT40 by having two passes for each channel.
The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.
The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:
o exist
o are enabled
o regulatory allows 40 MHz bandwidth on its frequency range
This work allows allows us to idependently check for HT40- and
HT40+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
be sent periodically. The rs_delay can be speficied when adding the
PRL entry and defaults to 15 minutes.
The RS is sent from every link local adress that's assigned to the
tunnel interface. It's directed to the (guessed) linklocal address
of the router and is sent through the tunnel.
Better: send to ff02::2 encapsuled in unicast directed to router-v4.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).
CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.
It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.
David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().
List of devices that must clear this flag is :
- loopback device, because it calls netif_rx() and quoting Patrick :
"ip_route_input() doesn't accept loopback addresses, so loopback packets
already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function
- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when we have a signal pending we have the functionality
to restart that the current system call. There are other cases
such as nasty lock ordering issues where it makes sense to have
a simple fix that uses try lock and restarts the system call.
Buying time to figure out how to rework the locking strategy.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New packet socket feature that makes packet socket more efficient for
transmission.
- It reduces number of system call through a PACKET_TX_RING mechanism,
based on PACKET_RX_RING (Circular buffer allocated in kernel space
which is mmapped from user space).
- It minimizes CPU copy using fragmented SKB (almost zero copy).
Signed-off-by: Johann Baudy <johann.baudy@gnu-log.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/scsi/fcoe/fcoe.c
|
|
This driver adds support for the SJA1000 chips connected to the
"platform bus", which can be found on various embedded systems.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.
Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.
For further information please check "Documentation/networking/can.txt"
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
offsetof(struct net_device, features)=0x44
offsetof(struct net_device, stats.tx_packets)=0x54
offsetof(struct net_device, stats.tx_bytes)=0x5c
offsetof(struct net_device, stats.tx_dropped)=0x6c
Network drivers that touch dev->stats.tx_packets/stats.tx_bytes in their
tx path can slow down SMP operations, since they dirty a cache line
that should stay shared (dev->features is needed in rx and tx paths)
We could move away stats field in net_device but it wont help that much.
(Two cache lines dirtied in tx path, we can do one only)
Better solution is to add tx_packets/tx_bytes/tx_dropped in struct
netdev_queue because this structure is already touched in tx path and
counters updates will then be free (no increase in size)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
If we can find a type NETDEV_HW_ADDR_T_SAN mac address from the
corresponding netdev for a fcoe interface then sets up added the
fc->ctlr.spma flag and stores spma mode address in ctl_src_addr.
In case the spma flag is set then:-
1. Adds spma mode MAC address in ctl_src_addr as secondary
MAC address, the FLOGI for FIP and pre-FIP will go out
using this address.
2. Cleans up stored spma MAC address in ctl_src_addr in
fcoe_netdev_cleanup.
3. Sets up spma bit in fip_flags for FIP solicitations along
with exiting FPMA bit setting.
4. Initialize the FLOGI FIP MAC descriptor to stored spma
MAC address in ctl_src_addr. This is used as proposed
FCoE MAC address from initiator along with both SPMA
and FPMA bit set in FIP solicitation, in response the
switch may grant any FPMA or SPMA mode MAC address to
initiator.
Removes FIP descriptor type checking against ELS type
ELS_FLOGI in fcoe_ctlr_encaps to update a FIP MAC descriptor,
instead now checks against FIP_DT_FLOGI.
I've tested this with available FPMA-only FCoE switch but
since data_src_addr is updated using same old code for
both FPMA and SPMA modes with FIP or pre-FIP links, so added
SPMA mode will work with SPMA-only switch also provided that
switch grants a valid MAC address.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These registers were originally defined for XENPAK modules, but are
also implemented by many other 10G PHYs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These do not have an in-kernel user but may be useful to user-space.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct net_device trans_start field is a hot spot on SMP and high performance
devices, particularly multi queues ones, because every transmitter dirties
it. Is main use is tx watchdog and bonding alive checks.
But as most devices dont use NETIF_F_LLTX, we have to lock
a netdev_queue before calling their ndo_start_xmit(). So it makes
sense to move trans_start from net_device to netdev_queue. Its update
will occur on a already present (and in exclusive state) cache line, for
free.
We can do this transition smoothly. An old driver continue to
update dev->trans_start, while an updated one updates txq->trans_start.
Further patches could also put tx_bytes/tx_packets counters in
netdev_queue to avoid dirtying dev->stats (vlan device comes to mind)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add new GET_PIPE_FROM_CRTC_ID ioctl.
drm/i915: Set HDMI hot plug interrupt enable for only the output in question.
drm/i915: Include 965GME pci ID in IS_I965GM(dev) to match UMS.
drm/i915: Use the GM45 VGA hotplug workaround on G45 as well.
drm/i915: ignore LVDS on intel graphics systems that lie about having it
drm/i915: sanity check IER at wait_request time
drm/i915: workaround IGD i2c bus issue in kernel side (v2)
drm/i915: Don't allow binding objects into the last page of the aperture.
drm/i915: save/restore fence registers across suspend/resume
drm/i915: x86 always has writeq. Add I915_READ64 for symmetry.
|
|
This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.
The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard. Only then are the
characteristics reported to SCSI via the VPD B1 page.
This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever. With no complaints so far.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
