aboutsummaryrefslogtreecommitdiff
path: root/net/dsa/slave.c
AgeCommit message (Collapse)Author
2008-11-11Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/message/fusion/mptlan.c drivers/net/sfc/ethtool.c net/mac80211/debugfs_sta.c
2008-11-10dsa: fix master interface allmulti/promisc handlingLennert Buytenhek
Before commit b6c40d68ff6498b7f63ddf97cf0aa818d748dee7 ("net: only invoke dev->change_rx_flags when device is UP"), the dsa driver could sort-of get away with only fiddling with the master interface's allmulti/promisc counts in ->change_rx_flags() and not touching them in ->open() or ->stop(). After this commit (note that it was merged almost simultaneously with the dsa patches, which is why this wasn't caught initially), the breakage that was already there became more apparent. Since it makes no sense to keep the master interface's allmulti or promisc count pinned for a slave interface that is down, copy the vlan driver's sync logic (which does exactly what we want) over to dsa to fix this. Bug report from Dirk Teurlings <dirk@upexia.nl> and Peter van Valderen <linux@ddcrew.com>. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Tested-by: Peter van Valderen <linux@ddcrew.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10net: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers
Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08dsa: add support for Trailer tagging formatLennert Buytenhek
This adds support for the Trailer switch tagging format. This is another tagging that doesn't explicitly mark tagged packets with a distinct ethertype, so that we need to add a similar hack in the receive path as for the Original DSA tagging format. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08dsa: add support for original DSA tagging formatLennert Buytenhek
Most of the DSA switches currently in the field do not support the Ethertype DSA tagging format that one of the previous patches added support for, but only the original DSA tagging format. The original DSA tagging format carries the same information as the Ethertype DSA tagging format, but with the difference that it does not have an ethertype field. In other words, when receiving a packet that is tagged with an original DSA tag, there is no way of telling in eth_type_trans() that this packet is in fact a DSA-tagged packet. This patch adds a hook into eth_type_trans() which is only compiled in if support for a switch chip that doesn't support Ethertype DSA is selected, and which checks whether there is a DSA switch driver instance attached to this network device which uses the old tag format. If so, it sets the protocol field to ETH_P_DSA without looking at the packet, so that the packet ends up in the right place. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08net: Distributed Switch Architecture protocol supportLennert Buytenhek
Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>