aboutsummaryrefslogtreecommitdiff
path: root/net/mac80211/ieee80211_i.h
AgeCommit message (Collapse)Author
2009-09-01wireless: convert drivers to netdev_tx_tStephen Hemminger
Mostly just simple conversions: * ray_cs had bogus return of NET_TX_LOCKED but driver was not using NETIF_F_LLTX * hostap and ipw2x00 had some code that returned value from a called function that also had to change to return netdev_tx_t Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28mac80211: remove tasklet enable/disableJohannes Berg
Due to the way the tasklets work in mac80211 there's no need to ever disable them. However, we need to clear the pending packets when taking down the last interface because otherwise the tx_pending_tasklet might be queued if the driver mucks with the queues (which it shouldn't). I've had a situation occasionally with ar9170 in which ksoftirq was using 100% CPU time because a disabled tasklet was scheduled, and I think that was due to ar9170 receiving a packet while the tasklet was disabled. That's strange and it really should not do that for other reasons, but there's no need to waste that much CPU time over it, it should just warn instead. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28mac80211: fix configure_filter invocation after stopJohannes Berg
Since configure_filter can sleep now, any multicast configuration needed to be postponed to a work struct. This, however, lead to a problem that we could queue the work, stop the device and then afterwards invoke configure_filter which may lead to driver hangs and is a bug. To fix this, we can just cancel the filter work since it's unnecessary to do after stopping the hw. Since there are various places that call drv_stop, and two of them do very similar things, the code for them can be put into a shared function at the same time. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Reported-by: Lennert Buytenhek <buytenh@wantstofly.org> Tested-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28mac80211: Update mesh config IE to 11s draft 3.02Javier Cardona
The mesh config information element has changed significantly since draft 1.08 This patch brings it up to date. Thanks to Sam Leffler and Rui Paulo for identifying this. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20mac80211: New stat counters for multicast and unicast forwarded framesDaniel Walker
This expands on the current fwded_frames stat counter which should be equal to the total of these two new counters. The new counters are called "fwded_mcast" and "fwded_unicast". Signed-off-by: Daniel Walker <dwalker@fifo99.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20mac80211: allow configure_filter callback to sleepJohannes Berg
Over time, a whole bunch of drivers have come up with their own scheme to delay the configure_filter operation to a workqueue. To be able to simplify things, allow configure_filter to sleep, and add a new prepare_multicast callback that drivers that need the multicast address list implement. This new callback must be atomic, but most drivers either don't care or just calculate a hash which can be done atomically and then uploaded to the hardware non-atomically. A cursory look suggests that at76c50x-usb, ar9170, mwl8k (which is actually very broken now), rt2x00, wl1251, wl1271 and zd1211 should make use of this new capability. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14mac80211: Move mpath and mpp growth to mesh workqueue.Javier Cardona
This prevents calling rcu_synchronize from within the tx path by moving the table growth code to the mesh workqueue. Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and declare them static. Also, re-enable mesh in Kconfig and update the configuration description. Signed-off-by: Javier Cardona <javier@cozybit.com> Tested-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14cfg80211: fix alignment problem in scan requestJohannes Berg
The memory layout for scan requests was rather wrong, we put the scan SSIDs before the channels which could lead to the channel pointers being unaligned in memory. It turns out that using a pointer to the channel array isn't necessary anyway since we can embed a zero-length array into the struct. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14nl80211: add generation number to all dumpsJohannes Berg
In order for userspace to be able to figure out whether it obtained a consistent snapshot of data or not when using netlink dumps, we need to have a generation number in each dump message that indicates whether the list has changed or not -- its value is arbitrary. This patch adds such a number to all dumps, this needs some mac80211 involvement to keep track of a generation number to start with when adding/removing mesh paths or stations. The wiphy and netdev lists can be fully handled within cfg80211, of course, but generation numbers need to be stored there as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14mac80211: stay authenticated after disassocJohannes Berg
After being disassociated by the AP, mac80211 currently reports this to cfg80211, and then goes to delete the association. That's fine, but cfg80211 assumes that it's still authenticated, however, mac80211 throws away all state. This fixes mac80211 to keep track of the authentication in that case so that cfg80211 can request a deauth or new association properly. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04mac80211: FIF_PSPOLL filter flagIgor Perminov
When an interface is configured in the AP mode, the mac80211 implementation doesn't inform the driver to receive PS Poll frames. It leads to inability to communicate with power-saving stations reliably. The FIF_CONTROL flag isn't passed by mac80211 to ieee80211_ops.configure_filter when an interface is in the AP mode. And it's ok, because we don't want to receive ACK frames and other control ones, but only PS Poll ones. This patch introduces the FIF_PSPOLL filter flag in addition to FIF_CONTROL, which means for the driver "pass PS Poll frames". This flag is passed to the driver: A) When an interface is configured in the AP mode. B) In all cases, when the FIF_CONTROL flag was passed earlier (in addition to it). Signed-off-by: Igor Perminov <igor.perminov@inbox.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04mac80211: Retry probe request few timesMaxim Levitsky
Retry 5 times (chosen arbitary ), before assuming that station is out of range. Fixes frequent disassociations while connected to weak, and sometimes even strong access points. Signed-off-by: Maxim Levitky <maximlevitsky@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04mac80211: redefine usage of the mac80211 workqueueLuis R. Rodriguez
The mac80211 workqueue exists to enable mac80211 and drivers to queue their own work on a single threaded workqueue. mac80211 takes care to flush the workqueue during suspend but we never really had requirements on drivers for how they should use the workqueue in consideration for suspend. We extend mac80211 to document how the mac80211 workqueue should be used, how it should not be used and finally move raw access to the workqueue to mac80211 only. Drivers and mac80211 use helpers to queue work onto the mac80211 workqueue: * ieee80211_queue_work() * ieee80211_queue_delayed_work() These helpers will now warn if mac80211 already completed its suspend cycle and someone is trying to queue work. mac80211 flushes the mac80211 workqueue prior to suspend a few times, but we haven't taken the care to ensure drivers won't add more work after suspend. To help with this we add a warning when someone tries to add work and mac80211 already completed the suspend cycle. Drivers should ensure they cancel any work or delayed work in the mac80211 stop() callback. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-29cfg80211: self-contained wext handling where possibleJohannes Berg
Finally! This is what you've all been waiting for! This patch makes cfg80211 take care of wext emulation _completely_ by itself, drivers that don't need things cfg80211 doesn't do yet don't even need to be aware of wireless extensions. This means we can also clean up mac80211's and iwm's Kconfig and make it possible to build them w/o wext now! RIP wext. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27mac80211: rename scan_state to next_scan_stateHelmut Schaa
Rename scan_state to next_scan_state to better reflect what it is used for. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27mac80211: implement basic background scanningHelmut Schaa
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us that we are currently on a different channel for scanning and cannot RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a software scan but we might as well be on the operating channel to RX/TX. While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL" is set when leaving the operating channel and unset when coming back. Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and "SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we need to leave the operating channel (send a nullfunc to the AP and stop the queues) and enter it again (send a nullfunc to the AP and start the queues again). Enhance the scan state "SCAN_DECISION" to switch back to the operating channel after each scanned channel. In the future it sould be simple to enhance the decision state to scan as much channels in a row as the qos latency allows us. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27mac80211: Replace {sw, hw}_scanning variables with a bitfieldHelmut Schaa
Use a bitfield to store the current scan mode instead of two boolean variables {sw,hw}_scanning. This patch does not introduce functional changes but allows us to enhance the scan flags later (for example for background scanning). Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27mac80211: introduce a new scan state "decision"Helmut Schaa
Introduce a new scan state "decision" which is entered after every completed scan operation and decides about the next steps. At first the decision is in any case to scan the next channel. This shouldn't introduce any functional changes. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24mac80211: remove master netdevJohannes Berg
With the internal 'pending' queue system in place, we can simply put packets there instead of pushing them off to the master dev, getting rid of the master interface completely. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24mac80211: monitor the connectionJohannes Berg
With the recent MLME rework I accidentally removed the connection monitoring code. In order to add it back, this patch will add new code to monitor both for beacon loss and for the connection actually working, with possibly separate triggers. When no unicast frames have been received from the AP for (currently) two seconds, we will send the AP a probe request. Also, when we don't see beacons from the AP for two seconds, we do the same (but those times need not be the same due to the way the code is now written). Additionally, clean up the parameters to the ieee80211_set_disassoc() function that I need here, those are all useless except sdata. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24cfg80211: rework key operationJohannes Berg
This reworks the key operation in cfg80211, and now only allows, from userspace, configuring keys (via nl80211) after the connection has been established (in managed mode), the IBSS been joined (in IBSS mode), at any time (in AP[_VLAN] modes) or never for all the other modes. In order to do shared key authentication correctly, it is now possible to give a WEP key to the AUTH command. To configure static WEP keys, these are given to the CONNECT or IBSS_JOIN command directly, for a userspace SME it is assumed it will configure it properly after the connection has been established. Since mac80211 used to check the default key in IBSS mode to see whether or not the network is protected, it needs an update in that area, as well as an update to make use of the WEP key passed to auth() for shared key authentication. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10cfg80211: fix lockingJohannes Berg
Over time, a lot of locking issues have crept into the smarts of cfg80211, so e.g. scan completion can race against a new scan, IBSS join can race against leaving an IBSS, etc. Introduce a new per-interface lock that protects most of the per-interface data that we need to keep track of, and sprinkle assertions about that lock everywhere. Some things now need to be offloaded to work structs so that we don't require being able to sleep in functions the drivers call. The exception to that are the MLME callbacks (rx_auth etc.) that currently only mac80211 calls because it was easier to do that there instead of in cfg80211, and future drivers implementing those calls will, if they ever exist, probably need to use a similar scheme like mac80211 anyway... In order to be able to handle _deauth and _disassoc properly, introduce a cookie passed to it that will determine locking requirements. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: rework MLME for multiple authenticationsJohannes Berg
Sit tight. This shakes up the world as you know it. Let go of your spaghetti tongs, they will no longer be required, the horrible statemachine in net/mac80211/mlme.c is no more... With the cfg80211 SME mac80211 now has much less to keep track of, but, on the other hand, for FT it needs to be able to keep track of at least one authentication being in progress while associated. So convert from a single state machine to having small ones for all the different things we need to do. For real FT it will still need work wrt. PS, but this should be a good step. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: remove dead code from mlmeJohannes Berg
The ap_capab and last_probe struct members are unused. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: remove dead code, clean upJohannes Berg
With mac80211 now always controlled by an external SME, a lot of code is dead -- SSID, BSSID, channel selection is always done externally, etc. Additionally, rename IEEE80211_STA_TKIP_WEP_USED to IEEE80211_STA_DISABLE_11N and clean up the code a bit. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: remove auth algorithm retryJohannes Berg
The automatic auth algorithm issue is now solved in cfg80211, so mac80211 no longer needs code to try different algorithms -- just using whatever cfg80211 asked for is good. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: remove an unused function declarationJohannes Berg
The ieee80211_scan_results function hasn't existed for a long time now, so its declaration should be removed as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10cfg80211: use proper allocation flagsJohannes Berg
Instead of hardcoding GFP_ATOMIC everywhere, add a new function parameter that gets the flags from the caller. Obviously then I need to update all callers (all of them in mac80211), and it turns out that now it's ok to use GFP_KERNEL in almost all places. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: push rx status into skb->cbJohannes Berg
Within mac80211, we often need to copy the rx status into skb->cb. This is wasteful, as drivers could be building it in there to start with. This patch changes the API so that drivers are expected to pass the RX status in skb->cb, now accessible as IEEE80211_SKB_RXCB(skb). It also updates all drivers to pass the rx status in there, but only by making them memcpy() it into place before the call to the receive function (ieee80211_rx(_irqsafe)). Each driver can now be optimised on its own schedule. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-06-15mac80211: disconnect when user changes channelJohannes Berg
If we do not disconnect when a channel switch is requested, we end up eventually detection beacon loss from the AP and then disconnecting, without ever really telling the AP, so we might just as well disconnect right away. Additionally, this fixes a problem with iwlwifi where the driver will clear some internal state on channel changes like this and then get confused when we actually go clear that state from mac80211. It may look like this patch drops the no-IBSS check, but that is already handled by cfg80211 in the wext handler it provides for IBSS (cfg80211_ibss_wext_siwfreq). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-06-15mac80211: add queue debugfs fileJohannes Berg
I suspect that some driver bugs can cause queues to be stopped while they shouldn't be, but it's hard to find out whether that is the case or not without having any visible information about the queues. This adds a file to debugfs that allows us to see the queues' statuses. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-06-10mac80211: do not pass PS frames out of mac80211 againJohannes Berg
In order to handle powersave frames properly we had needed to pass these out to the device queues again, and introduce the skb->requeue bit. This, however, also has unnecessary overhead by needing to 'clean up' already tried frames, and this clean-up code is also buggy when software encryption is used. Instead of sending the frames via the master netdev queue again, simply put them into the pending queue. This also fixes a problem where frames for that particular station could be reordered when some were still on the software queues and older ones are re-injected into the software queue after them. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-22wireless: move some utility functions from mac80211 to cfg80211Zhu Yi
The patch moves some utility functions from mac80211 to cfg80211. Because these functions are doing generic 802.11 operations so they are not mac80211 specific. The moving allows some fullmac drivers to be also benefit from these utility functions. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20mac80211: cancel/restart all timers across suspend/resumeJohannes Berg
We forgot to cancel all timers in mac80211 when suspending. In particular we forgot to deal with some things that can cause hardware reconfiguration -- while it is down. While at it we go ahead and add a warning in ieee80211_sta_work() if its run while the suspend->resume cycle is in effect. This should not happen and if it does it would indicate there is a bug lurking in either mac80211 or mac80211 drivers. With this now wpa_supplicant doesn't blink when I go to suspend and resume where as before there where issues with some timers running during the suspend->resume cycle. This caused a lot of incorrect assumptions and would at times bring back the device in an incoherent, but mostly recoverable, state. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20mac80211: move channel switch codeJohannes Berg
The channel switch code is currently in the spectrum management file, where arguably it belongs. However, it is for managed mode only and uses the structures for that mode only so having it in a more generic file can be confusing. Additionally, my next patch gets simpler with the code here. When/if we ever implement this for IBSS or mesh then we will need to rework the structures it uses anyway at which point we could move the code back. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20mac80211/cfg80211: move wiphy specific debugfs entries to cfg80211Luis R. Rodriguez
This moves the cfg80211 specific stuff to new cfg80211 debugfs entries. Non-mac80211 will also get these entries now. There were only 4 which we take: rts_threshold fragmentation_threshold short_retry_limit long_retry_limit Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-13mac80211: make noack test availableJohannes Berg
There's this internal wifi_wme_noack_test variable that we use to set the QoS control if set. For one, it is unlikely that it is set. Secondly, if set it needs to influence the IEEE80211_TX_CTL_NO_ACK TX control flag, and finally we should also be able to set it at all, so make it available in debugfs. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-13nl80211: Add IEEE 802.1X PAE control for station modeJouni Malinen
Add a new NL80211_ATTR_CONTROL_PORT flag for NL80211_CMD_ASSOCIATE to allow user space to indicate that it will control the IEEE 802.1X port in station mode. Previously, mac80211 was always marking the port authorized in station mode. This was enough when drop_unencrypted flag was set. However, drop_unencrypted can currently be controlled only with WEXT and the current nl80211 design does not allow fully secure configuration. Fix this by providing a mechanism for user space to control the IEEE 802.1X port in station mode (i.e., do the same that we are already doing in AP mode). Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-11mac80211: properly track HT operation_modeJohannes Berg
When we disassociate, we set the channel to non-HT which obviously invalidates any ht_operation_mode setting. But when we then associate with the next AP again, we might still have the ht_operation_mode from the previous AP cached and fail to configure the hardware with the new (but unchanged) operation mode. This patch fixes it by separately tracking whether our cache is valid. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-06mac80211: tell driver when idleJohannes Berg
When we aren't doing anything in mac80211, we can turn off much of the hardware, depending on the driver/hw. Not doing anything, aka being idle, means: * no monitor interfaces * no AP/mesh/wds interfaces * any station interfaces are in DISABLED state * any IBSS interfaces aren't trying to be in a network * we aren't trying to scan By creating a new function that verifies these conditions and calling it at strategic points where the states of those conditions change, we can easily make mac80211 tell the driver when we are idle to save power. Additionally, this fixes a small quirk where a recalculated powersave state is passed to the driver even if the hardware is about to stopped completely. This patch intentionally doesn't touch radio_enabled because that is currently implemented to be a soft rfkill which is inappropriate here when we need to be able to wake up with low latency. One thing I'm not entirely sure about is this: phy0: device no longer idle - in use wlan0: direct probe to AP 00:11:24:91:07:4d try 1 wlan0 direct probe responded wlan0: authenticate with AP 00:11:24:91:07:4d wlan0: authenticated > phy0: device now idle > phy0: device no longer idle - in use wlan0: associate with AP 00:11:24:91:07:4d wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1) wlan0: associated Is it appropriate to go into idle state for a short time when we have just authenticated, but not associated yet? This happens only with the userspace SME, because we cannot really know how long it will wait before asking us to associate. Would going idle after a short timeout be more appropriate? We may need to revisit this, depending on what happens. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-06mac80211: fix probe response processingJohannes Berg
Due to the use of a _REQ_DIRECT_PROBE bit, which is unnecessary (and I wonder why it was done that way), an interesting situation can arise: 1) we try to probe an access point 2) the AP doesn't response in time 3) we tell userspace that we gave up 4) the AP suddenly responds 5) we auth/assoc with the AP I've seen 4) happen in testing with hostapd SIGSTOPped, and when SIGCONTinued it processes the probe requests that came in and send responses. But 5) is not supposed to happen after we tell everybody we've given up on the AP. To fix this, remove the _REQ_DIRECT_PROBE request bit, and process probe responses when we're in the relevant MLME state, namely IEEE80211_STA_MLME_DIRECT_PROBE. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-06mac80211: unify config_interface and bss_info_changedJohannes Berg
The config_interface method is a little strange, it contains the BSSID and beacon updates, while bss_info_changed contains most other BSS information for each interface. This patch removes config_interface and rolls all the information it previously passed to drivers into bss_info_changed. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-06mac80211: fix scan races and rework scanningJohannes Berg
There are some places marked /* XXX maybe racy? */ and they really are racy because there's no locking. This patch reworks much of the scan code, and introduces proper locking for the scan request as well as the internal scanning (which is necessary for IBSS/managed modes). Helper functions are added to call the scanning code whenever necessary. The scan deferring is changed to simply queue the scanning work instead of trying to start the scan in place, the scanning work will then take care of the rest. Also, currently when internal scans are requested for an interface that is trying to associate, we reject such scans. This was not intended, the mlme code has provisions to scan twice when it can't find the BSS to associate with right away; this has never worked properly. Fix this by not rejecting internal scan requests for an interface that is associating. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: validate TIM IE length (redux)Johannes Berg
The TIM IE must not be shorter than 4 bytes, so verify that when parsing it and use the proper type. To ease that adjust struct ieee80211_tim_ie to have a virtual bitmap of size at least 1. Also check that the TIM IE is actually present before trying to parse it! Because other people may need the function, make it a static inline in ieee80211.h. (The original "mac80211: validate TIM IE length" was a minimal fix for 2.6.30. This purports to be the full, correct fix. -- JWL) Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22nl80211: Add set/get for frag/rts threshold and retry limitsJouni Malinen
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and retry limits. Since these values are stored in struct wiphy, remove the local copy from mac80211 where feasible (frag & rts threshold). The retry limits are currently needed in struct ieee80211_conf, but these could be eventually removed since the driver should have access to the values in struct wiphy. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22cfg80211: clean up includesJohannes Berg
Trying to separate header files into net/wireless.h and net/cfg80211.h has been a source of confusion. Remove net/wireless.h (because there also is the linux/wireless.h) and subsume everything into net/cfg80211.h -- except the definitions for regulatory structures which get moved to a new header net/regulatory.h. The "new" net/cfg80211.h is now divided into sections. There are no real changes in this patch but code shuffling and some very minor documentation fixes. I have also, to make things reflect reality, put in a copyright line for Luis to net/regulatory.h since that is probably exclusively written by him but was formerly in a file that only had my copyright line. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: convert to cfg80211 IBSS APIJohannes Berg
This converts mac80211 to the new cfg80211 IBSS API, the wext handling functions are called where appropriate. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: implement beacon filtering in softwareJohannes Berg
Regardless of whether the hardware implements beacon filtering, there's no need to process all beacons in software all the time throughout the stack (mac80211 does a lot, then cfg80211, then in the future possibly userspace). This patch implements the "best possible" beacon filtering in mac80211. "Best possible" means that it can look for changes in all requested information elements, and distinguish vendor IEs by their OUI. In the future, we will add nl80211 API for userspace to request information elements and vendor IE OUIs to watch -- drivers can then implement the best they can do while software implements it fully. It is unclear whether or not this actually saves CPU time, but the data is all in the cache already so it should be fairly cheap. The additional _testing_, however, has great benefit; Without this, and on hardware that doesn't implement beacon filtering, wrong assumptions about, for example, scan result updates could quickly creep into code. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: disable powersave if pm_qos asks for low latencyJohannes Berg
When an application asks for a latency lower than the beacon interval there's nothing we can do -- we need to stay awake and not have the AP buffer frames for us. Add code to automatically calculate this constraint in mac80211 so drivers need not concern themselves with it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: improve powersave implementationJohannes Berg
When you have multiple virtual interfaces the current implementation requires setting them up properly from userspace, which is undesirable when we want to default to power save mode. Keep track of powersave requested from userspace per managed mode interface, and only enable powersave globally when exactly one managed mode interface is active and has powersave turned on. Second, only start the dynPS timer when PS is turned on, and properly turn it off when PS is turned off. Third, fix the scan_sdata abuse in the dynps code. Finally, also reorder the code and refactor the code that enables PS or the dynps timer instead of having it copied in two places. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>