1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
|
#include <linux/linkage.h>
#include <linux/lguest.h>
#include <asm/lguest_hcall.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
#include <asm/processor-flags.h>
/*G:020 This is where we begin: head.S notes that the boot header's platform
* type field is "1" (lguest), so calls us here. The boot header is in %esi.
*
* WARNING: be very careful here! We're running at addresses equal to physical
* addesses (around 0), not above PAGE_OFFSET as most code expectes
* (eg. 0xC0000000). Jumps are relative, so they're OK, but we can't touch any
* data.
*
* The .section line puts this code in .init.text so it will be discarded after
* boot. */
.section .init.text, "ax", @progbits
ENTRY(lguest_entry)
/* Make initial hypercall now, so we can set up the pagetables. */
movl $LHCALL_LGUEST_INIT, %eax
movl $lguest_data - __PAGE_OFFSET, %edx
int $LGUEST_TRAP_ENTRY
/* The Host put the toplevel pagetable in lguest_data.pgdir. The movsl
* instruction uses %esi implicitly. */
movl lguest_data - __PAGE_OFFSET + LGUEST_DATA_pgdir, %esi
/* Copy first 32 entries of page directory to __PAGE_OFFSET entries.
* This means the first 128M of kernel memory will be mapped at
* PAGE_OFFSET where the kernel expects to run. This will get it far
* enough through boot to switch to its own pagetables. */
movl $32, %ecx
movl %esi, %edi
addl $((__PAGE_OFFSET >> 22) * 4), %edi
rep
movsl
/* Set up the initial stack so we can run C code. */
movl $(init_thread_union+THREAD_SIZE),%esp
/* Jumps are relative, and we're running __PAGE_OFFSET too low at the
* moment. */
jmp lguest_init+__PAGE_OFFSET
/*G:055 We create a macro which puts the assembler code between lgstart_ and
* lgend_ markers. These templates are put in the .text section: they can't be
* discarded after boot as we may need to patch modules, too. */
.text
#define LGUEST_PATCH(name, insns...) \
lgstart_##name: insns; lgend_##name:; \
.globl lgstart_##name; .globl lgend_##name
LGUEST_PATCH(cli, movl $0, lguest_data+LGUEST_DATA_irq_enabled)
LGUEST_PATCH(sti, movl $X86_EFLAGS_IF, lguest_data+LGUEST_DATA_irq_enabled)
LGUEST_PATCH(popf, movl %eax, lguest_data+LGUEST_DATA_irq_enabled)
LGUEST_PATCH(pushf, movl lguest_data+LGUEST_DATA_irq_enabled, %eax)
/*:*/
/* These demark the EIP range where host should never deliver interrupts. */
.global lguest_noirq_start
.global lguest_noirq_end
/*M:004 When the Host reflects a trap or injects an interrupt into the Guest,
* it sets the eflags interrupt bit on the stack based on
* lguest_data.irq_enabled, so the Guest iret logic does the right thing when
* restoring it. However, when the Host sets the Guest up for direct traps,
* such as system calls, the processor is the one to push eflags onto the
* stack, and the interrupt bit will be 1 (in reality, interrupts are always
* enabled in the Guest).
*
* This turns out to be harmless: the only trap which should happen under Linux
* with interrupts disabled is Page Fault (due to our lazy mapping of vmalloc
* regions), which has to be reflected through the Host anyway. If another
* trap *does* go off when interrupts are disabled, the Guest will panic, and
* we'll never get to this iret! :*/
/*G:045 There is one final paravirt_op that the Guest implements, and glancing
* at it you can see why I left it to last. It's *cool*! It's in *assembler*!
*
* The "iret" instruction is used to return from an interrupt or trap. The
* stack looks like this:
* old address
* old code segment & privilege level
* old processor flags ("eflags")
*
* The "iret" instruction pops those values off the stack and restores them all
* at once. The only problem is that eflags includes the Interrupt Flag which
* the Guest can't change: the CPU will simply ignore it when we do an "iret".
* So we have to copy eflags from the stack to lguest_data.irq_enabled before
* we do the "iret".
*
* There are two problems with this: firstly, we need to use a register to do
* the copy and secondly, the whole thing needs to be atomic. The first
* problem is easy to solve: push %eax on the stack so we can use it, and then
* restore it at the end just before the real "iret".
*
* The second is harder: copying eflags to lguest_data.irq_enabled will turn
* interrupts on before we're finished, so we could be interrupted before we
* return to userspace or wherever. Our solution to this is to surround the
* code with lguest_noirq_start: and lguest_noirq_end: labels. We tell the
* Host that it is *never* to interrupt us there, even if interrupts seem to be
* enabled. */
ENTRY(lguest_iret)
pushl %eax
movl 12(%esp), %eax
lguest_noirq_start:
/* Note the %ss: segment prefix here. Normal data accesses use the
* "ds" segment, but that will have already been restored for whatever
* we're returning to (such as userspace): we can't trust it. The %ss:
* prefix makes sure we use the stack segment, which is still valid. */
movl %eax,%ss:lguest_data+LGUEST_DATA_irq_enabled
popl %eax
iret
lguest_noirq_end:
|
