Age | Commit message (Collapse) | Author |
|
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds fields to ieee80211_tx_status in order to allow block ack
information exchange between low-level driver,mac80211 and rate scaling
module.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch allows qdisc support in A-MPDU Tx. a method to
handle QoS <-> TID switches is present in this patch.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds the API for 3 stages in A-MPDU Tx session flow:
- request mac80211 to start/stop A-MPDU Tx session for specific TID. such a
request should be issued by a load aware element, either mac80211 itself
or external element.
- requests by mac80211 to low-level driver to start/stop Tx aggregation.
notice that low level driver responds now with Starting Sequence Number.
- async feedback by low-level to mac80211 to inform that HW is ready for
next A-MPDU Tx state.
Changes in API to Rx A-MPDU were also made, reflected in iwlwifi changes as
well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Skip the prefix length matching in source address selection for
orchid -> non-orchid addresses.
Overlay Routable Cryptographic Hash IDentifiers (RFC 4843,
2001:10::/28) are currenty not globally reachable. Without this
check a host with an ORCHID address can end up preferring those over
regular addresses when talking to other regular hosts in the 2001::/16
range thus breaking non-orchid connections.
Signed-off-by: Juha-Matti Tapio <jmtapio@verkkotelakka.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add namespace parameter to devinet_ioctl and locate device inside it for
state changes.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/vxy/lksctp-dev
|
|
The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
Properly add parens around the macro argument. This is not needed by
the kernel but the macro is exported to userspace, so it shouldn't
make any assumptions.
Also use NF_VERDICT_BITS instead of NF_VERDICT_QBTIS for the left-shift
since thats whats logically correct.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is used in connector.c only, so make it static.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't require platform code to be #ifdeffed according to whether
I2C is enabled or not ... if it's not enabled, let GCC compile out
all I2C device declarations. (Issue noted on an NSLU2 build that
didn't configure I2C.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Commit 8b798c4d16b762d15f4055597ff8d87f73b35552 broke
alchemy build, fix it. Pointed out by Adrian Bunk.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-core: fix kernel-doc warning
sata_fsl: fix build with ATA_VERBOSE_DEBUG
[libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
libata-pmp: clear hob for pmp register accesses
libata: automatically use DMADIR if drive/bridge requires it
power_state: get rid of write-only variable in SATA
pata_atiixp: Use 255 sector limit
|
|
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.
That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).
So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.
This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.
Original patch is from Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
[NETFILTER]: fix ebtable targets return
[IP_TUNNEL]: Don't limit the number of tunnels with generic name explicitly.
[NET]: Restore sanity wrt. print_mac().
[NEIGH]: Fix race between neighbor lookup and table's hash_rnd update.
[RTNL]: Validate hardware and broadcast address attribute for RTM_NEWLINK
tg3: ethtool phys_id default
[BNX2]: Update version to 1.7.4.
[BNX2]: Disable parallel detect on an HP blade.
[BNX2]: More 5706S link down workaround.
ssb: Fix support for PCI devices behind a SSB->PCI bridge
zd1211rw: fix sparse warnings
rtl818x: fix sparse warnings
ssb: Fix pcicore cardbus mode
ssb: Make the GPIO API reentrancy safe
ssb: Fix the GPIO API
ssb: Fix watchdog access for devices without a chipcommon
ssb: Fix serial console on new bcm47xx devices
ath5k: Fix build warnings on some 64-bit platforms.
WDEV, ath5k, don't return int from bool function
WDEV: ath5k, fix lock imbalance
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: make IOMMU code respect the segment boundary limits
[SPARC64]: Fix cpu trampoline et al. mismatch warnings.
[SPARC64]: More sparse warning fixes in process.c
[SPARC64]: Fix sparse warning wrt. fault_in_user_windows.
[SPARC64]: Kill show_regs32().
[SPARC64]: Fix sparse warnings wrt. __show_regs().
[SPARC64]: Kill show_stackframe{,32}().
[SPARC64]: Fix sparse warnings wrt. machine_alt_power_off().
|
|
Use the added dev_alloc_name() call to create tunnel device name,
rather than iterate in a hand-made loop with an artificial limit.
Thanks Patrick for noticing this.
[ The way this works is, when the device is actually registered,
the generic code noticed the '%' in the name and invokes
dev_alloc_name() to fully resolve the name. -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAC_FMT had only one user and we tried to get rid of
that, but this created more problems than it solved.
As a result, this reverts three commits:
235365f3aaaa10b7056293877c0ead50425f25c7 ("net/8021q/vlan_dev.c: Use
print_mac."), fea5fa875eb235dc186b1f5184eb36abc63e26cc ("[NET]: Remove
MAC_FMT"), and 8f789c48448aed74fe1c07af76de8f04adacec7d ("[NET]:
Elminate spurious print_mac() calls.")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- replace old name 'cont' with 'cgrp' (Paul Menage did this cleanup for
cgroup.c in commit bd89aabc6761de1c35b154fe6f914a445d301510)
- remove a duplicate declaration of cgroup_path()
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fix:
- comments about need_forkexit_callback
- comments about release agent
- typo and comment style, etc.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- add missing file and declare.
- remove unused file and macros.
- some cleanup.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
get_user const *ptr access fix.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Not all architectures implement futex_atomic_cmpxchg_inatomic(). The default
implementation returns -ENOSYS, which is currently not handled inside of the
futex guts.
Futex PI calls and robust list exits with a held futex result in an endless
loop in the futex code on architectures which have no support.
Fixing up every place where futex_atomic_cmpxchg_inatomic() is called would
add a fair amount of extra if/else constructs to the already complex code. It
is also not possible to disable the robust feature before user space tries to
register robust lists.
Compile time disabling is not a good idea either, as there are already
architectures with runtime detection of futex_atomic_cmpxchg_inatomic support.
Detect the functionality at runtime instead by calling
cmpxchg_futex_value_locked() with a NULL pointer from the futex initialization
code. This is guaranteed to fail, but the call of
futex_atomic_cmpxchg_inatomic() happens with pagefaults disabled.
On architectures, which use the asm-generic implementation or have a runtime
CPU feature detection, a -ENOSYS return value disables the PI/robust features.
On architectures with a working implementation the call returns -EFAULT and
the PI/robust features are enabled.
The relevant syscalls return -ENOSYS and the robust list exit code is blocked,
when the detection fails.
Fixes http://lkml.org/lkml/2008/2/11/149
Originally reported by: Lennart Buytenhek
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Riku Voipio <riku.voipio@movial.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge include/linux/efs_fs{_i,_dir}.h into fs/efs/efs.h. efs_vh.h remains
there because this is the IRIX volume header and shouldn't really be
handled by efs but by the partitioning code. efs_sb.h remains there for
now because it's exported to userspace. Of course this wrong and aboot
should have a copy of it's own, but I'll leave that to a separate patch to
avoid any contention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface. As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin. (This probably means all
transfers are one bit out of sequence.)
This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity. The fix
assures that the clock mode is properly set before asserting chip select.
This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make is_vmalloc_addr() contingent on CONFIG_MMU=y, as it won't compile
in !MMU mode.
[ Bug introduced in commit 9e2779fa281cfda13ac060753d674bbcaa23367e:
"is_vmalloc_addr(): Check if an address is within the vmalloc
boundaries" ].
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix build failure on sparc:
In file included from include/linux/mm.h:39,
from include/linux/memcontrol.h:24,
from include/linux/swap.h:8,
from include/linux/suspend.h:7,
from init/do_mounts.c:6:
include/asm/pgtable.h:344: warning: parameter names (without
types) in function declaration
include/asm/pgtable.h:345: warning: parameter names (without
types) in function declaration
include/asm/pgtable.h:346: error: expected '=', ',', ';', 'asm' or
'__attribute__' before '___f___swp_entry'
viro sayeth:
I've run allmodconfig builds on a bunch of target, FWIW (essentially the
same patch). Note that these includes are recent addition caused by added
inline function that had since then become a define. So while I agree with
your comments in general, in _this_ case it's pretty safe.
The commit that had done it is 3062fc67dad01b1d2a15d58c709eff946389eca4
("memcontrol: move mm_cgroup to header file") and the switch to #define
is in commit 60c12b1202a60eabb1c61317e5d2678fcea9893f ("memcontrol: add
vm_match_cgroup()") (BTW, that probably warranted mentioning in the
changelog of the latter).
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Robert Reif <reif@earthlink.net>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Define SO_MARK for MN10300.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Define HZ as a config option.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
2.6.25-rc1 percpu changes broke CONFIG_DEBUG_PREEMPT's per_cpu checking
on several architectures. On s390, sparc64 and x86 it's been weakened to
not checking at all; whereas on powerpc64 it's become too strict, issuing
warnings from __raw_get_cpu_var in io_schedule and init_timer for example.
Fix this by weakening powerpc's __my_cpu_offset to use the non-checking
local_paca instead of get_paca (which itself contains such a check);
and strengthening the generic my_cpu_offset to go the old slow way via
smp_processor_id when CONFIG_DEBUG_PREEMPT (debug_smp_processor_id is
where all the knowledge of what's correct when lives).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Reviewed-by: Mike Travis <travis@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add proper ifdef's to the patch loading code moved from the old instr
layer so that opl3 driver can be compiled without the sequencer support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix macro argument substitution in PageHead() and PageTail() - 'page' should
have brackets surrounding it (commit 6d7779538f765963ced45a3fa4bed7ba8d2c277d).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (26 commits)
PM: Make suspend_device() static
PCI ACPI: Fix comment describing acpi_pci_choose_state
Hibernation: Handle DEBUG_PAGEALLOC on x86
ACPI: fix build warning
ACPI: TSC breaks atkbd suspend
ACPI: remove is_processor_present prototype
acer-wmi: Add DMI match for mail LED on Acer TravelMate 4200 series
ACPI: sparse fix, replace macro with static function
ACPI: thinkpad-acpi: add tablet-mode reporting
ACPI: thinkpad-acpi: minor hotkey_radio_sw fixes
ACPI: thinkpad-acpi: improve thinkpad-acpi input device documentation
ACPI: thinkpad-acpi: issue input events for tablet swivel events
ACPI: thinkpad-acpi: make the video output feature optional
ACPI: thinkpad-acpi: synchronize input device switches
ACPI: thinkpad-acpi: always track input device open/close
ACPI: thinkpad-acpi: trivial fix to documentation
ACPI: thinkpad-acpi: trivial fix to module_desc typo
intel_menlo: extract return values using PTR_ERR
ACPI video: check for error from thermal_cooling_device_register
ACPI thermal: extract return values using PTR_ERR
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix wrong reference counter check for proc_dir_entry
PCI: fix up setup-bus.c #ifdef
PCI: don't load acpi_php when acpi is disabled
PCI: quirks: set 'En' bit of MSI Mapping for devices onHT-based nvidia platform
PCI: kernel-doc: fix pci-acpi warning
PCI: irq: patch for Intel ICH10 DeviceID's
PCI: pci_ids: patch for Intel ICH10 DeviceID's
PCI: AMD SATA IDE mode quirk
PCI: drivers/pcmcia/i82092.c: fix up after pci_bus_region changes
PCI: hotplug: acpiphp_ibm: Remove get device information
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4835/1: Fix stale comment in struct machine_desc description
[ARM] 4829/1: add .get method to pxa-cpufreq to silence a warning
[ARM] 4828/1: fix 3 warnings in drivers/video/pxafb.c
[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c
[ARM] 4826/1: Orion: Register the RTC interrupt on the TS-209
[ARM] pxa: fix clock lookup to find specific device clocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] pasemi: Remove warning in mpic_pasemi_msi.c
[POWERPC] pasemi: Register i2c devices at boot
[POWERPC] cell: fix spurious false return from spu_trap_data_{map,seg}
[POWERPC] Fix warning in pseries/power.c
[POWERPC] Fix bootwrapper builds with older gcc versions
[POWERPC] Fix dt_mem_next_cell() to read the full address
[POWERPC] Kill sparse warnings in kprobes
[POWERPC] spufs: fix scheduler starvation by idle contexts
[POWERPC] 44x: Add multiplatform defconfig
[POWERPC] 44x: Fix Kconfig formatting
[POWERPC] 4xx: Update defconfigs for 2.6.25
[POWERPC] 4xx: Remove "i2c" and "xxmii-interface" device_types from dts
[POWERPC] PPC440EP Interrupt Triggering and Level Settings
[POWERPC] net: NEWEMAC: Remove "rgmii-interface" from rgmii matching table
|
|
This patch adds the Intel ICH10 LPC and SMBus Controller DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch updates stale comment that pointed to nonexistent file.
Signed-off-by: Leonid Evdokimov <leon@darkk.net.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Make hibernation work with CONFIG_DEBUG_PAGEALLOC set on x86, by
checking if the pages to be copied are marked as present in the
kernel mapping and temporarily marking them as present if that's not
the case. No functional modifications are introduced if
CONFIG_DEBUG_PAGEALLOC is unset.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Change the FRV timerfd syscalls to be the same as i386 timerfd syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: fix kernel-doc parameter warning
sata_mv: remove iounmap in mv_platform_remove and use devm_iomap
ata: fix sparse warning in libata.h
libata: implement libata.force module parameter
sata_mv: use hpriv->base instead of the host->iomap
sata_mv: Define module alias for platform device
ata: fix sparse warnings in pata_legacy.c
|
|
Noted by various people (Sam, Jeff, Roland..)
Commit 58b7983d15a422d9616bdc4e245d5c31dfaefbe2 intended to remove the
xfs "Makefile-linux-2.6" file, but it was mistakenly still left in the
tree as a empty file, and would cause git to correctly complain about a
tracked file being removed after a "make distclean" (which removes empty
files as garbage).
And the asm-x86/desc_64.h file was supposed to be removed by commit
c81c6ca45a69478c7877b729af1942d2b80ef582, but instead stayed around
containing just a single newline.
Get rid of them both properly.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes the pcicore driver to not die a horrible
crash death when inserting a cardbus card.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes the GPIO API to be reentrancy safe.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes the GPIO API to be usable.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes the SSB watchdog access for devices without a chipcommon.
These devices have the watchdog on the extif.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes the baud settings for new devices
like the Linksys WRT350n.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Avoids lots of these, also is more readable.
include/linux/libata.h:1210:13: warning: potentially expensive pointer subtraction
Change the subtraction to addition on the other side of the comparison.
Thanks to Christer Weinigel for the suggestion.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|