aboutsummaryrefslogtreecommitdiff
path: root/net/bluetooth/af_bluetooth.c
AgeCommit message (Collapse)Author
2008-10-16net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)Johannes Berg
Some code here depends on CONFIG_KMOD to not try to load protocol modules or similar, replace by CONFIG_MODULES where more than just request_module depends on CONFIG_KMOD and and also use try_then_request_module in ebtables. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-09[Bluetooth] Reject L2CAP connections on an insecure ACL linkMarcel Holtmann
The Security Mode 4 of the Bluetooth 2.1 specification has strict authentication and encryption requirements. It is the initiators job to create a secure ACL link. However in case of malicious devices, the acceptor has to make sure that the ACL is encrypted before allowing any kind of L2CAP connection. The only exception here is the PSM 1 for the service discovery protocol, because that is allowed to run on an insecure ACL link. Previously it was enough to reject a L2CAP connection during the connection setup phase, but with Bluetooth 2.1 it is forbidden to do any L2CAP protocol exchange on an insecure link (except SDP). The new hci_conn_check_link_mode() function can be used to check the integrity of an ACL link. This functions also takes care of the cases where Security Mode 4 is disabled or one of the devices is based on an older specification. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-18[Bluetooth] Consolidate maintainers informationMarcel Holtmann
The Bluetooth entries for the MAINTAINERS file are a little bit too much. Consolidate them into two entries. One for Bluetooth drivers and another one for the Bluetooth subsystem. Also the MODULE_AUTHOR should indicate the current maintainer of the module and actually not the original author. Fix all Bluetooth modules to provide current maintainer information. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Update Bluetooth core version numberMarcel Holtmann
With all the Bluetooth 2.1 changes and the support for Simple Pairing, it is important to update the Bluetooth core version number. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Add support for TIOCOUTQ and TIOCINQ ioctlsMarcel Holtmann
Almost every protocol family supports the TIOCOUTQ and TIOCINQ ioctls and even Bluetooth could make use of them. When implementing audio streaming and integration with GStreamer or PulseAudio they will allow a better timing and synchronization. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Add timestamp support to L2CAP, RFCOMM and SCOMarcel Holtmann
Enable the common timestamp functionality that the network subsystem provides for L2CAP, RFCOMM and SCO sockets. It is possible to either use SO_TIMESTAMP or the IOCTLs to retrieve the timestamp of the current packet. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-04-01bluetooth : use lockdep sub-classes for diffrent bluetooth protocolDave Young
'rfcomm connect' will trigger lockdep warnings which is caused by locking diffrent kinds of bluetooth sockets at the same time. So using sub-classes per AF_BLUETOOTH sub-type for lockdep. Thanks for the hints from dave jones. --- > From: Dave Jones <davej@codemonkey.org.uk> > Date: Thu, 27 Mar 2008 12:21:56 -0400 > > > Mar 27 08:10:57 localhost kernel: Pid: 3611, comm: obex-data-serve Not tainted 2.6.25-0.121.rc5.git4.fc9 #1 > > Mar 27 08:10:57 localhost kernel: [__lock_acquire+2287/3089] __lock_acquire+0x8ef/0xc11 > > Mar 27 08:10:57 localhost kernel: [sched_clock+8/11] ? sched_clock+0x8/0xb > > Mar 27 08:10:57 localhost kernel: [lock_acquire+106/144] lock_acquire+0x6a/0x90 > > Mar 27 08:10:57 localhost kernel: [<f8bd9321>] ? l2cap_sock_bind+0x29/0x108 [l2cap] > > Mar 27 08:10:57 localhost kernel: [lock_sock_nested+182/198] lock_sock_nested+0xb6/0xc6 > > Mar 27 08:10:57 localhost kernel: [<f8bd9321>] ? l2cap_sock_bind+0x29/0x108 [l2cap] > > Mar 27 08:10:57 localhost kernel: [security_socket_post_create+22/27] ? security_socket_post_create+0x16/0x1b > > Mar 27 08:10:57 localhost kernel: [__sock_create+388/472] ? __sock_create+0x184/0x1d8 > > Mar 27 08:10:57 localhost kernel: [<f8bd9321>] l2cap_sock_bind+0x29/0x108 [l2cap] > > Mar 27 08:10:57 localhost kernel: [kernel_bind+10/13] kernel_bind+0xa/0xd > > Mar 27 08:10:57 localhost kernel: [<f8dad3d7>] rfcomm_dlc_open+0xc8/0x294 [rfcomm] > > Mar 27 08:10:57 localhost kernel: [lock_sock_nested+187/198] ? lock_sock_nested+0xbb/0xc6 > > Mar 27 08:10:57 localhost kernel: [<f8dae18c>] rfcomm_sock_connect+0x8b/0xc2 [rfcomm] > > Mar 27 08:10:57 localhost kernel: [sys_connect+96/125] sys_connect+0x60/0x7d > > Mar 27 08:10:57 localhost kernel: [__lock_acquire+1370/3089] ? __lock_acquire+0x55a/0xc11 > > Mar 27 08:10:57 localhost kernel: [sys_socketcall+140/392] sys_socketcall+0x8c/0x188 > > Mar 27 08:10:57 localhost kernel: [syscall_call+7/11] syscall_call+0x7/0xb --- Signed-off-by: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET]: Make socket creation namespace safe.Eric W. Biederman
This patch passes in the namespace a new socket should be created in and has the socket code do the appropriate reference counting. By virtue of this all socket create methods are touched. In addition the socket create methods are modified so that they will fail if you attempt to create a socket in a non-default network namespace. Failing if we attempt to create a socket outside of the default network namespace ensures that as we incrementally make the network stack network namespace aware we will not export functionality that someone has not audited and made certain is network namespace safe. Allowing us to partially enable network namespaces before all of the exotic protocols are supported. Any protocol layers I have missed will fail to compile because I now pass an extra parameter into the socket creation code. [ Integrated AF_IUCV build fixes from Andrew Morton... -DaveM ] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25[SK_BUFF]: Introduce skb_reset_transport_header(skb)Arnaldo Carvalho de Melo
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can later turn skb->h.raw into a offset, reducing the size of struct sk_buff in 64bit land while possibly keeping it as a pointer on 32bit. This one touches just the most simple cases: skb->h.raw = skb->data; skb->h.raw = {skb_push|[__]skb_pull}() The next ones will handle the slightly more "complex" cases. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-02-10[NET] BLUETOOTH: Fix whitespace errors.YOSHIFUJI Hideaki
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2006-10-15[Bluetooth] Add locking for bt_proto array manipulationMarcel Holtmann
The bt_proto array needs to be protected by some kind of locking to prevent a race condition between bt_sock_create and bt_sock_register. And in addition all calls to sk_alloc need to be made GFP_ATOMIC now. Signed-off-by: Masatake YAMATO <jet@gyve.org> Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-10-15[Bluetooth] Support concurrent connect requestsMarcel Holtmann
Most Bluetooth chips don't support concurrent connect requests, because this would involve a multiple baseband page with only one radio. In the case an upper layer like L2CAP requests a concurrent connect these chips return the error "Command Disallowed" for the second request. If this happens it the responsibility of the Bluetooth core to queue the request and try again after the previous connect attempt has been completed. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-09-28[Bluetooth] Return EINPROGRESS for non-blocking socket callsMarcel Holtmann
In case of non-blocking socket calls we should return EINPROGRESS and not EAGAIN. Signed-off-by: Ulisses Furquim <ulissesf@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-07-03[Bluetooth] Add platform device for virtual and serial devicesMarcel Holtmann
This patch adds a generic Bluetooth platform device that can be used as parent device by virtual and serial devices. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-07-03[Bluetooth] Add automatic sniff mode supportMarcel Holtmann
This patch introduces the automatic sniff mode feature. This allows the host to switch idle connections into sniff mode to safe power. Signed-off-by: Ulisses Furquim <ulissesf@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-03-25[PATCH] POLLRDHUP/EPOLLRDHUP handling for half-closed devices notificationsDavide Libenzi
Implement the half-closed devices notifiation, by adding a new POLLRDHUP (and its alias EPOLLRDHUP) bit to the existing poll/select sets. Since the existing POLLHUP handling, that does not report correctly half-closed devices, was feared to be changed, this implementation leaves the current POLLHUP reporting unchanged and simply add a new bit that is set in the few places where it makes sense. The same thing was discussed and conceptually agreed quite some time ago: http://lkml.org/lkml/2003/7/12/116 Since this new event bit is added to the existing Linux poll infrastruture, even the existing poll/select system calls will be able to use it. As far as the existing POLLHUP handling, the patch leaves it as is. The pollrdhup-2.6.16.rc5-0.10.diff defines the POLLRDHUP for all the existing archs and sets the bit in the six relevant files. The other attached diff is the simple change required to sys/epoll.h to add the EPOLLRDHUP definition. There is "a stupid program" to test POLLRDHUP delivery here: http://www.xmailserver.org/pollrdhup-test.c It tests poll(2), but since the delivery is same epoll(2) will work equally. Signed-off-by: Davide Libenzi <davidel@xmailserver.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Michael Kerrisk <mtk-manpages@gmx.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-03[NET]: Avoid atomic xchg() for non-error caseBenjamin LaHaise
It also looks like there were 2 places where the test on sk_err was missing from the event wait logic (in sk_stream_wait_connect and sk_stream_wait_memory), while the rest of the sock_error() users look to be doing the right thing. This version of the patch fixes those, and cleans up a few places that were testing ->sk_err directly. Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-11-08[Bluetooth]: Remove the usage of /proc completelyMarcel Holtmann
This patch removes all relics of the /proc usage from the Bluetooth subsystem core and its upper layers. All the previous information are now available via /sys/class/bluetooth through appropriate functions. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-10-28[Bluetooth] Make more functions staticMarcel Holtmann
This patch makes another bunch of functions static. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2005-04-25[PATCH] kill gratitious includes of major.h under net/*Al Viro
A lot of places in there are including major.h for no reason whatsoever. Removed. And yes, it still builds. The history of that stuff is often amusing. E.g. for net/core/sock.c the story looks so, as far as I've been able to reconstruct it: we used to need major.h in net/socket.c circa 1.1.early. In 1.1.13 that need had disappeared, along with register_chrdev(SOCKET_MAJOR, "socket", &net_fops) in sock_init(). Include had not. When 1.2 -> 1.3 reorg of net/* had moved a lot of stuff from net/socket.c to net/core/sock.c, this crap had followed... Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!