| Age | Commit message (Collapse) | Author |
|---|
|
http://bugme.osdl.org/show_bug.cgi?id=4016
Written-by: David Shaohua Li <shaohua.li@intel.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ACPI 3.0 added a Correctable Platform Error Interrupt (CPEI)
Processor Overide flag to MADT.Platform_Interrupt_Source.
Record the processor that was provided as hint from ACPI.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Implement the framework for binding physical devices
with ACPI devices. A physical bus like PCI bus
should create a 'acpi_bus_type', with:
.find_device:
For device which has parent such as normal PCI devices.
.find_bridge:
It's for special devices, such as PCI root bridge
or IDE controller. Such devices generally haven't a
parent or ->bus. We use the special method
to get an ACPI handle.
Uses new field in struct device: firmware_data
http://bugzilla.kernel.org/show_bug.cgi?id=4277
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
See Documentation/acpi-hotkey.txt
Use cmdline "acpi_specific_hotkey" to enable
legacy platform specific drivers.
http://bugzilla.kernel.org/show_bug.cgi?id=3887
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Register an "acpi" system device to be notified of shutdown preparation.
This depends on CONFIG_PM
http://bugzilla.kernel.org/show_bug.cgi?id=4041
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Patch from Catalin Marinas
The initial IB2 addresses did not depend on the IB2 base. This
patch defines them as (VERSATILE_IB2_BASE + offset).
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Catalin Marinas
The GPIO base for Integrator/CP is different from the
Integrator/AP. This patch sets the correct value for
INTEGRATOR_GPIO_BASE.
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch alows you to change the source address of icmp error
messages. It applies cleanly to 2.6.11.11 and retains the default
behaviour.
In the old (default) behaviour icmp error messages are sent with the ip
of the exiting interface.
The new behaviour (when the sysctl variable is toggled on), it will send
the message with the ip of the interface that received the packet that
caused the icmp error. This is the behaviour network administrators will
expect from a router. It makes debugging complicated network layouts
much easier. Also, all 'vendor routers' I know of have the later
behaviour.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<linux/if_tr.h> uses __be16, but does not directly include
<asm/byteorder.h>. Add this in, so that dhcp/net-tools token ring code
can compile again.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now m68k no longer sets HAVE_ARCH_GET_SIGNAL_TO_DELIVER, can it be removed
completely? Or may ARM26 still need it? Note that its usage was removed from
kernel/signal.c about 2 months ago.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
This patch fixes some bugs in the ppc64 PER_LINUX32 implementation,
noted by Juergen Kreileder:
* uname(2) doesn't respect PER_LINUX32, it returns 'ppc64' instead of 'ppc'
* Child processes of a PER_LINUX32 process don't inherit PER_LINUX32
Along the way I took the opportunity to move things around so that
sys_ppc32.c only has 32-bit syscall emulation functions and to remove
the obsolete "fakeppc" command line option.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
There've been reports of problems with CONFIG_PREEMPT=y and the high
floating point partition. This is caused by the possibility of preemption
and rescheduling on a different processor while saving or restioirng the
high partition.
The only places where the FPU state is touched are in ptrace, in
switch_to(), and where handling a floating-point exception. In switch_to()
preemption is off. So it's only in trap.c and ptrace.c that we need to
prevent preemption.
Here is a patch that adds commentary to make the conditions clear, and adds
appropriate preempt_{en,dis}able() calls to make it so. In trap.c I use
preempt_enable_no_resched(), as we're about to return to user space where
the preemption flag will be checked anyway.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The fact that access_ok() doesn't use some of its arguments trips some
unused variable warnings. This patch silences them permanently.
Signed-off-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Adds meta collectors for all socket attributes that make sense
to be filtered upon. Some of them are only useful for debugging
but having them doesn't hurt.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 5700/5701 DMA write corruption on Apple G4 by detecting the Apple
UniNorth PCI 1.5 chipset and adjusting the DMA write boundary to 16. DMA
test fails to detect the problem with this chipset.
Thanks to Manuel Perez Ayala for reporting the problem and helping to
debug it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PXA27x
Patch from Giorgio Padrin
The patch completes I2S GPIO alternate functions for PXA27x, adding I2S_SYSCLK.
File: pxa-regs.h .
Signed-off-by: Giorgio Padrin
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This fixes an oops reported by Jason Baron.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
|
|
In file included from arch/i386/kernel/smp.c:235:
include/asm-i386/mach-numaq/mach_ipi.h:4: warning: `send_IPI_mask_sequence'
declared inline after its definition
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When Linux is running on the Xen virtual machine monitor, physical
addresses are virtualised and cannot be directly referenced by the AGP
GART. This patch fixes the GART driver for Xen by adding a layer of
abstraction between physical addresses and 'GART addresses'.
Architecture-specific functions are also defined for allocating and freeing
the GATT. Xen requires this to ensure that table really is contiguous from
the point of view of the GART.
These extra interface functions are defined as 'no-ops' for all existing
architectures that use the GART driver.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Attached is a small patch for i945G support against 2.6.11.11.
From: Alan Hourihane <alanh@fairlite.demon.co.uk>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
I'm not sure why this issue is suddenly showing, but without this
patchlet, the zx1 config won't compile anymore (e.g., to see the
compilation-error, look for "***" in [1]).
[1] http://www.gelato.unsw.edu.au/kerncomp/results//2005-06-06-17-00/zx1_defconfig-log.html
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
On ppc32, <asm/sigcontext.h> uses __user, but doesn't directly include
<linux/compiler.h>. This adds that in. Without this, glibc will not
compile.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
h8300 was missing a few definitions.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
To make UML build and run on s390, I needed to do these two little
changes:
1) UML includes some of the subarch's (s390) headers. I had to
change one of them with the following one-liner, to make this
compile. AFAICS, this change doesn't break compilation of s390
itself.
2) UML needs to intercept syscalls via ptrace to invalidate the syscall,
read syscall's parameters and write the result with the result of
UML's syscall processing. Also, UML needs to make sure, that the host
does no syscall restart processing. On i386 for example, this can be
done by writing -1 to orig_eax on the 2nd syscall interception
(orig_eax is the syscall number, which after the interception is used
as a "interrupt was a syscall" flag only.
Unfortunately, s390 holds syscall number and syscall result in gpr2 and
its "interrupt was a syscall" flag (trap) is unreachable via ptrace.
So I changed the host to set trap to -1, if the syscall number is changed
to an invalid value on the first syscall interception.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Patch from Mike Frysinger
the ELF_DATA define in both arm asm subdirs of linux/include/ contain a
semicolon at the end. this of course will cause any code that tries to use
ELF_DATA in assignment or comparison to fail. no other arch has a semicolon
in their ELF_DATA defines.
Signed-off-by: Mike Frysinger
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Deepak Saxena
This patch fixes the following warnings:
include/asm/arch/io.h: In function `insw':
include/asm/arch/io.h:78: warning: comparison of distinct pointer types
lacks acast
include/asm/arch/io.h:79: warning: comparison of distinct pointer types
lacks acast
include/asm/arch/io.h: In function `outsw':
include/asm/arch/io.h:103: warning: comparison of distinct pointer types
lacks a cast
include/asm/arch/io.h:104: warning: comparison of distinct pointer types
lacks a cast
include/asm/arch/io.h: In function `inw':
include/asm/arch/io.h:127: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
On Wed, May 04, 2005 at 01:37:30PM -0700, David Brownell wrote:
> On Wednesday 04 May 2005 12:19 pm, Roman Kagan wrote:
> > struct urb {
> > /* private, usb core and host controller only fields in the urb */
> > ...
> > struct list_head urb_list; /* list pointer to all active urbs */
> > ...
> > };
> >
> > Is it safe to use it for driver's purposes when the driver owns the urb,
> > that is, starting from the completion routine until the urb is submitted
> > with usb_submit_urb()?
>
> Right now, it should be.
Great! FWIW I've briefly tested a modified version of usbatm using
the list head in struct urb instead of creating a wrapper struct, and I
haven't seen any failures yet. So I tend to believe that your "should
be" actually means "is" :)
> > If it is, can it be guaranteed in future, e.g.
> > by moving the list head into the public section of struct urb?
>
> In fact I'm not sure why it ever got called "private" to usbcore/hcds.
> I thought the idea was that it should be like urb->status, reserved for
> whoever controls the URB.
OK then how about the following (essentially documentation) patch?
Signed-off-by: Roman Kagan <rkagan@mail.ru>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
|
|
When the hardware header size is a multiple of HH_DATA_MOD, HH_DATA_OFF()
incorrectly returns HH_DATA_MOD (instead of 0). This affects ieee80211 layer
as 802.11 header is 32 bytes long.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o use a semaphore instead of an opencoded and racy lock
o move locking out of shaper_kick and into the callers - most just
released the lock before calling shaper_kick
o remove in_interrupt() tests. from ->close we can always block, from
->hard_start_xmit and timer context never
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
|
|
|
|
|
|
The iseries has a bar graph on the front panel that shows how busy it is.
The operating system sets and clears a bit in the CTRL register to control
it.
Instead of going to the complexity of using a thread info bit, just set and
clear it in the idle loop.
Also create two helper functions, ppc64_runlatch_on and ppc64_runlatch_off.
Finally don't use the short form of the SPR defines.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There are a bunch of irrelevant SPR definitions in asm/processer.h. Cut
them down a bit, also add a DABR_TRANSLATION define which will be used
shortly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6
|
|
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6
|
|
This cleans up the /proc/device-tree representation of the Open Firmware
device-tree on ppc and ppc64. It does the following things:
- Workaround an issue in some Apple device-trees where a property may
exist with the same name as a child node of the parent. We now
simply "drop" the property instead of creating duplicate entries in
/proc with random result...
- Do not try to chop off the "@0" at the end of a node name whose unit
address is 0. This is not useful, inconsistent, and the code was
buggy and didn't always work anyway.
- Do not create symlinks for the short name and unit address parts of a
node. These were never really used, bloated the memory footprint of
the device-tree with useless struct proc_dir_entry and their matching
dentry and inode cache bloat.
This results in smaller code, smaller memory footprint, and a more
accurate view of the tree presented to userland.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix up comment in cpufreq.h stating transition latency should be passed
in microseconds -- it was decided long ago to switch to nanoseconds.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Some cpufreq drivers (at that time, only powernow-k7) need to recalibrate the
cpu_khz at runtime.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Firstly, if the direction is TODEVICE, then dirty data in the
streaming cache is impossible so we can elide the flush-flag
synchronization in that case.
Next, the context allocator is broken. It is highly likely
that contexts get used multiple times for different dma
mappings, which confuses the strbuf flushing code and makes
it run inefficiently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here's the 2.6 amd74xx patch for NVIDIA MCP51.
Signed-off-by: Andy Currid <acurrid@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
|
|
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
