| Age | Commit message (Collapse) | Author |
|---|
|
Modules: HDA Codec driver
The following patch adds a 'test' ALC260 model specification to the
patch_realtek.c driver if CONFIG_SND_DEBUG is set. This is similar to the
'test' ALC880 model in that it sets up mixer controls for almost everything
to make it easier for people to test their laptop/soundcard when working out
what pin widgets are connected to which real-world devices.
This patch assumes my previous patch (adding the second PCM to the ALC260)
has previously been applied since it uses infrastructure added by that
patch.
In developing this patch it was found that not all retasking pins accept all
the modes - in particular, some ignore the VREFxx variants. The pin mode
control has therefore been tweaked to prevent this becoming a problem in
mixer applications.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
The following patch changes the initverbs associated with the output sum
widgets 0x08, 0x09 and 0x0a used with the fujitsu model in patch_realtek.c.
It is against alsa 1.0.11rc3.
Currently these widgets have their output muted, but a close reading of the
datasheet suggests that they don't actually have an output mute. They have
an *input* mute for each of their two inputs and a single output gain. This
patch therefore activates the input mutes and zeros the output gain. It has
not yet been tested but the above interpretation of the ALC260 datasheet
seems correct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
The following patch against alsa 1.0.11rc3 creates a PCM device (pcm1c) for
the second ADC present on the ALC260 codec used by the hda driver. It also
defines a new mixer control allowing the mode of retasking pins to be set;
this means a user can (for example) designate the headphone jack to be a
second input. With this patch in place it is possible to do 4 channel
recording on laptops equipped with an ALC260 codec assuming both a stereo
line-in jack is provided in addition to a headphone jack.
Mixer controls are provided to allow the headphone jack to be switched as
an input. In addition, an (input only) mode control is configured for
the line-in jack to allow a bias voltage to be requested (VREF80 or VREF50)
so headsets based on condensor microphones have a chance of working.
This patch has been tested on a Fujitsu S7020 laptop and as such these
features are currently only configured for the 'fujitsu' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Documentation,HDA Intel driver
Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fixed typos in alc882 model table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
This little patch add the model for the motherboard K8N51 from Gigabyte
to the known models of ALC boards.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
* Fix init sequence so manually retaskable jacks don't get added to
the line_out list.
* Update intel mobo config defaults to specify surround outputs
as line outs rather than speakers.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fixed the wrong widget id for line-2 selector in the init verb
of ALC260.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fix max_channels computation for STAC92xx codecs in the case only
HP pin without line-out pins is detected in the default pin config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Adds support for the SigmaTel STAC927x HDA codec family.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Add SigmaTel HDA support for the Intel D975XBK motherboard.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
This adds support for Agere's variant of Si3054/5 based HDA modem.
Signed-off-by: Sasha Khapyorsky <sashak@alsa-project.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Added the missing 'Capture Switch' control for Sigmatel STAC92xx codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Added an ALC260 model entry (basic) for Sony VAIO.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
This patch adds the Intel ICH8 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Added the model entry for Shuttle ST20G5.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Add the model entry (ALC880 6stack) for ASUS P5GD1-HVM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
- Common labels for input pins
- Fix and clean up of Realtek codec parsers
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
- Fix Oops with auto-probing of ALC260 with digital I/O
- Fix a typo
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
- Fix ALC882 BIOS auto-probe
- Fix ALC262 basic model
- Add assert for debugging Oops
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
This patch adds the support of ALC262,ALC883,ALC885,ALC861 to driver
More models and improvements for ALC880, ALC260 and ALC882 codecs, too.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
- Explictly set pin control as input for all input pins
- Fix bug in 922x mixer (no mute on adc0vol)
- Remove broken ch_mode control
- Add support for jack retasking mixer controls to use rear line and
mic as surround outputs
- Add board tables to support autodetect and pin config defaults for
systems with broken bioses
- Add support for several Intel mobos
- Add support for DFI mobo with reference boards attached
(gets rid of compile time switch to use reference boards)
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
The probe_mask module parameter comment notes that the intended
default is -1. Fix it to be so, otherwise all codecs are skipped
and init fails.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fixed the swapped surround/CLFE on 3stack mode of AD1988.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fix/enhance AD1988 support code.
- Fix for h/w bug of AD1988A rev 2
- The BIOS auto-configuration is added and used as fallback
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fix the channel mode helper (for put callback).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
- Use the position buffer for obtaining the current DMA position
as default. This seems more stable than others.
- Add probe_mask module option (mainly for test boards with multiple
codecs).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
This patch is to fix the problem of calculating the nid incorrectly
when auto-probe for ALC880. The problem to be fixed often behaves
with such words when using dmesg, 'num_steps = 0 for NID=0x8' when
auto-probe for ALC880.
The patch contains:
- alsa-kernel/pci/hda/patch_realtek.c: replace 'alc880_dac_to_idx'
with 'alc880_idx_to_dac' in function 'alc880_auto_fill_dac_nids()'
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: RawMidi Midlevel,HDA generic driver
This patch contains the following possible cleanups:
- pci/hda/hda_proc.c should #include 'hda_local.h' for including the
prototype of it's global function snd_hda_codec_proc_new()
- core/rawmidi.c: make the needlessly global and EXPORT_SYMBOL'ed
function snd_rawmidi_info() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fix AD1988 support. As default, 6stack model is used.
Still no auto-BIOS setup is implemented.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA generic driver
Allocate connection lists dynamically in generic parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
- Fix connection list parsing (with ranged flag).
- Increase the max number of connections
- Introduce widget capabilities cache
- Power up/down widgets at init, suspend and resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Fix PM support on HDA-Intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Add AD1988 codec support to hda-codec driver.
Still experimental, and no BIOS configuration parser is implemented yet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Remove xxx_t typedefs from the HDA-Intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Remove xxx_t typedefs from the HD-Audio codec support codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Fix the auto-assignment of speaker pin. Handle it independently from
line-out pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Fix a typo in hda_codec.h.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Prepare unsol workqueue only when a codec really supports.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
Add common channel-mode helper functions for all codec patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
The patch fixes the problem of mute onboard HDA sound output,
buildin V.92 modem idendification and functionality.
Signed-off-by: Daniel Mueller <daniel.mueller@siemens.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Rate-limit the azx_get_response timeout message. A continuous 2 per second
is too much.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Allocate amp hash array dynamically instead of static array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Modules: HDA Codec driver,HDA generic driver
- Make bound controls global to all patches
- Clean up analog patches (for the upcoming extension to AD1988)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA generic driver
Show the power state of each widget in proc file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the type of enable module option to bool.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Get subsytem ID from AFG/MFG if not obtained from the root node.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Intel8x0-modem driver,VIA82xx-modem driver,HDA Codec driver
Signed-off-by: Sasha Khapyorsky <sashakh@alsa-project.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
