| Age | Commit message (Collapse) | Author |
|---|
|
On the HT-Omega Claro (halo) sound cards, the headphone amplifier must
be enabled explicitly by setting a GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Model drivers assume that model_data is zeroed, so we better use
kzalloc() (like we did before when it was allocated together with the
card structure).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for the Asus Xonar Essence STX sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use -60 dB as the minimum value of the master volume mixer control.
While the DACs would support ranges down to about -120 dB, such
attenuations are not useful in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The HT-Omega Claro halo's ADC is an AK5385 instead of a WM8785, so we
should handle the ADC parameters as we do with the X-Meridian.
Using the code for the wrong ADC does not seem to have any audible
effects, and the Windows driver does it, but it is nonetheless a good
idea to run the AK5385 with an oversampling ratio that is not outside
the documented limits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the EEPROM was partially overwritten (which seems to happen before the OS is
booted), restore its entire contents by deducing it from the remaining
information.
This does not have any effect on the Linux driver, which works even with
incomplete information in the EEPROM, but it makes other drivers work again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Under as yet unknown circumstances, the first word of the sound card's
EEPROM gets overwritten. When this has happened, we cannot rely on the
subsystem IDs that the kernel reads from the PCI configuration
registers. Instead, we read the IDs directly from the EEPROM and do the
ID matching manually.
Because the model-specific driver cannot determine the model before
calling oxygen_pci_probe(), that function now gets a get_model()
callback as parameter. The customizing of the model structure, which
was formerly done by the probe() callback, also has moved into
get_model().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When allocating resources, use a fixed name instead of reading it from
the model structure. This allows us to allocate the resources before
the actual model is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Allocate the model-specific data dynamically instead of including it in
the memory block of the card structure. This will allow us to determine
the actual model after the card creation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the owner field out of the oxygen_model structure and make it
a parameter of oxygen_pci_probe(), because the actual owner module does
not depend on the card model. Furthermore, moving it out of the model
structure allows us to create the card structure before the actual model
is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
This reverts commit 7e86c0e6850504ec9516b953f316a47277825e33 ("do not
overwrite EEPROM on Xonar D2/D2X") because it did not actually help with
the problem.
More user reports show that the overwriting of the EEPROM is not
triggered by using this driver but by installing Linux, and that the
installation of any other operating system (even one without any CMI8788
driver) has the same effect. In other words, the presence of this
driver does not have any effect on the occurrence of the error. (So
far, the available evidence seems to point to a BIOS bug.)
Furthermore, it turns out that the EEPROM chip is protected against
stray write commands by the command format and by requiring a separate
write-enable command, so the error scenario in the previous commit (that
SPI writes can be misinterpreted as an EEPROM write command) is not even
theoretically possible.
The mixer control that was removed as a consequence of the previous
commit can only be partially emulated in userspace, which also means it
cannot be seen be the in-kernel OSS API emulation, so it is better to
revert that change.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a missing newline.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This hardware has a better chance of working correctly if we don't
forget to enable it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On the Asus Xonar D2 and D2X models, the SPI chip select signal for the
fourth DAC shares its pin with the serial clock for the EEPROM that
contains the PCI subdevice ID values. It appears that when DAC
registers are written and some other unknown conditions occur (probably
noise on the EEPROM's chip select line), the EEPROM gets overwritten
with garbage, which makes it impossible to properly detect the card
later.
Therefore, we better avoid DAC register writes and make sure that the
driver works with the DAC's registers' default values. Consequently,
the sample format is now I2S instead of left-justified (no user-visible
change), and the DAC's volume/mute registers cannot be used anymore
(volume changes are now done by the software volume plugin).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Convert from snd_card_new() to the new snd_card_create() function
in sound/pci/*.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for the HT-Omega Claro halo (XT).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After sending a reset command to the UART, wait some time for the ACK to
be generated (and to be read and dropped by the interrupt handler)
before sending the next command.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add support for the Asus Xonar HDAV1.3 and the Xonar HDAV1.3 Deluxe.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Rename the first PCM device from "Analog" to "Multichannel" because it
can be used for HDMI output on the Xonar HDAV.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Rename the callback function that switches between line and mic inputs
on the Xonar D1 because it is also usable on other models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Do not use a hardcoded number when iterating over the PCM1796 DACs to
allow for cards with a different number of analog output channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add support for PCM1796 chips that are connected with an I2C bus instead
of SPI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Introduce some trivial functions to better document the relationships of
the various model callbacks.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add functions to allow model drivers to communicate with external chips
by doing I/O with the not-used-for-MIDI UART.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
To enable the MIDI port, model drivers must now set flags in
device_config, not only in misc_flags. This allows model drivers to
enable the UART without creating an ALSA MIDI device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Rename the pcm_dev_cfg field to device_config because there will be
additional flags that do not describe PCM devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Factor out the common code of the mixer callbacks that handle controls
that just switch a single GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
The Xonar D2X and DX are very similar to the D2 and D1, respectively, so
we can handle the differences dynamically instead of using a separate
model structure for each one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Handle the differences between the X-Meridian and the other models in
the probe callback instead of using a second model structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Introduce symbols that indicate the two models handled by the snd-oxygen
driver, instead of using a magic number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add a probe callback to the model structure so that model-specific
drivers can refine their model detection before the card is initialized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Put a copy of the model structure into the chip structure so that model-
specific drivers can modify it depending on a particular device
instance.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
When setting the SPDIF channel status sample rate field, use the
recently defined symbols instead of magic numbers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time. The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value. In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.
To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Xonar DX does not have CD Capture controls, so we have to check that
a control actually exists before muting it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a constraint for the period time so that there are less than ten
seconds between interrupts so that ALSA does not assume that the device
is dead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Introduce symbols for the buffer/period size constraints so that their
limits and relationships become clearer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Add suspend/resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Move the setting of the output enable GPIO bit to a separate function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Create separate functions for the code that initializes the hardware, as
opposed to initializing internal driver state, so that they can be
reused for resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
When initializing the DAC volume registers, we can just use the generic
volume update functions instead of setting the registers manually.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Save the written values of all CMI8788 and AC97 registers and of some of
the DAC/ADC registers so that it is possible to restore the register
state later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Remove another magic number - add a symbol for the size of the PCI I/O
range.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Adjust the MODULE_LICENSE strings to properly reflect the actual license.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
Check that model->control_filter is set before trying to call it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a pointer for DAC volume TLV data to the model structure so that the
model driver do not need to manually assign it in their control filter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initialize the playback volume controls as being muted and having
minimal volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
