| Age | Commit message (Collapse) | Author |
|---|
|
To make U-APSD client mode effective, we must not wake up from dynamic power
save when transmitting frames. So if dynamic power save is enabled, it needs
check the queue the transmitted packet is in and decide if we need to wake
up or not.
In a perfect world, where all packets would have correct QoS tags, U-APSD
enabled queues should not trigger wakeup from power save. But in the real
world, where very few packets have correct QoS tags, this won't work. For
example, if only voip class has U-APSD enabled and we send a packet in voip
class, but the packets we receive are in best effort class, we would receive
the packets with the legacy power save method. And that would increase
latencies too much from a voip application point of view.
The workaround is to enable U-APSD for all qeueus and still use dynamic ps
wakeup for all other queues except voip. That way we can still save power
with a voip application and not sacrifice latency. Normal traffic (in
background, best effort or video class) would still trigger wakeup from
dynamic power save.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently dynamic ps check is in ieee80211_xmit(), but it's cleaner
to have a separate tx handler for this. Also this is a prerequisite for
U-APSD client mode which needs to know the queue frame is in.
Also need_dynamic_ps() function is embedded to the tx handler.
No functional changes expect that the code is run in a later phase than
originally.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Because it's not yet decided how to configure which queues are U-APSD
enabled, add a debugfs interface for testing purposes.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add Unscheduled Automatic Power-Save Delivery (U-APSD) client support. The
idea is that the data frames from the client trigger AP to send the buffered
frames with ACs which have U-APSD enabled. This decreases latency and makes it
possible to save even more power.
Driver needs to use IEEE80211_HW_UAPSD to enable the feature. The current
implementation assumes that firmware takes care of the wakeup and
hardware needing IEEE80211_HW_PS_NULLFUNC_STACK is not yet supported.
Tested with wl1251 on a Nokia N900 and Cisco Aironet 1231G AP and running
various test traffic with ping.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The type argument to DEBUGFS_ADD() isn't used
and can be removed, it's around from before
the conversion to debugfs_remove_recursive().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since commit "mwl8k: handle station database update for AP's sta entry
via ->sta_notify()", mwl8k every now and then gets a command timeout
when ifconfig'ing a STA interface down. This turns out to be due to
mwl8k_stop() being called while the work queue item that was scheduled
by mwl8k_sta_notify() to remove the STA entry for the associated AP is
still queued, and the former disables interrupts so that when the
latter eventually runs, a command completion interrupt is never seen.
Fix this by changing ieee80211_stop_device() so that the workqueue is
flushed before drv_stop() is called, instead of doing it the other way
around as is done now. (As ->stop() is allowed to sleep, there isn't
any reason for drivers to queue work from within it.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
sparse pointed out that I made a mistake converting
the return value of ieee80211_assoc_success to bool,
this place should return false instead of one of the
enum values (which would be true).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If frames are transmitted on 4-addr ap vlan interfaces with no station,
they end up being transmitted unencrypted, even if the ap interface
uses WPA. This patch add some sanity checking to make sure that this
does not happen.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since the per-vif station changes, sta_info_get on the ap sdata no
longer returns entries for stations on ap vlans. This causes issues
with hostapd, which currently always passes the ap interface name to
nl80211 calls. This patch provides bug compatibility with the earlier
versions until hostapd is fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To detect incoming 4-addr stations, hostapd needs to receive a 4-addr
data frame from the remote station, so that it can create the AP VLAN
for it. With this patch, the mlme code emits a 4-addr nullfunc frame
immediately after assoc. On the AP side it also drops 4-addr nullfunc
frames to the cooked monitor mode interface, if the interface hasn't
been fully set up to receive 4-addr data frames yet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This enhances the way we parse country IEs to minimize
the number of regulatory rules that we create. It also fixes
our current implementation which treated country IE triplets
with only one channel as one independed regulatory rule even
though adjecent rules were also being provided.
Without this patch APs which send country IE information with
a channel triplet for each individual channel will force cfg80211
to deny HT40 operation as a regulatory rule would have been created
independently for each channel and as such configured only for
20 MHz operation.
Although 802.11n APs which send country IEs triplets in this fassion
are likely rare Benoit reports this against the Ubiquity NanoStation M5,
with Country "FR" and HT40 enabled.
Since we now have a helper which parses the triplets in intermediate
steps we now take care extra care to process padding.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The max power from each country IE triplet was being ignored.
This fix isn't critical as CRDA was always being used for the lower
limit, but we should process it in case the AP still wants to
decrease power output even more for whatever reason.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Kalle and Lennert reported problems with the new work
code, and at least Kalle's problem I was able to trace
to a missing jiffies initialisation.
I also ran into a problem where occasionally I couldn't
connect, which seems fixed with kicking the work items
after scanning.
Finally, also add some sanity checking code to verify
that we're not adding work items while an interface is
down -- that case could lead to something similar to
what Lennert was seeing.
There still seems to be a race condition that we're
trying to figure out separately.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Store information elements from Beacon and Probe Response frames in
separate buffers to allow both sets to be made available through
nl80211. This allows user space applications to get access to IEs from
Beacon frames even if we have received Probe Response frames from the
BSS. Previously, the IEs from Probe Response frames would have
overridden the IEs from Beacon frames.
This feature is of somewhat limited use since most protocols include
the same (or extended) information in Probe Response frames. However,
there are couple of exceptions where the IEs from Beacon frames could
be of some use: TIM IE is only included in Beacon frames (and it would
be needed to figure out the DTIM period used in the BSS) and at least
some implementations of Wireless Provisioning Services seem to include
the full IE only in Beacon frames).
The new BSS attribute for scan results is added to allow both the IE
sets to be delivered. This is done in a way that maintains the
previously used behavior for applications that are not aware of the
new NL80211_BSS_BEACON_IES attribute.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As mac80211 now has a separate function for creating Probe Request templates,
better to use it when sending direct Probe Requests to an AP. Only the
bssid needs to be updated in the template before sending it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Certain type of hardware, for example wl1251 and wl1271, need a template
for the Probe Request. Create a function ieee80211_probereq_get() which
creates the template and drivers send it to hardware.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To avoid duplicate code, use ieee80211_[pspoll|nullfunc]_get() to get
templates for PS Poll and Nullfunc frames in mlme.c.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some hardware, for example wl1251 and wl1271, handle the transmission
of power save related frames in hardware, but the driver is responsible
for creating the templates. It's better to create the templates in mac80211,
that way all drivers can benefit from this.
Add two new functions, ieee80211_pspoll_get() and ieee80211_nullfunc_get()
which drivers need to call to get the frame. Drivers are also responsible
for updating the templates after each association.
Also new struct ieee80211_hdr_3addr is added to ieee80211.h to make it
easy to calculate length of the Nullfunc frame.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a new NL80211_CMD_SET_TX_BITRATE_MASK command and related
attributes to provide support for setting TX rate mask for rate
control. This uses the existing cfg80211 set_bitrate_mask operation
that was previously used only with WEXT compat code (SIOCSIWRATE). The
nl80211 command allows more generic configuration of allowed rates as
a mask instead of fixed/max rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.
Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.
The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the basic rate set is configured to not include the lowest rate
(e.g., basic rate set = 6, 12, 24 Mbps in IEEE 802.11g mode), the AP
should not send out broadcast frames at 1 Mbps. This type of
configuration can be used to optimize channel usage in cases where
there is no need for backwards compatibility with IEEE 802.11b-only
devices.
In AP mode, mac80211 was unconditionally using the lowest rate for
Beacon frames and similarly, with all rate control algorithms that use
rate_control_send_low(), the lowest rate ended up being used for all
broadcast frames (and all unicast frames that are sent before
association). Change this to take into account the basic rate
configuration in AP mode, i.e., use the lowest rate in the basic rate
set instead of the lowest supported rate when selecting the rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make addba_resp_timer aware the HT_AGG_STATE_REQ_STOP_BA_MSK mask
so that when ___ieee80211_stop_tx_ba_session() is issued the timer
will quit. Otherwise when suspend happens before the timer expired,
the timer handler will be called immediately after resume and
messes up driver status.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mac80211 callback to driver set_coverage_class() sets slot time and ACK
timeout for given IEEE 802.11 coverage class. The callback is optional,
but it's essential for long distance links.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).
The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
net/mac80211/scan.c
net/mac80211/wme.c
|
|
This reverts commit 53623f1a09c7a7d23b74f0f7d93dba0ebde1006b.
This was inadvertantly missed in "mac80211: fix skb buffering issue",
and is required with that patch to restore proper queue operation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"mac80211: fix skb buffering issue" is based on what will become 2.6.34,
so it includes an incompatible usage of sta_info_get. This patch will
need to be effectively reverted when merging for 2.6.34.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Bad macro definition in "cfg80211: add a regulatory debug print"...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
net/mac80211/iface.c
|
|
The start_seq_num is taken from the station's tid_seq[tid].
This is fine, except tid_seq sequence counter is shifted
by 4 bits to accommodate for frame fragmentation.
Both (iwlagn & ath9k) were unaffected by this minor glitch,
because they don't read the *ssn for the AMPDU_TX_START action.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of sprinkling code with ifdef's define REG_DBG_PRINT() instead.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Setting the mac address from user space was buggy. For example, when
executing this command:
ip link set wlan0 address 00:1f:df:88:cd:55
mac80211 used the address 01:00:00:1f:df:88 instead. It was shifted two
bytes.
The reason was that the addr (type of void *) provided to
ieee80211_change_mac() is actually of type struct sockaddr, not just the
mac address array. Also the call to eth_mac_addr() expects the address to
be struct sockaddr.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On a 32 bit system (in this case an omap 3430 system) gcc warned about
pointer conversion:
net/mac80211/work.c: In function 'ieee80211_remain_on_channel_timeout':
net/mac80211/work.c:534: warning: cast from pointer to integer of different size
net/mac80211/work.c: In function 'ieee80211_remain_done':
net/mac80211/work.c:1030: warning: cast from pointer to integer of different size
net/mac80211/work.c: In function 'ieee80211_wk_remain_on_channel':
net/mac80211/work.c:1056: warning: cast from pointer to integer of different size
net/mac80211/work.c: In function 'ieee80211_wk_cancel_remain_on_channel':
net/mac80211/work.c:1072: warning: cast from pointer to integer of different size
Fix it by casting the pointers to unsigned long instead. This makes the
compiler happy again.
Compile-tested only.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove the forgotten linux/wireless.h inclusion from mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.
This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.
The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes a syntax error when setting up the user regulatory
hint. This change yields the same exact binary object though
so it ends up just being a syntax typo fix, fortunately.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
'Typo: it's "Hardware", not "Harware". Hmm, sometimes it's hairware :-)"'
-- Holger Schurig
Reported-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
drivers/net/wireless/libertas/scan.c
|
|
To make it easier to notice cases of calling sleeping ops in atomic context,
annotate driver-ops.h with appropiate might_sleep() calls. At the same time,
also document in mac80211.h the op functions with missing contexts.
mac80211 doesn't seem to use get_tx_stats anywhere currently. Just to be on
the safe side, I documented it to be atomic, but hopefully the op can be
removed in the future.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's no need to be requeueing the work struct
since we check for the scan after removing items
due to possible timeouts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This changes mac80211 to allow being off-channel for
any type of work, not just the 'remain-on-channel'
work. This also helps fast transition to a BSS on a
different channel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This implements the new remain-on-channel cfg80211
command in mac80211, extending the work interface.
Also change the work purge code to be able to clean
up events properly (pretending they timed out.)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.
The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The off-channel operations for going into power save mode (station
mode) or stop beaconing (AP/IBSS) are not limited to scanning. Move
these into a separate file and allow them to be used for other
purposes, too.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
cfg80211 offers private data for each BSS struct,
which mac80211 uses. However, mac80211 uses internal
and external (cfg80211) BSS pointers interchangeably
and has a hack to put the cfg80211 bss struct into
the private struct.
Remove this hack, properly converting between the
pointers wherever necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, we insert all user-specified IEs before the HT
IE for association, and after the HT IE for probe requests.
For association, that's correct only if the user-specified
IEs are RSN only, incorrect in all other cases including
WPA. Change this to split apart the user-specified IEs in
two places for association: before the HT IE (e.g. RSN),
after the HT IE (generally empty right now I think?) and
after WMM (all other vendor-specific IEs). For probes,
split the IEs in different places to be correct according
to the spec.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
