| Age | Commit message (Collapse) | Author |
|---|
|
CS4281 driver
Reset the FPDN bit of the EPPMC register if needed.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
EMU10K1/EMU10K2 driver
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
e.g. When HD Capture source is set to SPDIF,
setting HD Capture channel to 0 captures from CDROM digital input.
setting HD Capture channel to 1 captures from SPDIF in.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
The capture rate does in fact vary, but it only captures anything if
the HD Capture source is set to I2S or AC97. I have not tested if the sound
is actually captured from an physical input of some type or not.
TODO: Get SPDIF capture working.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
RME HDSP driver
ppc firmware upload fix
Signed-off-by: Thomas Charbonnel <thomas@undata.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
AC97 Codec
Add the 'Mic Front Input Switch' control to the mixer for ALC850.
Enabling this input is required for using the front panel microphone
connector with ASUS A8V motherboard.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
AC97 Codec
ac97_enum mixer elements (e.g., 'Capture Source') did not work because
of wrong bitmask calculation in snd_ac97_get_enum_double() and
snd_ac97_put_enum_double().
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1072
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
VIA82xx driver
Report by Ronny V. Vindenes <s864@ii.uib.no>
Add dxs_support=5 for MSI K8T Neo-FIS2R.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA Codec driver
Fix and cleanup of CM9880 automatic PIN configuration.
snd_hda_codec_setup_stream() doesn't do anything when NID is 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA generic driver
Show the jack type of each PIN default configuration entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA generic driver
Fix a typo in comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
When building with gcc -W sound/pci/emu10k1/emupcm.c produces this little
warning in 2.6.12-rc2-mm3 :
sound/pci/emu10k1/emupcm.c:265: warning: 'inline' is not at beginning of
declaration
No big deal, but trivial to fix.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
VIA82xx driver
Added dxs_support=5 entry for Insight P4-ITX.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA Codec driver
Misc clean up: move the definitions of constants for pinctl to a single place.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA Codec driver
Removed the dead (duplicated) code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA Codec driver
Added the support of AD1981HD and AD1983 codecs.
Including the fix for AD1986A.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA generic driver,HDA Codec driver
Add initial SigmaTel codec support for 9200 and 922x. Note that
this hda patch relies on the configuration default registers to
be set correctly (normally by BIOS/firmware) in order for it to
set up pin widgets properly. There's a test switch in the patch
so it will work with the SigmaTel reference boards that are usually
plugged into a system that doesn't set the configuration default
registers. It supports 2 channel analog out and line/mic in. I
plan to add >2 channel support and spdif support shortly.
Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA Codec driver,HDA generic driver
Fix some vref defines so they are valid for the different bits in
the pin cap and pin control registers. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec
The handling of shared surround/clfe output jacks with line/mic-in
on some AC97 codecs is improved.
Instead of 'Line-In As Surround' or 'Mic As Center/LFE' switch, two
new enum controls are introduced: 'Channel Mode' and 'Surround Jack Mode'.
The formar changes the current output mode among 2, 4 and 6-channels.
The latter controls whether the jacks are shared or independent.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
PCM Midlevel,CA0106 driver,EMU10K1/EMU10K2 driver
Fix by Guillaume Chazarain <guichaz@yahoo.fr>:
Some tunables in /proc have a write() function, but as their
permission does not reflect it, it can be confusing to the user.
So here is a patch that corrects the mode of those files. Note that I
have only tested the 'xrun_debug' entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
Fix compile warnings regarding the unused variables/functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Documentation,ALS4000 driver,ATIIXP driver,ATIIXP-modem driver
AZT3328 driver,BT87x driver,CMIPCI driver,CS4281 driver
ENS1370/1+ driver,ES1938 driver,ES1968 driver,FM801 driver
Intel8x0 driver,Intel8x0-modem driver,Maestro3 driver,RME32 driver
RME96 driver,SonicVibes driver,VIA82xx driver,VIA82xx-modem driver
ALI5451 driver,au88x0 driver,CA0106 driver,CS46xx driver
EMU10K1/EMU10K2 driver,HDA Intel driver,ICE1712 driver,ICE1724 driver
KORG1212 driver,MIXART driver,NM256 driver,RME HDSP driver
RME9652 driver,Trident driver,Digigram VX222 driver,YMFPCI driver
Replace the obsolete pci_module_init() with pci_register_driver().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
VIA82xx driver
Fix SPDIF rate setting with dxs_support=4. It should be 48k fixed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Documentation,VIA82xx driver
Add support for full sample rate conversion capabilities of DXS
channels present in VIA VT8233/5/7 controllers:
- any sample rate in the 8000 ... 48000 Hz range is supported even if
the AC'97 codec supports only 48000 Hz output;
- different DXS channels can use different sample rates at the same
time (the controller performs required sample rate conversion and
mixing in hardware).
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
FM801 driver
The Gallant Odyssey Sound 4 card is based on the ForteMedia FM801
chip, but has a different PCI ID.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
YMFPCI driver
This patch removes some dead code found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ICE1712 driver
Provides preliminary support for the Terratec Phase 28 card.
Not extensively tested and probably buggy, but it seems to work.
Signed-off-by: Simone Zinanni <simone@develer.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
when using the p16v HD device.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
Although we can set 44100 as the output rate, the SPDIF can do it, but the Analog output cannot.
The SPDIF has the bug, whereby the Left channel arrives one sample late, so although we don't do any resampling,
it is not good for AC3 non-audio output.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
HDA Codec driver
Patch by C.L. Tien <cltien@cmedia.com.tw>:
The patch makes cm9880 to choose multi-channel jacks automatically.
1. I found the current code has basic_init, which already includes
necessary controls for 6-stack initialization, so I don't need
another model.
2. I add a new model 'auto' to let the driver find a. if there are
option real panel/front panel, b. the jacks to be used for multichannel.
Because the jack color are based on MS's channel sequence, so the 'auto'
model will pick the same jacks for multichannel MS uses. I did this to
hope to minimize users questions. These code can also be applied to other
codecs but I don't have any to test.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec
Separated ac97 registers reset for audio and modem (or both) as recommended
in AC97 spec.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec
This (especially 12000 -> 8000 sample rate replace) fix popular
'MC97 converters.. not ready' error with modem codecs initializations.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Intel8x0-modem driver
With some intel based ac97 modems codec access semaphore is not cleared
after 0x54 AC97 register (GPIO_STATUS) reads. This may causes problems
with newly applied modem mixer (Off-hook switch) and in other cases.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec
- Added CM9780 patch
- Fix the SPDIF support on CM9761/CM9780
- Allow the generic enum callback to pass any number (not power of 2)
as the value mask
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec
Removed unused variables (the old control definitions).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
Check ther revision to detect non-listed audigy 2 boards.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
This add identification of Audigy 1 model SB0090 and fixes
problems with ac97 codec (mic not working).
Signed-off-by: Peter Zubaj <pzad@pobox.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
Fixed the default id string in case identical multiple cards exist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
Use expliciitly the old default id strings for backward compatibility.
This will make 'alsactl restore' working again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
This patch converts the emu10k1 driver to use the card capabilities
structure for some more things.
Not extensively tested but seems to work.
Signed-off-by: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec
Fixed the detection of bit resolution of ac97 mixer controls.
This will fix the problem with TI ac97 codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EMU10K1/EMU10K2 driver
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
EMU10K1/EMU10K2 driver
One can select which capture source, but one cannot yet set volumes.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
|
|
HDA Codec driver
The patch_cm9880.c can't play side/C/B channels from front panel jacks.
I fixed it by adding select pin.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
CA0106 driver
Skip building ac97 SPDIF controls via AC97_SCAP_NO_SPDIF.
Clean up the code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA generic driver
During debugging for cm9880 multi-channel playback, I added the * after
the currently selected widget, mixer widget doesn't need this but other
3 widget types need it.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Trying software suspend on my workstation makes it crash on resume. The
problem is that via82xx marks the chip_init function as _devinit, but calls
it on resume as well.
Cc: <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
