aboutsummaryrefslogtreecommitdiff
path: root/sound/pci
AgeCommit message (Collapse)Author
2007-10-16[ALSA] cmipci: allow 96 kHz playback on non-multichannel rearClemens Ladisch
Move the code that enables 96 kHz out of the if() that checks for availability of both DMA channels so that it is enabled even when another stream is playing on the front channels. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: initialize 0x90 registersClemens Ladisch
Initialize the registers at 0x90 and 0x91 with some undocumented values. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: reset the chip when initializingClemens Ladisch
When the chip is initialized, reset it. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: show more registers in proc fileClemens Ladisch
Show a dump of all registers in the 0x00-0x27 and 0x90-0x93 ranges in the 'cmipci' proc file. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: update register definitionsClemens Ladisch
Update comments for many register symbols, add some new register symbols, and rename a few ones. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: fix version 37 detectionClemens Ladisch
Use the proper value for the bit that identifies chip version 37. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] bt87x: fix detection of generic boardsClemens Ladisch
Add an 'unknown' board type so that it is possible to differentiate between unknown and generic boards. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] echoaudio - Remove superfluous volatile prefixTakashi Iwai
Remove superfluous volatile prefix in the communication struct definition. This eventually fixes the compile warnings with the recent gcc, too. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-intel - Improve HD-audio codec probing robustnessDanny Tholen
When modem is disabled in the BIOS, detection of the number of codecs always fails after booting if STATESTS is not cleared first. This patch fixes this problem and also adds an error check in a place where a read error would lead to a very large number of pointless loops. Signed-off-by: Danny Tholen <obiwan@mailmij.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] pcxhr - Fix trigger start with non-linked streamsTakashi Iwai
The non-linked streams couldn't be started properly due to missing setting of stream->status. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] au88x0_synth.c bugfixAdrian Bunk
This patch fixes the code in vortex_wt_SetFrequency() to what seems to have been intended. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda: BIOS changing subsystem idMatthew Ranostay
Some laptop BIOS change the subsystem id for STAC9205 cards if the microphone isn't toggled on/off in the settings. Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] snd-bt87x: Power down audio ADC when not in useTrent Piepho
Sets a bit to power down the Bt87x's internal audio ADC when the ALSA device isn't open, or when it is in 'digital mode' using an external ADC. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: add msbits constraint for 24-bit formatClemens Ladisch
Add a msbits constraint to the SPDIF output device to indicate that S32_LE samples use only 24 bits for data. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add support for Toshiba A305Takashi Iwai
Added the proper model=toshiba for Toshiba A305 with ALC268 codec. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add missing Mic Boost for some ALC882 modelsTakashi Iwai
Mic Boost mixer volume was missing in some ALC882 models. Added now. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] snd-bt87x: Improve support for different board typesTrent Piepho
Different cards have different audio configurations, but the driver didn't support this. The only setting it had was the digital rate. This patch adds a board configuration list. Currently, configurable items are the digital rate and the digital data format (for cards with an external ADC), a flag for the absence of an external ADC, and a flag for no connection to the Bt87x internal ADC. This allows cards that don't use the internal ADC to omit the ALSA 'Bt87x analog' device and related controls. Cards without an external ADC can omit the 'Bt87x digital' device. In order to support the CS5331A ADC used on the Osprey 440 and 2x0 cards, the digital format needs to be different than the default. Support could be added for defining: The connections or lack of them to the Bt87x's internal ADC mux Multiple sample rates for an external ADC (e.g. Osprey) Control of an external mux for an external ADC (e.g. Osprey) The card definitions for cards other than the Ospreys are kept equivalent to their old values. This is likely inaccurate for most cards, as it is doubtful that both an external and the internal ADC would be used. Lacking information on those cards, the behavior is left unchanged. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add quirk entry for Casper CPR2000Takashi Iwai
Added the quirk entry for Casper CPR2000 (model=acer) with ALC268 codec (ALSA bug#3343). Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add missing model names for ALC882 codecsTakashi Iwai
Added the missing model option strings for ALC882 codecs. Also added the corresponding description in ALSA-Configuration.txt. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add support for ASUS A7MTakashi Iwai
Added the support for ASUS A7M with ALC882 codec. It's slightly different from ASUS A7J. The patch taken from ALSA bug#3000 https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3000 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add laptop-automute model for AD1986ATakashi Iwai
Added a new model laptop-automute for AD1986A, which has the HP jack detection and auto-muting of the speaker. Currently, it's used for Lenovo N100. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Fix wrong pin config order in STAC92xx dell modelsTakashi Iwai
The last patch to change/add Dell models have wrong pin config orders. This patch fixes the pin positions. Taken from ALSA bug#3319, https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3319 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add support for Acer Aspire 9303Takashi Iwai
Add the entry for Acer Aspire 9303 (model=acer-aspire) with ALC883 codec. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cs5535audio: drop unused bus master stuffAndres Salomon
We really only care about the first two bus masters (playback and capture). There's no need to have unused BM code lying around, so let's get rid of it. If for some reason we trigger an IRQ for some BM that we're not using.. well, that warrants spitting out an error message (imo). Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cs5535audio: fix ACC_BM[x]_CMD register handlingAndres Salomon
According to 6.3.2.7 of the cs5535/cs5536 data sheets, the ACC_BM[x]_CMD registers are only 8 bits wide. This driver treats them as 32 bits wide, and also has bits in the wrong place. Simple fix to the definitions. Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cs5535audio: update PCI device handling in suspend/resumeAndres Salomon
Save the PCI state before disabling the device, and add some error checking. Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cs5535audio: fix PRD register save/restore power management raceAndres Salomon
In the suspend path, we currently save the PRD registers and then disable DMA. This is racy; the sound hardware might update the PRD register as it finishes processing some DMA pages between when we've saved the PRD registers and when DMA actually gets disabled. Furthermore, we actively check whether or not DMA is enabled before saving PRD registers; there's no reason to do that, as the PRD registers should not update when we twiddle the ACC_BM[x]_CMD register(s). Worst case, we save the PRD registers twice; even powering down the ACC shouldn't mess with the PRD registers (according to the 5536 data sheet, section 5.3.7.4, power-down procedure). This patch reworks all that to first disable DMA, and then save PRD registers. Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cs5535audio: correctly set dma->substreamAndres Salomon
We're never actually setting dma->substream to the current substream; that means the dma->substream checks that we do in the suspend/resume path are never satisfied, and the PRD registers are never correctly managed. This changes it so that we set the substream when constructing the specific bus master DMA, and unsetting it when we tear down the BM's DMA. Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Fix support for sigmatel codecs that have 2 or more ADCsMaxim Levitsky
1) Create seperate mixer controls for each ADC 2) Make number of substreams of capture PCM device be equal to number of ADCs Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - make volume knob, the master volume for sigmatel codecsMaxim Levitsky
VolumeKnob is present on most sigmatel codecs, it allows to decrease volume of all DACs at once, it is a kind of post-procesing volume. Note that all output amps of sigmatel only decrease volume, and all input amps only increase volume. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - add support for analog loopback to STAC9204/9205/922x/927xMaxim Levitsky
The analog loopback routes the sound just before it enters ADC0 to output of DAC0. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - add support for swapping center/LFE channels to STAC codecsMaxim Levitsky
Center/LFE channels are located on same jack, so it can be usefull to swap them. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-intel - Fix resume logic, when dynamic power managment is onMaxim Levitsky
Comment in hda_intel.c states that 'the explicit resume is needed only when POWER_SAVE isn't set', but this is not true. There is no code that will automaticly power up the codec on resume, but only code that powers it up when user accesses it. So if user leaves a sound playing, codec will not be powered To fix that I check if there are any codecs that should be powered codec->power_count, and if so I power them up together with main controller. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-intel - fix a race in dynamic power managmentMaxim Levitsky
codec->power_transition is supposed to be true while codec is going to be shut off if in the mean time somebody calls snd_hda_power_up, hda_power_work will not shut down the codec, but nether will clear codec->power_transition, thus it stays on forever. Fix this. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: show real chip name in card nameClemens Ladisch
The '-MCx' suffix that is expected by alsa-lib is only needed in the card driver string, so we can show the actual chip name in the shortname. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: check that the legacy MIDI port worksClemens Ladisch
Check that the UART_EN bit actually enabled the MPU-401 port. Apparently, C-Media thinks that it is a good idea to be paranoid here. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: do not check for integrated FM/MIDI ports with chip version 37Clemens Ladisch
Integrated MPU-401/OPL3 ports are available with chip version 39 and later, so we do not test for the port with version 37. Now that the test is known to work, we can again enable the MIDI port by default. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: add 96 kHz supportClemens Ladisch
Add support for 88.2 kHz and 96 kHz analog and digital playback on CMI8768/CMI8770 chips. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: remove invalid channels constraintClemens Ladisch
Remove the constraint that sets the channel limit for the first playback device to that of the second one; the first device supports only stereo. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Avoid zero NID in line_out_pins[] of STAC codecsTakashi Iwai
The STAC codes adds line_out_pins[] for shared mic/line-inputs accordingly. But, the current code may give a hole with NID=0 in some setting, which results in an error at probe. This patch fixes the problem. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Fix wrong pin-setup at resume of STAC codecsTakashi Iwai
The resume procedure for STAC codecs overrides the cached values and results in the wrong (reset) PIN state. The patch gets rid of the overriding part and simplifies the resume. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - code cleanups in patch_sigmatel.cMaxim Levitsky
Clean up the mixer entries for Input Source using a macro. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Fix capture on ALC262 HP machineszhejiang
Fix the index for Front Mic capture source on ALC262 HP machines. Also, added the new capture source list for HP BPC DC7000 series to work properly. From: zhejiang <zhe.jiang@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hdsp - Add support for latset RME9632 revisionsRemy Bruno
added support for the latest revision of the 9632 (and hopefully a few following ones). The DSP matrix was not working because of wrong identification of the card in this part of the code. Signed-off-by: Remy Bruno <remy.bruno@trinnov.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hdspm - Fix autosync bugRemy Bruno
* better report of speed mode change failures * autosync_ref control bugfix (was reporting pref_sync_ref instead) (changed HDSPM_AES32_AUTOSYNC_FROM_NONE value to comply with array indexing in snd_hdspm_info_autosync_ref()) * added support for master modes up to 192kHz (clock source control value was restricted up to 96kHz) Signed-off-by: Remy Bruno <remy.bruno@trinnov.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] ac97 - Suppress the reset of audio-codec from modem-codec at resumeTakashi Iwai
On codec chips with both audio and modem functions (e.g. Conexant one), performing AC97_RESET resets the whole registers. When both audio and modem drivers are resumed at the same time, the modem one often is resumed after the audio, and it results in the reset of audio registers (ALSA bug#3333). This patch fixes such a problem. Since the modem codec basically doesn't need AC97_RESET, skip this initialization unless specified as audio. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] hda-codec - Add Mic Boost control with auto-configurationTakashi Iwai
Some codecs need Mic Boost mixer controls for obtaining a proper recording level, but the auto-configuration doesn't create them. This patch adds the creation of mic-boost controls on corresponding codecs. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] emu10k1: There's no need to cast vmalloc() return value in ↵Jesper Juhl
snd_emu10k1_create() vmalloc() returns void *. no need to cast. Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: show actual chip name in card longnameClemens Ladisch
Show the actual name of CMI8762/CMI8768/CMI8769/CMI8770 chips in the card longname instead of just using 'CMI8738' for all of them. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-10-16[ALSA] cmipci: remove has_dual_dacClemens Ladisch
Remove the has_dual_dac variable because it was always set. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 21:53:27 +0000