1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
#ifndef HOSTAP_CONFIG_H
#define HOSTAP_CONFIG_H
#define PRISM2_VERSION "CVS"
/* In the previous versions of Host AP driver, support for user space version
* of IEEE 802.11 management (hostapd) used to be disabled in the default
* configuration. From now on, support for hostapd is always included and it is
* possible to disable kernel driver version of IEEE 802.11 management with a
* separate define, PRISM2_NO_KERNEL_IEEE80211_MGMT. */
/* #define PRISM2_NO_KERNEL_IEEE80211_MGMT */
/* Maximum number of events handler per one interrupt */
#define PRISM2_MAX_INTERRUPT_EVENTS 20
/* Use PCI bus master to copy data to/from BAP (only available for
* hostap_pci.o).
*
* Note! This is extremely experimental. PCI bus master is not supported by
* Intersil and it seems to have some problems at least on TX path (see below).
* The driver code for implementing bus master support is based on guessing
* and experimenting suitable control bits and these might not be correct.
* This code is included because using bus master makes a huge difference in
* host CPU load (something like 40% host CPU usage to 5-10% when sending or
* receiving at maximum throughput).
*
* Note2! Station firmware version 1.3.5 and primary firmware version 1.0.7
* have some fixes for PCI corruption and these (or newer) versions are
* recommended especially when using bus mastering.
*
* NOTE: PCI bus mastering code has not been updated for long time and it is
* not likely to compile and it will _not_ work as is. Only enable this if you
* are prepared to first fix the implementation..
*/
/* #define PRISM2_BUS_MASTER */
#ifdef PRISM2_BUS_MASTER
/* PCI bus master implementation seems to be broken in current
* hardware/firmware versions. Enable this to use enable command to fix
* something before starting bus master operation on TX path. This will add
* some latency and an extra interrupt to each TX packet. */
#define PRISM2_ENABLE_BEFORE_TX_BUS_MASTER
#endif /* PRISM2_BUS_MASTER */
/* Include code for downloading firmware images into volatile RAM. */
#define PRISM2_DOWNLOAD_SUPPORT
/* Allow kernel configuration to enable download support. */
#if !defined(PRISM2_DOWNLOAD_SUPPORT) && defined(CONFIG_HOSTAP_FIRMWARE)
#define PRISM2_DOWNLOAD_SUPPORT
#endif
#ifdef PRISM2_DOWNLOAD_SUPPORT
/* Allow writing firmware images into flash, i.e., to non-volatile storage.
* Before you enable this option, you should make absolutely sure that you are
* using prism2_srec utility that comes with THIS version of the driver!
* In addition, please note that it is possible to kill your card with
* non-volatile download if you are using incorrect image. This feature has not
* been fully tested, so please be careful with it. */
/* #define PRISM2_NON_VOLATILE_DOWNLOAD */
#endif /* PRISM2_DOWNLOAD_SUPPORT */
/* Save low-level I/O for debugging. This should not be enabled in normal use.
*/
/* #define PRISM2_IO_DEBUG */
/* Following defines can be used to remove unneeded parts of the driver, e.g.,
* to limit the size of the kernel module. Definitions can be added here in
* hostap_config.h or they can be added to make command with EXTRA_CFLAGS,
* e.g.,
* 'make pccard EXTRA_CFLAGS="-DPRISM2_NO_DEBUG -DPRISM2_NO_PROCFS_DEBUG"'
*/
/* Do not include debug messages into the driver */
/* #define PRISM2_NO_DEBUG */
/* Do not include /proc/net/prism2/wlan#/{registers,debug} */
/* #define PRISM2_NO_PROCFS_DEBUG */
/* Do not include station functionality (i.e., allow only Master (Host AP) mode
*/
/* #define PRISM2_NO_STATION_MODES */
#endif /* HOSTAP_CONFIG_H */
|
