| Age | Commit message (Collapse) | Author |
|---|
|
This fixes a subtle bug in the calculation of the inter-packet gap and shows
that t_delta, as it is currently used, is not needed. And hence replaced.
The algorithm from RFC 3448, 4.6 below continually computes a send time t_nom,
which is initialised with the current time t_now; t_gran = 1E6 / HZ specifies
the scheduling granularity, s the packet size, and X the sending rate:
t_distance = t_nom - t_now; // in microseconds
t_delta = min(t_ipi, t_gran) / 2; // `delta' parameter in microseconds
if (t_distance >= t_delta) {
reschedule after (t_distance / 1000) milliseconds;
} else {
t_ipi = s / X; // inter-packet interval in usec
t_nom += t_ipi; // compute the next send time
send packet now;
}
1) Description of the bug
-------------------------
Rescheduling requires a conversion into milliseconds, due to this call chain:
* ccid3_hc_tx_send_packet() returns a timeout in milliseconds,
* this value is converted by msecs_to_jiffies() in dccp_write_xmit(),
* and finally used as jiffy-expires-value for sk_reset_timer().
The highest jiffy resolution with HZ=1000 is 1 millisecond, so using a higher
granularity does not make much sense here.
As a consequence, values of t_distance < 1000 are truncated to 0. This issue
has so far been resolved by using instead
if (t_distance >= t_delta + 1000)
reschedule after (t_distance / 1000) milliseconds;
The bug is in artificially inflating t_delta to t_delta' = t_delta + 1000. This
is unnecessarily large, a more adequate value is t_delta' = max(t_delta, 1000).
2) Consequences of using the corrected t_delta'
-----------------------------------------------
Since t_delta <= t_gran/2 = 10^6/(2*HZ), we have t_delta <= 1000 as long as
HZ >= 500. This means that t_delta' = max(1000, t_delta) is constant at 1000.
On the other hand, when using a coarse HZ value of HZ < 500, we have three
sub-cases that can all be reduced to using another constant of t_gran/2.
(a) The first case arises when t_ipi > t_gran. Here t_delta' is the constant
t_delta' = max(1000, t_gran/2) = t_gran/2.
(b) If t_ipi <= 2000 < t_gran = 10^6/HZ usec, then t_delta = t_ipi/2 <= 1000,
so that t_delta' = max(1000, t_delta) = 1000 < t_gran/2.
(c) If 2000 < t_ipi <= t_gran, we have t_delta' = max(t_delta, 1000) = t_ipi/2.
In the second and third cases we have delay values less than t_gran/2, which is
in the order of less than or equal to half a jiffy.
How these are treated depends on how fractions of a jiffy are handled: they
are either always rounded down to 0, or always rounded up to 1 jiffy (assuming
non-zero values). In both cases the error is on average in the order of 50%.
Thus we are not increasing the error when in the second/third case we replace
a value less than t_gran/2 with 0, by setting t_delta' to the constant t_gran/2.
3) Summary
----------
Fixing (1) and considering (2), the patch replaces t_delta with a constant,
whose value depends on CONFIG_HZ, changing the above algorithm to:
if (t_distance >= t_delta')
reschedule after (t_distance / 1000) milliseconds;
where t_delta' = 10^6/(2*HZ) if HZ < 500, and t_delta' = 1000 otherwise.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
The CCIDs are activated as last of the features, at the end of the handshake,
were the LISTEN state of the master socket is inherited into the server
state of the child socket. Thus, the only states visible to CCIDs now are
OPEN/PARTOPEN, and the closing states.
This allows to remove tests which were previously necessary to protect
against referencing a socket in the listening state (in CCID3), but which
now have become redundant.
As a further byproduct of enabling the CCIDs only after the connection has been
fully established, several typecast-initialisations of ccid3_hc_{rx,tx}_sock
can now be eliminated:
* the CCID is loaded, so it is not necessary to test if it is NULL,
* if it is possible to load a CCID and leave the private area NULL, then this
is a bug, which should crash loudly - and earlier,
* the test for state==OPEN || state==PARTOPEN now reduces only to the closing
phase (e.g. when the node has received an unexpected Reset).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
|
|
This patch does the same for CCID-3 as the previous patch for CCID-2:
s#ccid3hctx_##g;
s#ccid3hcrx_##g;
plus manual editing to retain consistency.
Please note: expanded the fields of the `struct tfrc_tx_info' in the hc_tx_sock,
since using short #define identifiers is not a good idea. The only place where
this embedded struct was used is ccid3_hc_tx_getsockopt().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This patch fixes two problems caused by the ubiquitous long "hctx->ccid2htx_"
and "hcrx->ccid2hcrx_" prefixes:
* code becomes hard to read;
* multiple-line statements are almost inevitable even for simple expressions;
The prefixes are not really necessary (compare with "struct tcp_sock").
There had been previous discussion of this on dccp@vger, but so far this was
not followed up (most people agreed that the prefixes are too long).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Leandro Melo de Sales <leandroal@gmail.com>
|
|
Two registration routines, for SP and NN features, are provided by this patch,
replacing a previous routine which was used for both feature types.
These are internal-only routines and therefore start with `__feat_register'.
It further exports the known limits of Sequence Window and Ack Ratio as symbolic
constants.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
|
|
The BUG_ON(w_tot == 0) only holds if there is no more than 1 loss interval in
the loss history. If there is only a single loss interval, the calc_i_mean()
routine need in fact not be called (RFC 3448, 6.3.1).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This sets the sysfs permissions so that root can toggle the `debug'
parameter available for nearly every DCCP module. This is useful
since there are various module inter-dependencies. The debug flag
can now be toggled at runtime using
echo 1 > /sys/module/dccp/parameters/dccp_debug
echo 1 > /sys/module/dccp_ccid2/parameters/ccid2_debug
echo 1 > /sys/module/dccp_ccid3/parameters/ccid3_debug
echo 1 > /sys/module/dccp_tfrc_lib/parameters/tfrc_debug
The last is not very useful yet, since no code at the moment calls
the tfrc_debug() macro.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This corrects an error in the computation of the open loss interval I_0:
* the interval length is (highest_seqno - start_seqno) + 1
* and not (highest_seqno - start_seqno).
This condition was not fully clear in RFC 3448, but reflects the current
revision state of rfc3448bis and is also consistent with RFC 4340, 6.1.1.
Further changes:
----------------
* variable renamed due to line length constraints;
* explicit typecast to `s64' to avoid implicit signed/unsigned casting.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This fixes a bug in the logic of the TFRC loss detection:
* new_loss_indicated() should not be called while a loss is pending;
* but the code allows this;
* thus, for two subsequent gaps in the sequence space, when loss_count
has not yet reached NDUPACK=3, the loss_count is falsely reduced to 1.
To avoid further and similar problems, all loss handling and loss detection is
now done inside tfrc_rx_hist_handle_loss(), using an appropriate routine to
track new losses.
Further changes:
----------------
* added a reminder that no RX history operations should be performed when
rx_handle_loss() has identified a (new) loss, since the function takes
care of packet reordering during loss detection;
* made tfrc_rx_hist_loss_pending() bool (thanks to an earlier suggestion
by Arnaldo);
* removed unused functions.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
RFC 4340, 7.7 specifies up to 6 bytes for the NDP Count option, whereas the code
is currently limited to up to 3 bytes. This seems to be a relict of an earlier
draft version and is brought up to date by the patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
The TFRC loss detection code used the wrong loss condition (RFC 4340, 7.7.1):
* the difference between sequence numbers s1 and s2 instead of
* the number of packets missing between s1 and s2 (one less than the distance).
Since this condition appears in many places of the code, it has been put into a
separate function, dccp_loss_free().
Further changes:
----------------
* tidied up incorrect typing (it was using `int' for u64/s64 types);
* optimised conditional statements for common case of non-reordered packets;
* rewrote comments/documentation to match the changes.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This fixes a bug in computing the inter-packet-interval t_ipi = s/X:
scaled_div32(a, b) uses u32 for b, but in "scaled_div32(s, X)" the type of the
sending rate `X' is u64. Since X is scaled by 2^6, this truncates rates greater
than 2^26 Bps (~537 Mbps).
Using full 64-bit division now.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This fixes a bug in the reverse lookup of p: given a value f(p), instead of p,
the function returned the smallest tabulated value f(p).
The smallest tabulated value of
10^6 * f(p) = sqrt(2*p/3) + 12 * sqrt(3*p/8) * (32 * p^3 + p)
for p=0.0001 is 8172.
Since this value is scaled by 10^6, the outcome of this bug is that a loss
of 8172/10^6 = 0.8172% was reported whenever the input was below the table
resolution of 0.01%.
This means that the value was over 80 times too high, resulting in large spikes
of the initial loss interval, thus unnecessarily reducing the throughput.
Also corrected the printk format (%u for u32).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
This patch fixes the following sparse warnings:
* nested min(max()) expression:
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__x' shadows an earlier one
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__y' shadows an earlier one
* Declaration of function prototypes in .c instead of .h file, resulting in
"should it be static?" warnings.
* Declared "struct dccpw" static (local to dccp_probe).
* Disabled dccp_delayed_ack() - not fully removed due to RFC 4340, 11.3
("Receivers SHOULD implement delayed acknowledgement timers ...").
* Used a different local variable name to avoid
net/dccp/ackvec.c:293:13: warning: symbol 'state' shadows an earlier one
net/dccp/ackvec.c:238:33: originally declared here
* Removed unused functions `dccp_ackvector_print' and `dccp_ackvec_print'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
In commit $(825de27d9e40b3117b29a79d412b7a4b78c5d815) (from 27th May, commit
message `dccp ccid-3: Fix "t_ipi explosion" bug'), the CCID-3 window counter
computation was fixed to cope with RTTs < 4 microseconds.
Such RTTs can be found e.g. when running CCID-3 over loopback. The fix removed
a check against RTT < 4, but introduced a divide-by-zero bug.
All steady-state RTTs in DCCP are filtered using dccp_sample_rtt(), which
ensures non-zero samples. However, a zero RTT is possible on initialisation,
when there is no RTT sample from the Request/Response exchange.
The fix is to use the fallback-RTT from RFC 4340, 3.4.
This is also better than just fixing update_win_count() since it allows other
parts of the code to always assume that the RTT is non-zero during the time
that the CCID is used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
The identification of this bug is thanks to Cheng Wei and Tomasz
Grobelny.
To avoid divide-by-zero, the implementation previously ignored RTTs
smaller than 4 microseconds when performing integer division RTT/4.
When the RTT reached a value less than 4 microseconds (as observed on
loopback), this prevented the Window Counter CCVal value from
advancing. As a result, the receiver stopped sending feedback. This in
turn caused non-ending expiries of the nofeedback timer at the sender,
so that the sending rate was progressively reduced until reaching the
minimum of one packet per 64 seconds.
The patch fixes this bug by handling integer division more
intelligently. Due to consistent use of dccp_sample_rtt(),
divide-by-zero-RTT is avoided.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Makes the intention of the nested min/max clear.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without a number of CONFIG.*DEBUG:
net/dccp/ccids/ccid3.c:
ccid3_hc_tx_update_x | -170
ccid3_hc_tx_packet_sent | -175
ccid3_hc_tx_packet_recv | -169
ccid3_hc_tx_no_feedback_timer | -192
ccid3_hc_tx_send_packet | -144
5 functions changed, 850 bytes removed, diff: -850
net/dccp/ccids/ccid3.c:
ccid3_update_send_interval | +191
1 function changed, 191 bytes added, diff: +191
net/dccp/ccids/ccid3.o:
6 functions changed, 191 bytes added, 850 bytes removed, diff: -659
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This implements the changes to the nofeedback timer handling suggested
in draft rfc3448bis00, section 4.4. In particular, these changes mean:
* better handling of the lossless case (p == 0)
* the timestamp for computing t_ld becomes obsolete
* much more recent document (RFC 3448 is almost 5 years old)
* concepts in rfc3448bis arose from a real, working implementation
(cf. sec. 12)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This implements the algorithm to update the allowed sending rate X upon
receiving feedback packets, as described in draft rfc3448bis, 4.2/4.3.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* the NO_SENT state is only triggered in bidirectional mode,
costing unnecessary processing.
* the TERM (terminating) state is irrelevant.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch
1) concentrates previously scattered computation of p_inv into one function;
2) removes the `p' element of the CCID3 RX sock (it is redundant);
3) makes the tfrc_rx_info structure standalone, only used on demand.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch makes the registration messages of CCID 2/3 a bit more
informative: instead of repeating the CCID number as currently done,
"CCID: Registered CCID 2 (ccid2)" or
"CCID: Registered CCID 3 (ccid3)",
the descriptive names of the CCID's (from RFCs) are now used:
"CCID: Registered CCID 2 (TCP-like)" and
"CCID: Registered CCID 3 (TCP-Friendly Rate Control)".
To allow spaces in the name, the slab name string has been changed to
refer to the numeric CCID identifier, using the same format as before.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hooks up the TFRC Loss Interval database with CCID 3 packet reception.
In addition, it makes the CCID-specific computation of the first loss
interval (which requires access to all the guts of CCID3) local to ccid3.c.
The patch also fixes an omission in the DCCP code, that of a default /
fallback RTT value (defined in section 3.4 of RFC 4340 as 0.2 sec); while
at it, the upper bound of 4 seconds for an RTT sample has been reduced to
match the initial TCP RTO value of 3 seconds from[RFC 1122, 4.2.3.1].
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves two inlines back to packet_history.h: these are not private
to packet_history.c, but are needed by CCID3/4 to detect whether a new
loss is indicated, or whether a loss is already pending.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each time feedback is sent two lines are printed:
ccid3_hc_rx_send_feedback: client ... - entry
ccid3_hc_rx_send_feedback: Interval ...usec, X_recv=..., 1/p=...
The first line is redundant and thus removed.
Further, documentation of ccid3_hc_rx_sock (capitalisation) is made consistent.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A ringbuffer-based implementation of loss interval history is easier to
maintain, allocate, and update.
The `swap' routine to keep the RX history sorted is due to and was written
by Arnaldo Carvalho de Melo, simplifying an earlier macro-based variant.
Details:
* access to the Loss Interval Records via macro wrappers (with safety checks);
* simplified, on-demand allocation of entries (no extra memory consumption on
lossless links); cache allocation is local to the module / exported as service;
* provision of RFC-compliant algorithm to re-compute average loss interval;
* provision of comprehensive, new loss detection algorithm
- support for all cases of loss, including re-ordered/duplicate packets;
- waiting for NDUPACK=3 packets to fill the hole;
- updating loss records when a late-arriving packet fills a hole.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves the inlines (which were previously declared as macros) back into
packet_history.h since the loss detection code needs to be able to read entries
from the RX history in order to create the relevant loss entries: it needs at
least tfrc_rx_hist_loss_prev() and tfrc_rx_hist_last_rcv(), which in turn
require the definition of the other inlines (macros).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This separates RX/TX initialisation and puts all packet history / loss intervals
initialisation into tfrc.c.
The organisation is uniform: slab declaration -> {rx,tx}_init() -> {rx,tx}_exit()
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moved up the comment "Receiver routines" above the first occurrence of
RX history routines.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Credit here goes to Gerrit Renker, that provided the initial implementation for
this new codebase.
I modified it just to try to make it closer to the existing API, renaming some
functions, add namespacing and fix one bug where the tfrc_rx_hist_alloc was not
freeing the allocated ring entries on the error path.
Original changeset comment from Gerrit:
-----------
This provides a new, self-contained and generic RX history service for TFRC
based protocols.
Details:
* new data structure, initialisation and cleanup routines;
* allocation of dccp_rx_hist entries local to packet_history.c,
as a service exported by the dccp_tfrc_lib module.
* interface to automatically track highest-received seqno;
* receiver-based RTT estimation (needed for instance by RFC 3448, 6.3.1);
* a generic function to test for `data packets' as per RFC 4340, sec. 7.7.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the sender sets window counters [RFC 4342, sections 5 and 8.1].
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is in preparation for merging the new rx history code written by Gerrit Renker.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is in preparation for merging the new rx history code written by Gerrit Renker.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the tfrc_lib module in the following manner:
(1) a dedicated tfrc source file to call the packet history &
loss interval init/exit functions.
(2) a dedicated tfrc_pr_debug macro with toggle switch `tfrc_debug'.
Commiter note: renamed tfrc_module.c to tfrc.c, and made CONFIG_IP_DCCP_CCID3
select IP_DCCP_TFRC_LIB.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on a previous patch by Gerrit Renker.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch was based on another made by Gerrit Renker, his changelog was:
------------------------------------------------------
The patch set migrates TFRC TX history to a singly-linked list.
The details are:
* use of a consistent naming scheme (all TFRC functions now begin with `tfrc_');
* allocation and cleanup are taken care of internally;
* provision of a lookup function, which is used by the CCID TX infrastructure
to determine the time a packet was sent (in turn used for RTT sampling);
* integration of the new interface with the present use in CCID3.
------------------------------------------------------
Simplifications I did:
. removing the tfrc_tx_hist_head that had a pointer to the list head and
another for the slabcache.
. No need for creating a slabcache for each CCID that wants to use the TFRC
tx history routines, create a single slabcache when the dccp_tfrc_lib module
init routine is called.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes a comment which identifies an `issue' with dccp_write_xmit() where there is none.
The comment assumes it is possible that a packet is sent between the calls to
ccid_hc_tx_send_packet(),
dccp_transmit_skb(),
ccid_hc_tx_packet_sent()
(in the above order) in dccp_write_xmit().
I think that this is impossible, since dccp_write_xmit() is always called under lock:
* when called as dccp_write_xmit(sk, 1) from dccp_send_close(), the socket is locked
(see code comment above dccp_send_close());
* when called as dccp_write_xmit(sk, 0) from dccp_send_msg(), it is after lock_sock() has been called;
* when called as dccp_write_xmit(sk, 0) from dccp_write_xmit_timer(), bh_lock_sock() has been called
and the if/else statement has made sure that sk_lock.owner is not set;
* there are no other places where dccp_write_xmit() is called.
Furthermore, the debug statement for printing the sequence number of the packet just sent has been
removed, since the entire list is being printed anyway and so the entry of that number appears last.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code used two different variables to count Acks, one of them redundant.
This patch reduces the number of Ack counters to one.
The type of the Ack counter has also been changed to u32 (twice the range of int);
and the variable has been renamed into `packets_acked' - for consistency with
RFC 3465 (and similarly named variables are used by TCP and SCTP).
Lastly, a slightly less aggressive `maxincr' increment is used (for even Ack Ratios,
maxincr was Ack Ratio/2 + 1 instead of Ack Ratio/2).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes the synchronisation variable `ccid2hctx_sendwait', which is set to 1
when the CCID2 sender may send a new packet, and which is set to 0 otherwise
The variable is redundant, since it is only used in combination with the hc_tx_send_packet/
hc_tx_packet_sent function pair. Both functions are called under socket lock, so the
following happens when the CCID2 may send a new packet:
* it sets sendwait = 1 in tx_send_packet and returns 0;
* the subsequent call to tx_packet_sent clears the sendwait flag;
* since tx_send_packet returns 0 if and only if sendwait == 1, the BUG_ON condition
in tx_packet_sent is never satisfied, since that function is never called when
tx_send_packet returns a value different from 0 (cf. dccp_write_xmit);
* the call to tx_packet_sent clears the flag so that the condition "!sendwait" is
true the next time tx_packet_sent is called.
In other words, it is sufficient to just return 0 / not-0 to synchronise tx_send_packet
and tx_packet_sent -- which is what the patch does.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reduces the amount of redundant debugging messages:
* pipe/cwnd are printed in both tx_send_packet() and tx_packet_sent().
Both functions are called immediately after one another, so one occurrence is sufficient.
* Since tx_packet_sent() prints pipe/cwnd already, the second printk for pipe is redundant.
* In tx_packet_sent() the check_sanity function is called twice (at the begin and at the end).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ccid2_change_pipe only does an assignment. This patch simplifies the code by
replacing the function with the assignment it performs.
Furthermore, the type of pipe is promoted from `signed' to unsigned (increasing the range).
As a result, a BUG_ON test for negative values now becomes obsolete (for safety not removed,
but replaced with a less annoying `DCCP_BUG').
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current function ccid2_change_cwnd in effect makes only an assignment, as
the test whether cwnd has reached 0 is only required when cwnd is halved.
This patch simplifies the code by replacing the function with the assignment
it performs.
Furthermore, since ssthresh derives from cwnd and appears in many assignments and
comparisons, the type of ssthresh has also been changed to match that of cwnd.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This replaces the field member `numdupack', which was used as a read-only
constant in the code, with a #define.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes a variable `ccid2hctx_sent' which is incremented but
never referenced/read (i.e., dead code).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This comments out a problematic section comprising a half-finished algorithm:
- The variable `ccid2hctx_ackloss' is never initialised to a value different from 0 and
hence in fact is a read-only constant.
- The `arsent' variable counts packets other than Acks (it is incremented for every packet),
and there is no test for Ack Loss.
- The concept of counting Acks as such leads to a complex calculation, and the calculation
at the moment is inconsistent with this concept.
The problem is that the number of Acks - rather than the number of windows - is counted,
which leads to a complex (cubic/quadratic) expression - this is not even implemented.
In its current state, the commented-out algorithm interfers with normal processing by
changing Ack Ratio incorrectly, and at the wrong times.
A new algorithm is necessary, which will not necessarily use the same variables as used by
the unfinished one; hence the old variables have been removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
