aboutsummaryrefslogtreecommitdiff
path: root/net/mac80211/rc80211_simple.c
AgeCommit message (Collapse)Author
2007-11-10mac80211: make simple rate control algorithm built-inJohannes Berg
Too frequently people do not have module autoloading enabled or fail to install the rate control module correctly, hence their hardware probing fails due to no rate control algorithm being available. This makes the 'simple' algorithm built into the mac80211 module unless EMBEDDED is enabled in which case it can be disabled (eg. if the wanted driver requires another rate control algorithm.) Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[NET]: Introduce and use print_mac() and DECLARE_MAC_BUF()Joe Perches
This is nicer than the MAC_FMT stuff. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[MAC80211]: remove unused ioctls (2)Johannes Berg
The ioctls * PRISM2_PARAM_STA_ANTENNA_SEL * PRISM2_PARAM_TX_POWER_REDUCTION * PRISM2_PARAM_DEFAULT_WEP_ONLY are not used by hostapd or wpa_supplicant. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-09-25[PATCH] mac80211: fix initialisation when built-inJohannes Berg
When mac80211 is built into the kernel it needs to init earlier so that device registrations are run after it has initialised. The same applies to rate control algorithms. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-07-12[PATCH] mac80211: kill rate control ioctlsJohannes Berg
These aren't used anywhere (hostapd, wpa_supplicant) and until we have a proper interface to the rate control algorithms they don't make much sense either since e.g. rc80211_lowest won't honour them. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-07-10[MAC80211]: Set low initial rate in rc80211_simpleLarry Finger
The initial rate for STA's using rc80211_simple is set to the last rate in the rate table. For situations for which the signal is weak, the rate may be too high for authentication and association. Although the rc80211_simple module will adjust the speed, the response may not be fast enough for a successful connection. This modification sets the initial rate to the lowest supported value. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05[MAC80211]: Add debugfs attributes.Jiri Benc
Export various mac80211 internal variables through debugfs. Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05[MAC80211]: Add mac80211 wireless stack.Jiri Benc
Add mac80211, the IEEE 802.11 software MAC layer. Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>