Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-for-linus-2.6

22 files changed, 1648 insertions, 146 deletions

diff --git a/Documentation/scsi/00-INDEX b/Documentation/scsi/00-INDEX
index f9cb5bdcce4..fef92ebf266 100644
--- a/Documentation/scsi/00-INDEX
+++ b/Documentation/scsi/00-INDEX
@@ -60,6 +60,8 @@ scsi.txt
 	- short blurb on using SCSI support as a module.
 scsi_mid_low_api.txt
 	- info on API between SCSI layer and low level drivers
+scsi_eh.txt
+	- info on SCSI midlayer error handling infrastructure
 st.txt
 	- info on scsi tape driver
 sym53c500_cs.txt
diff --git a/Documentation/scsi/scsi_eh.txt b/Documentation/scsi/scsi_eh.txt
new file mode 100644
index 00000000000..534a50922a7
--- /dev/null
+++ b/Documentation/scsi/scsi_eh.txt
@@ -0,0 +1,479 @@
+
+SCSI EH
+======================================
+
+ This document describes SCSI midlayer error handling infrastructure.
+Please refer to Documentation/scsi/scsi_mid_low_api.txt for more
+information regarding SCSI midlayer.
+
+TABLE OF CONTENTS
+
+[1] How SCSI commands travel through the midlayer and to EH
+    [1-1] struct scsi_cmnd
+    [1-2] How do scmd's get completed?
+	[1-2-1] Completing a scmd w/ scsi_done
+	[1-2-2] Completing a scmd w/ timeout
+    [1-3] How EH takes over
+[2] How SCSI EH works
+    [2-1] EH through fine-grained callbacks
+	[2-1-1] Overview
+	[2-1-2] Flow of scmds through EH
+	[2-1-3] Flow of control
+    [2-2] EH through hostt->eh_strategy_handler()
+	[2-2-1] Pre hostt->eh_strategy_handler() SCSI midlayer conditions
+	[2-2-2] Post hostt->eh_strategy_handler() SCSI midlayer conditions
+	[2-2-3] Things to consider
+
+
+[1] How SCSI commands travel through the midlayer and to EH
+
+[1-1] struct scsi_cmnd
+
+ Each SCSI command is represented with struct scsi_cmnd (== scmd).  A
+scmd has two list_head's to link itself into lists.  The two are
+scmd->list and scmd->eh_entry.  The former is used for free list or
+per-device allocated scmd list and not of much interest to this EH
+discussion.  The latter is used for completion and EH lists and unless
+otherwise stated scmds are always linked using scmd->eh_entry in this
+discussion.
+
+
+[1-2] How do scmd's get completed?
+
+ Once LLDD gets hold of a scmd, either the LLDD will complete the
+command by calling scsi_done callback passed from midlayer when
+invoking hostt->queuecommand() or SCSI midlayer will time it out.
+
+
+[1-2-1] Completing a scmd w/ scsi_done
+
+ For all non-EH commands, scsi_done() is the completion callback.  It
+does the following.
+
+ 1. Delete timeout timer.  If it fails, it means that timeout timer
+    has expired and is going to finish the command.  Just return.
+
+ 2. Link scmd to per-cpu scsi_done_q using scmd->en_entry
+
+ 3. Raise SCSI_SOFTIRQ
+
+ SCSI_SOFTIRQ handler scsi_softirq calls scsi_decide_disposition() to
+determine what to do with the command.  scsi_decide_disposition()
+looks at the scmd->result value and sense data to determine what to do
+with the command.
+
+ - SUCCESS
+	scsi_finish_command() is invoked for the command.  The
+	function does some maintenance choirs and notify completion by
+	calling scmd->done() callback, which, for fs requests, would
+	be HLD completion callback - sd:sd_rw_intr, sr:rw_intr,
+	st:st_intr.
+
+ - NEEDS_RETRY
+ - ADD_TO_MLQUEUE
+	scmd is requeued to blk queue.
+
+ - otherwise
+	scsi_eh_scmd_add(scmd, 0) is invoked for the command.  See
+	[1-3] for details of this funciton.
+
+
+[1-2-2] Completing a scmd w/ timeout
+
+ The timeout handler is scsi_times_out().  When a timeout occurs, this
+function
+
+ 1. invokes optional hostt->eh_timedout() callback.  Return value can
+    be one of
+
+    - EH_HANDLED
+	This indicates that eh_timedout() dealt with the timeout.  The
+	scmd is passed to __scsi_done() and thus linked into per-cpu
+	scsi_done_q.  Normal command completion described in [1-2-1]
+	follows.
+
+    - EH_RESET_TIMER
+	This indicates that more time is required to finish the
+	command.  Timer is restarted.  This action is counted as a
+	retry and only allowed scmd->allowed + 1(!) times.  Once the
+	limit is reached, action for EH_NOT_HANDLED is taken instead.
+
+	*NOTE* This action is racy as the LLDD could finish the scmd
+	after the timeout has expired but before it's added back.  In
+	such cases, scsi_done() would think that timeout has occurred
+	and return without doing anything.  We lose completion and the
+	command will time out again.
+
+    - EH_NOT_HANDLED
+	This is the same as when eh_timedout() callback doesn't exist.
+	Step #2 is taken.
+
+ 2. scsi_eh_scmd_add(scmd, SCSI_EH_CANCEL_CMD) is invoked for the
+    command.  See [1-3] for more information.
+
+
+[1-3] How EH takes over
+
+ scmds enter EH via scsi_eh_scmd_add(), which does the following.
+
+ 1. Turns on scmd->eh_eflags as requested.  It's 0 for error
+    completions and SCSI_EH_CANCEL_CMD for timeouts.
+
+ 2. Links scmd->eh_entry to shost->eh_cmd_q
+
+ 3. Sets SHOST_RECOVERY bit in shost->shost_state
+
+ 4. Increments shost->host_failed
+
+ 5. Wakes up SCSI EH thread if shost->host_busy == shost->host_failed
+
+ As can be seen above, once any scmd is added to shost->eh_cmd_q,
+SHOST_RECOVERY shost_state bit is turned on.  This prevents any new
+scmd to be issued from blk queue to the host; eventually, all scmds on
+the host either complete normally, fail and get added to eh_cmd_q, or
+time out and get added to shost->eh_cmd_q.
+
+ If all scmds either complete or fail, the number of in-flight scmds
+becomes equal to the number of failed scmds - i.e. shost->host_busy ==
+shost->host_failed.  This wakes up SCSI EH thread.  So, once woken up,
+SCSI EH thread can expect that all in-flight commands have failed and
+are linked on shost->eh_cmd_q.
+
+ Note that this does not mean lower layers are quiescent.  If a LLDD
+completed a scmd with error status, the LLDD and lower layers are
+assumed to forget about the scmd at that point.  However, if a scmd
+has timed out, unless hostt->eh_timedout() made lower layers forget
+about the scmd, which currently no LLDD does, the command is still
+active as long as lower layers are concerned and completion could
+occur at any time.  Of course, all such completions are ignored as the
+timer has already expired.
+
+ We'll talk about how SCSI EH takes actions to abort - make LLDD
+forget about - timed out scmds later.
+
+
+[2] How SCSI EH works
+
+ LLDD's can implement SCSI EH actions in one of the following two
+ways.
+
+ - Fine-grained EH callbacks
+	LLDD can implement fine-grained EH callbacks and let SCSI
+	midlayer drive error handling and call appropriate callbacks.
+	This will be dicussed further in [2-1].
+
+ - eh_strategy_handler() callback
+	This is one big callback which should perform whole error
+	handling.  As such, it should do all choirs SCSI midlayer
+	performs during recovery.  This will be discussed in [2-2].
+
+ Once recovery is complete, SCSI EH resumes normal operation by
+calling scsi_restart_operations(), which
+
+ 1. Checks if door locking is needed and locks door.
+
+ 2. Clears SHOST_RECOVERY shost_state bit
+
+ 3. Wakes up waiters on shost->host_wait.  This occurs if someone
+    calls scsi_block_when_processing_errors() on the host.
+    (*QUESTION* why is it needed?  All operations will be blocked
+    anyway after it reaches blk queue.)
+
+ 4. Kicks queues in all devices on the host in the asses
+
+
+[2-1] EH through fine-grained callbacks
+
+[2-1-1] Overview
+
+ If eh_strategy_handler() is not present, SCSI midlayer takes charge
+of driving error handling.  EH's goals are two - make LLDD, host and
+device forget about timed out scmds and make them ready for new
+commands.  A scmd is said to be recovered if the scmd is forgotten by
+lower layers and lower layers are ready to process or fail the scmd
+again.
+
+ To achieve these goals, EH performs recovery actions with increasing
+severity.  Some actions are performed by issueing SCSI commands and
+others are performed by invoking one of the following fine-grained
+hostt EH callbacks.  Callbacks may be omitted and omitted ones are
+considered to fail always.
+
+int (* eh_abort_handler)(struct scsi_cmnd *);
+int (* eh_device_reset_handler)(struct scsi_cmnd *);
+int (* eh_bus_reset_handler)(struct scsi_cmnd *);
+int (* eh_host_reset_handler)(struct scsi_cmnd *);
+
+ Higher-severity actions are taken only when lower-severity actions
+cannot recover some of failed scmds.  Also, note that failure of the
+highest-severity action means EH failure and results in offlining of
+all unrecovered devices.
+
+ During recovery, the following rules are followed
+
+ - Recovery actions are performed on failed scmds on the to do list,
+   eh_work_q.  If a recovery action succeeds for a scmd, recovered
+   scmds are removed from eh_work_q.
+
+   Note that single recovery action on a scmd can recover multiple
+   scmds.  e.g. resetting a device recovers all failed scmds on the
+   device.
+
+ - Higher severity actions are taken iff eh_work_q is not empty after
+   lower severity actions are complete.
+
+ - EH reuses failed scmds to issue commands for recovery.  For
+   timed-out scmds, SCSI EH ensures that LLDD forgets about a scmd
+   before reusing it for EH commands.
+
+ When a scmd is recovered, the scmd is moved from eh_work_q to EH
+local eh_done_q using scsi_eh_finish_cmd().  After all scmds are
+recovered (eh_work_q is empty), scsi_eh_flush_done_q() is invoked to
+either retry or error-finish (notify upper layer of failure) recovered
+scmds.
+
+ scmds are retried iff its sdev is still online (not offlined during
+EH), REQ_FAILFAST is not set and ++scmd->retries is less than
+scmd->allowed.
+
+
+[2-1-2] Flow of scmds through EH
+
+ 1. Error completion / time out
+    ACTION: scsi_eh_scmd_add() is invoked for scmd
+	- set scmd->eh_eflags
+	- add scmd to shost->eh_cmd_q
+	- set SHOST_RECOVERY
+	- shost->host_failed++
+    LOCKING: shost->host_lock
+
+ 2. EH starts
+    ACTION: move all scmds to EH's local eh_work_q.  shost->eh_cmd_q
+	    is cleared.
+    LOCKING: shost->host_lock (not strictly necessary, just for
+             consistency)
+
+ 3. scmd recovered
+    ACTION: scsi_eh_finish_cmd() is invoked to EH-finish scmd
+	- shost->host_failed--
+	- clear scmd->eh_eflags
+	- scsi_setup_cmd_retry()
+	- move from local eh_work_q to local eh_done_q
+    LOCKING: none
+
+ 4. EH completes
+    ACTION: scsi_eh_flush_done_q() retries scmds or notifies upper
+	    layer of failure.
+	- scmd is removed from eh_done_q and scmd->eh_entry is cleared
+	- if retry is necessary, scmd is requeued using
+          scsi_queue_insert()
+	- otherwise, scsi_finish_command() is invoked for scmd
+    LOCKING: queue or finish function performs appropriate locking
+
+
+[2-1-3] Flow of control
+
+ EH through fine-grained callbacks start from scsi_unjam_host().
+
+<<scsi_unjam_host>>
+
+    1. Lock shost->host_lock, splice_init shost->eh_cmd_q into local
+       eh_work_q and unlock host_lock.  Note that shost->eh_cmd_q is
+       cleared by this action.
+
+    2. Invoke scsi_eh_get_sense.
+
+    <<scsi_eh_get_sense>>
+
+	This action is taken for each error-completed
+	(!SCSI_EH_CANCEL_CMD) commands without valid sense data.  Most
+	SCSI transports/LLDDs automatically acquire sense data on
+	command failures (autosense).  Autosense is recommended for
+	performance reasons and as sense information could get out of
+	sync inbetween occurrence of CHECK CONDITION and this action.
+
+	Note that if autosense is not supported, scmd->sense_buffer
+	contains invalid sense data when error-completing the scmd
+	with scsi_done().  scsi_decide_disposition() always returns
+	FAILED in such cases thus invoking SCSI EH.  When the scmd
+	reaches here, sense data is acquired and
+	scsi_decide_disposition() is called again.
+
+	1. Invoke scsi_request_sense() which issues REQUEST_SENSE
+           command.  If fails, no action.  Note that taking no action
+           causes higher-severity recovery to be taken for the scmd.
+
+	2. Invoke scsi_decide_disposition() on the scmd
+
+	   - SUCCESS
+		scmd->retries is set to scmd->allowed preventing
+		scsi_eh_flush_done_q() from retrying the scmd and
+		scsi_eh_finish_cmd() is invoked.
+
+	   - NEEDS_RETRY
+		scsi_eh_finish_cmd() invoked
+
+	   - otherwise
+		No action.
+
+    3. If !list_empty(&eh_work_q), invoke scsi_eh_abort_cmds().
+
+    <<scsi_eh_abort_cmds>>
+
+	This action is taken for each timed out command.
+	hostt->eh_abort_handler() is invoked for each scmd.  The
+	handler returns SUCCESS if it has succeeded to make LLDD and
+	all related hardware forget about the scmd.
+
+	If a timedout scmd is successfully aborted and the sdev is
+	either offline or ready, scsi_eh_finish_cmd() is invoked for
+	the scmd.  Otherwise, the scmd is left in eh_work_q for
+	higher-severity actions.
+
+	Note that both offline and ready status mean that the sdev is
+	ready to process new scmds, where processing also implies
+	immediate failing; thus, if a sdev is in one of the two
+	states, no further recovery action is needed.
+
+	Device readiness is tested using scsi_eh_tur() which issues
+	TEST_UNIT_READY command.  Note that the scmd must have been
+	aborted successfully before reusing it for TEST_UNIT_READY.
+
+    4. If !list_empty(&eh_work_q), invoke scsi_eh_ready_devs()
+
+    <<scsi_eh_ready_devs>>
+
+	This function takes four increasingly more severe measures to
+	make failed sdevs ready for new commands.
+
+	1. Invoke scsi_eh_stu()
+
+	<<scsi_eh_stu>>
+
+	    For each sdev which has failed scmds with valid sense data
+	    of which scsi_check_sense()'s verdict is FAILED,
+	    START_STOP_UNIT command is issued w/ start=1.  Note that
+	    as we explicitly choose error-completed scmds, it is known
+	    that lower layers have forgotten about the scmd and we can
+	    reuse it for STU.
+
+	    If STU succeeds and the sdev is either offline or ready,
+	    all failed scmds on the sdev are EH-finished with
+	    scsi_eh_finish_cmd().
+
+	    *NOTE* If hostt->eh_abort_handler() isn't implemented or
+	    failed, we may still have timed out scmds at this point
+	    and STU doesn't make lower layers forget about those
+	    scmds.  Yet, this function EH-finish all scmds on the sdev
+	    if STU succeeds leaving lower layers in an inconsistent
+	    state.  It seems that STU action should be taken only when
+	    a sdev has no timed out scmd.
+
+	2. If !list_empty(&eh_work_q), invoke scsi_eh_bus_device_reset().
+
+	<<scsi_eh_bus_device_reset>>
+
+	    This action is very similar to scsi_eh_stu() except that,
+	    instead of issuing STU, hostt->eh_device_reset_handler()
+	    is used.  Also, as we're not issuing SCSI commands and
+	    resetting clears all scmds on the sdev, there is no need
+	    to choose error-completed scmds.
+
+	3. If !list_empty(&eh_work_q), invoke scsi_eh_bus_reset()
+
+	<<scsi_eh_bus_reset>>
+
+	    hostt->eh_bus_reset_handler() is invoked for each channel
+	    with failed scmds.  If bus reset succeeds, all failed
+	    scmds on all ready or offline sdevs on the channel are
+	    EH-finished.
+
+	4. If !list_empty(&eh_work_q), invoke scsi_eh_host_reset()
+
+	<<scsi_eh_host_reset>>
+
+	    This is the last resort.  hostt->eh_host_reset_handler()
+	    is invoked.  If host reset succeeds, all failed scmds on
+	    all ready or offline sdevs on the host are EH-finished.
+
+	5. If !list_empty(&eh_work_q), invoke scsi_eh_offline_sdevs()
+
+	<<scsi_eh_offline_sdevs>>
+
+	    Take all sdevs which still have unrecovered scmds offline
+	    and EH-finish the scmds.
+
+    5. Invoke scsi_eh_flush_done_q().
+
+	<<scsi_eh_flush_done_q>>
+
+	    At this point all scmds are recovered (or given up) and
+	    put on eh_done_q by scsi_eh_finish_cmd().  This function
+	    flushes eh_done_q by either retrying or notifying upper
+	    layer of failure of the scmds.
+
+
+[2-2] EH through hostt->eh_strategy_handler()
+
+ hostt->eh_strategy_handler() is invoked in the place of
+scsi_unjam_host() and it is responsible for whole recovery process.
+On completion, the handler should have made lower layers forget about
+all failed scmds and either ready for new commands or offline.  Also,
+it should perform SCSI EH maintenance choirs to maintain integrity of
+SCSI midlayer.  IOW, of the steps described in [2-1-2], all steps
+except for #1 must be implemented by eh_strategy_handler().
+
+
+[2-2-1] Pre hostt->eh_strategy_handler() SCSI midlayer conditions
+
+ The following conditions are true on entry to the handler.
+
+ - Each failed scmd's eh_flags field is set appropriately.
+
+ - Each failed scmd is linked on scmd->eh_cmd_q by scmd->eh_entry.
+
+ - SHOST_RECOVERY is set.
+
+ - shost->host_failed == shost->host_busy
+
+
+[2-2-2] Post hostt->eh_strategy_handler() SCSI midlayer conditions
+
+ The following conditions must be true on exit from the handler.
+
+ - shost->host_failed is zero.
+
+ - Each scmd's eh_eflags field is cleared.
+
+ - Each scmd is in such a state that scsi_setup_cmd_retry() on the
+   scmd doesn't make any difference.
+
+ - shost->eh_cmd_q is cleared.
+
+ - Each scmd->eh_entry is cleared.
+
+ - Either scsi_queue_insert() or scsi_finish_command() is called on
+   each scmd.  Note that the handler is free to use scmd->retries and
+   ->allowed to limit the number of retries.
+
+
+[2-2-3] Things to consider
+
+ - Know that timed out scmds are still active on lower layers.  Make
+   lower layers forget about them before doing anything else with
+   those scmds.
+
+ - For consistency, when accessing/modifying shost data structure,
+   grab shost->host_lock.
+
+ - On completion, each failed sdev must have forgotten about all
+   active scmds.
+
+ - On completion, each failed sdev must be ready for new commands or
+   offline.
+
+
+--
+Tejun Heo
+htejun@gmail.com
+11th September 2005
diff --git a/drivers/block/scsi_ioctl.c b/drivers/block/scsi_ioctl.c
index abb2df249fd..856c2278e9d 100644
--- a/drivers/block/scsi_ioctl.c
+++ b/drivers/block/scsi_ioctl.c
@@ -123,6 +123,7 @@ static int verify_command(struct file *file, unsigned char *cmd)
 		safe_for_read(READ_12),
 		safe_for_read(READ_16),
 		safe_for_read(READ_BUFFER),
+		safe_for_read(READ_DEFECT_DATA),
 		safe_for_read(READ_LONG),
 		safe_for_read(INQUIRY),
 		safe_for_read(MODE_SENSE),
diff --git a/drivers/ieee1394/sbp2.c b/drivers/ieee1394/sbp2.c
index 627af507643..de88218ef7c 100644
--- a/drivers/ieee1394/sbp2.c
+++ b/drivers/ieee1394/sbp2.c
@@ -790,7 +790,7 @@ static void sbp2_host_reset(struct hpsb_host *host)
 static int sbp2_start_device(struct scsi_id_instance_data *scsi_id)
 {
 	struct sbp2scsi_host_info *hi = scsi_id->hi;
-	struct scsi_device *sdev;
+	int error;
 
 	SBP2_DEBUG("sbp2_start_device");
 
@@ -939,10 +939,10 @@ alloc_fail:
 	sbp2_max_speed_and_size(scsi_id);
 
 	/* Add this device to the scsi layer now */
-	sdev = scsi_add_device(scsi_id->scsi_host, 0, scsi_id->ud->id, 0);
-	if (IS_ERR(sdev)) {
+	error = scsi_add_device(scsi_id->scsi_host, 0, scsi_id->ud->id, 0);
+	if (error) {
 		SBP2_ERR("scsi_add_device failed");
-		return PTR_ERR(sdev);
+		return error;
 	}
 
 	return 0;
diff --git a/drivers/scsi/3w-9xxx.c b/drivers/scsi/3w-9xxx.c
index bc6e4627c7a..a6ac61611f3 100644
--- a/drivers/scsi/3w-9xxx.c
+++ b/drivers/scsi/3w-9xxx.c
@@ -59,6 +59,7 @@
                  Fix 'handled=1' ISR usage, remove bogus IRQ check.
                  Remove un-needed eh_abort handler.
                  Add support for embedded firmware error strings.
+   2.26.02.003 - Correctly handle single sgl's with use_sg=1.
 */
 
 #include <linux/module.h>
@@ -81,7 +82,7 @@
 #include "3w-9xxx.h"
 
 /* Globals */
-#define TW_DRIVER_VERSION "2.26.02.002"
+#define TW_DRIVER_VERSION "2.26.02.003"
 static TW_Device_Extension *twa_device_extension_list[TW_MAX_SLOT];
 static unsigned int twa_device_extension_count;
 static int twa_major = -1;
@@ -1805,6 +1806,8 @@ static int twa_scsiop_execute_scsi(TW_Device_Extension *tw_dev, int request_id,
 			if (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH) {
 				command_packet->sg_list[0].address = tw_dev->generic_buffer_phys[request_id];
 				command_packet->sg_list[0].length = TW_MIN_SGL_LENGTH;
+				if (tw_dev->srb[request_id]->sc_data_direction == DMA_TO_DEVICE || tw_dev->srb[request_id]->sc_data_direction == DMA_BIDIRECTIONAL)
+					memcpy(tw_dev->generic_buffer_virt[request_id], tw_dev->srb[request_id]->request_buffer, tw_dev->srb[request_id]->request_bufflen);
 			} else {
 				buffaddr = twa_map_scsi_single_data(tw_dev, request_id);
 				if (buffaddr == 0)
@@ -1823,6 +1826,12 @@ static int twa_scsiop_execute_scsi(TW_Device_Extension *tw_dev, int request_id,
 
 		if (tw_dev->srb[request_id]->use_sg > 0) {
 			if ((tw_dev->srb[request_id]->use_sg == 1) && (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH)) {
+				if (tw_dev->srb[request_id]->sc_data_direction == DMA_TO_DEVICE || tw_dev->srb[request_id]->sc_data_direction == DMA_BIDIRECTIONAL) {
+					struct scatterlist *sg = (struct scatterlist *)tw_dev->srb[request_id]->request_buffer;
+					char *buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset;
+					memcpy(tw_dev->generic_buffer_virt[request_id], buf, sg->length);
+					kunmap_atomic(buf - sg->offset, KM_IRQ0);
+				}
 				command_packet->sg_list[0].address = tw_dev->generic_buffer_phys[request_id];
 				command_packet->sg_list[0].length = TW_MIN_SGL_LENGTH;
 			} else {
@@ -1888,11 +1897,20 @@ out:
 /* This function completes an execute scsi operation */
 static void twa_scsiop_execute_scsi_complete(TW_Device_Extension *tw_dev, int request_id)
 {
-	/* Copy the response if too small */
-	if ((tw_dev->srb[request_id]->request_buffer) && (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH)) {
-		memcpy(tw_dev->srb[request_id]->request_buffer,
-		       tw_dev->generic_buffer_virt[request_id],
-		       tw_dev->srb[request_id]->request_bufflen);
+	if (tw_dev->srb[request_id]->request_bufflen < TW_MIN_SGL_LENGTH &&
+	    (tw_dev->srb[request_id]->sc_data_direction == DMA_FROM_DEVICE ||
+	     tw_dev->srb[request_id]->sc_data_direction == DMA_BIDIRECTIONAL)) {
+		if (tw_dev->srb[request_id]->use_sg == 0) {
+			memcpy(tw_dev->srb[request_id]->request_buffer,
+			       tw_dev->generic_buffer_virt[request_id],
+			       tw_dev->srb[request_id]->request_bufflen);
+		}
+		if (tw_dev->srb[request_id]->use_sg == 1) {
+			struct scatterlist *sg = (struct scatterlist *)tw_dev->srb[request_id]->request_buffer;
+			char *buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset;
+			memcpy(buf, tw_dev->generic_buffer_virt[request_id], sg->length);
+			kunmap_atomic(buf - sg->offset, KM_IRQ0);
+		}
 	}
 } /* End twa_scsiop_execute_scsi_complete() */
 
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 2d21265e650..20019b82b4a 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -235,6 +235,13 @@ config SCSI_ISCSI_ATTRS
 	  each attached iSCSI device to sysfs, say Y.
 	  Otherwise, say N.
 
+config SCSI_SAS_ATTRS
+	tristate "SAS Transport Attributes"
+	depends on SCSI
+	help
+	  If you wish to export transport-specific information about
+	  each attached SAS device to sysfs, say Y.
+
 endmenu
 
 menu "SCSI low-level drivers"
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
index 4b4fd94c267..1e4edbdf273 100644
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_RAID_ATTRS)	+= raid_class.o
 obj-$(CONFIG_SCSI_SPI_ATTRS)	+= scsi_transport_spi.o
 obj-$(CONFIG_SCSI_FC_ATTRS) 	+= scsi_transport_fc.o
 obj-$(CONFIG_SCSI_ISCSI_ATTRS)	+= scsi_transport_iscsi.o
+obj-$(CONFIG_SCSI_SAS_ATTRS)	+= scsi_transport_sas.o
 
 obj-$(CONFIG_SCSI_AMIGA7XX)	+= amiga7xx.o	53c7xx.o
 obj-$(CONFIG_A3000_SCSI)	+= a3000.o	wd33c93.o
diff --git a/drivers/scsi/lpfc/lpfc_attr.c b/drivers/scsi/lpfc/lpfc_attr.c
index 0e089a42c03..86eaf6d408d 100644
--- a/drivers/scsi/lpfc/lpfc_attr.c
+++ b/drivers/scsi/lpfc/lpfc_attr.c
@@ -966,21 +966,21 @@ static void
 lpfc_get_host_fabric_name (struct Scsi_Host *shost)
 {
 	struct lpfc_hba *phba = (struct lpfc_hba*)shost->hostdata[0];
-	u64 nodename;
+	u64 node_name;
 
 	spin_lock_irq(shost->host_lock);
 
 	if ((phba->fc_flag & FC_FABRIC) ||
 	    ((phba->fc_topology == TOPOLOGY_LOOP) &&
 	     (phba->fc_flag & FC_PUBLIC_LOOP)))
-		memcpy(&nodename, &phba->fc_fabparam.nodeName, sizeof(u64));
+		node_name = wwn_to_u64(phba->fc_fabparam.nodeName.wwn);
 	else
 		/* fabric is local port if there is no F/FL_Port */
-		memcpy(&nodename, &phba->fc_nodename, sizeof(u64));
+		node_name = wwn_to_u64(phba->fc_nodename.wwn);
 
 	spin_unlock_irq(shost->host_lock);
 
-	fc_host_fabric_name(shost) = be64_to_cpu(nodename);
+	fc_host_fabric_name(shost) = node_name;
 }
 
 
@@ -1103,21 +1103,20 @@ lpfc_get_starget_node_name(struct scsi_target *starget)
 {
 	struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
 	struct lpfc_hba *phba = (struct lpfc_hba *) shost->hostdata[0];
-	uint64_t node_name = 0;
+	u64 node_name = 0;
 	struct lpfc_nodelist *ndlp = NULL;
 
 	spin_lock_irq(shost->host_lock);
 	/* Search the mapped list for this target ID */
 	list_for_each_entry(ndlp, &phba->fc_nlpmap_list, nlp_listp) {
 		if (starget->id == ndlp->nlp_sid) {
-			memcpy(&node_name, &ndlp->nlp_nodename,
-						sizeof(struct lpfc_name));
+			node_name = wwn_to_u64(ndlp->nlp_nodename.wwn);
 			break;
 		}
 	}
 	spin_unlock_irq(shost->host_lock);
 
-	fc_starget_node_name(starget) = be64_to_cpu(node_name);
+	fc_starget_node_name(starget) = node_name;
 }
 
 static void
@@ -1125,21 +1124,20 @@ lpfc_get_starget_port_name(struct scsi_target *starget)
 {
 	struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
 	struct lpfc_hba *phba = (struct lpfc_hba *) shost->hostdata[0];
-	uint64_t port_name = 0;
+	u64 port_name = 0;
 	struct lpfc_nodelist *ndlp = NULL;
 
 	spin_lock_irq(shost->host_lock);
 	/* Search the mapped list for this target ID */
 	list_for_each_entry(ndlp, &phba->fc_nlpmap_list, nlp_listp) {
 		if (starget->id == ndlp->nlp_sid) {
-			memcpy(&port_name, &ndlp->nlp_portname,
-						sizeof(struct lpfc_name));
+			port_name = wwn_to_u64(ndlp->nlp_portname.wwn);
 			break;
 		}
 	}
 	spin_unlock_irq(shost->host_lock);
 
-	fc_starget_port_name(starget) = be64_to_cpu(port_name);
+	fc_starget_port_name(starget) = port_name;
 }
 
 static void
diff --git a/drivers/scsi/lpfc/lpfc_hbadisc.c b/drivers/scsi/lpfc/lpfc_hbadisc.c
index 0a8269d6b13..4fb8eb0c84c 100644
--- a/drivers/scsi/lpfc/lpfc_hbadisc.c
+++ b/drivers/scsi/lpfc/lpfc_hbadisc.c
@@ -1017,13 +1017,10 @@ lpfc_register_remote_port(struct lpfc_hba * phba,
 	struct fc_rport *rport;
 	struct lpfc_rport_data *rdata;
 	struct fc_rport_identifiers rport_ids;
-	uint64_t wwn;
 
 	/* Remote port has reappeared. Re-register w/ FC transport */
-	memcpy(&wwn, &ndlp->nlp_nodename, sizeof(uint64_t));
-	rport_ids.node_name = be64_to_cpu(wwn);
-	memcpy(&wwn, &ndlp->nlp_portname, sizeof(uint64_t));
-	rport_ids.port_name = be64_to_cpu(wwn);
+	rport_ids.node_name = wwn_to_u64(ndlp->nlp_nodename.wwn);
+	rport_ids.port_name = wwn_to_u64(ndlp->nlp_portname.wwn);
 	rport_ids.port_id = ndlp->nlp_DID;
 	rport_ids.roles = FC_RPORT_ROLE_UNKNOWN;
 	if (ndlp->nlp_type & NLP_FCP_TARGET)
diff --git a/drivers/scsi/lpfc/lpfc_hw.h b/drivers/scsi/lpfc/lpfc_hw.h
index 21591cb9f55..047a87c26cc 100644
--- a/drivers/scsi/lpfc/lpfc_hw.h
+++ b/drivers/scsi/lpfc/lpfc_hw.h
@@ -262,12 +262,14 @@ struct lpfc_sli_ct_request {
 #define FF_FRAME_SIZE     2048
 
 struct lpfc_name {
+	union {
+		struct {
 #ifdef __BIG_ENDIAN_BITFIELD
-	uint8_t nameType:4;	/* FC Word 0, bit 28:31 */
-	uint8_t IEEEextMsn:4;	/* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */
+			uint8_t nameType:4;	/* FC Word 0, bit 28:31 */
+			uint8_t IEEEextMsn:4;	/* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */
 #else	/*  __LITTLE_ENDIAN_BITFIELD */
-	uint8_t IEEEextMsn:4;	/* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */
-	uint8_t nameType:4;	/* FC Word 0, bit 28:31 */
+			uint8_t IEEEextMsn:4;	/* FC Word 0, bit 24:27, bit 8:11 of IEEE ext */
+			uint8_t nameType:4;	/* FC Word 0, bit 28:31 */
 #endif
 
 #define NAME_IEEE           0x1	/* IEEE name - nameType */
@@ -276,8 +278,11 @@ struct lpfc_name {
 #define NAME_IP_TYPE        0x4	/* IP address */
 #define NAME_CCITT_TYPE     0xC
 #define NAME_CCITT_GR_TYPE  0xE
-	uint8_t IEEEextLsb;	/* FC Word 0, bit 16:23, IEEE extended Lsb */
-	uint8_t IEEE[6];	/* FC IEEE address */
+			uint8_t IEEEextLsb;	/* FC Word 0, bit 16:23, IEEE extended Lsb */
+			uint8_t IEEE[6];	/* FC IEEE address */
+		};
+		uint8_t wwn[8];
+	};
 };
 
 struct csp {
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index 6f3cb59bf9e..454058f655d 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -1333,7 +1333,6 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid)
 	unsigned long bar0map_len, bar2map_len;
 	int error = -ENODEV, retval;
 	int i;
-	u64 wwname;
 
 	if (pci_enable_device(pdev))
 		goto out;
@@ -1524,10 +1523,8 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid)
 	 * Must done after lpfc_sli_hba_setup()
 	 */
 
-	memcpy(&wwname, &phba->fc_nodename, sizeof(u64));
-	fc_host_node_name(host) = be64_to_cpu(wwname);
-	memcpy(&wwname, &phba->fc_portname, sizeof(u64));
-	fc_host_port_name(host) = be64_to_cpu(wwname);
+	fc_host_node_name(host) = wwn_to_u64(phba->fc_nodename.wwn);
+	fc_host_port_name(host) = wwn_to_u64(phba->fc_portname.wwn);
 	fc_host_supported_classes(host) = FC_COS_CLASS3;
 
 	memset(fc_host_supported_fc4s(host), 0,
diff --git a/drivers/scsi/qla2xxx/qla_attr.c b/drivers/scsi/qla2xxx/qla_attr.c
index fe0fce71adc..fc25cd83466 100644
--- a/drivers/scsi/qla2xxx/qla_attr.c
+++ b/drivers/scsi/qla2xxx/qla_attr.c
@@ -360,16 +360,16 @@ qla2x00_get_starget_node_name(struct scsi_target *starget)
 	struct Scsi_Host *host = dev_to_shost(starget->dev.parent);
 	scsi_qla_host_t *ha = to_qla_host(host);
 	fc_port_t *fcport;
-	uint64_t node_name = 0;
+	u64 node_name = 0;
 
 	list_for_each_entry(fcport, &ha->fcports, list) {
 		if (starget->id == fcport->os_target_id) {
-			node_name = *(uint64_t *)fcport->node_name;
+			node_name = wwn_to_u64(fcport->node_name);
 			break;
 		}
 	}
 
-	fc_starget_node_name(starget) = be64_to_cpu(node_name);
+	fc_starget_node_name(starget) = node_name;
 }
 
 static void
@@ -378,16 +378,16 @@ qla2x00_get_starget_port_name(struct scsi_target *starget)
 	struct Scsi_Host *host = dev_to_shost(starget->dev.parent);
 	scsi_qla_host_t *ha = to_qla_host(host);
 	fc_port_t *fcport;
-	uint64_t port_name = 0;
+	u64 port_name = 0;
 
 	list_for_each_entry(fcport, &ha->fcports, list) {
 		if (starget->id == fcport->os_target_id) {
-			port_name = *(uint64_t *)fcport->port_name;
+			port_name = wwn_to_u64(fcport->port_name);
 			break;
 		}
 	}
 
-	fc_starget_port_name(starget) = be64_to_cpu(port_name);
+	fc_starget_port_name(starget) = port_name;
 }
 
 static void
@@ -460,9 +460,7 @@ struct fc_function_template qla2xxx_transport_functions = {
 void
 qla2x00_init_host_attr(scsi_qla_host_t *ha)
 {
-	fc_host_node_name(ha->host) =
-	    be64_to_cpu(*(uint64_t *)ha->init_cb->node_name);
-	fc_host_port_name(ha->host) =
-	    be64_to_cpu(*(uint64_t *)ha->init_cb->port_name);
+	fc_host_node_name(ha->host) = wwn_to_u64(ha->init_cb->node_name);
+	fc_host_port_name(ha->host) = wwn_to_u64(ha->init_cb->port_name);
 	fc_host_supported_classes(ha->host) = FC_COS_CLASS3;
 }
diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c
index c619583e646..3e9b6413787 100644
--- a/drivers/scsi/qla2xxx/qla_init.c
+++ b/drivers/scsi/qla2xxx/qla_init.c
@@ -2066,8 +2066,8 @@ qla2x00_reg_remote_port(scsi_qla_host_t *ha, fc_port_t *fcport)
 		return;
 	}
 
-	rport_ids.node_name = be64_to_cpu(*(uint64_t *)fcport->node_name);
-	rport_ids.port_name = be64_to_cpu(*(uint64_t *)fcport->port_name);
+	rport_ids.node_name = wwn_to_u64(fcport->node_name);
+	rport_ids.port_name = wwn_to_u64(fcport->port_name);
 	rport_ids.port_id = fcport->d_id.b.domain << 16 |
 	    fcport->d_id.b.area << 8 | fcport->d_id.b.al_pa;
 	rport_ids.roles = FC_RPORT_ROLE_UNKNOWN;
diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index 77f2d444f7e..863bb6495da 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -97,6 +97,30 @@ int scsi_insert_special_req(struct scsi_request *sreq, int at_head)
 }
 
 static void scsi_run_queue(struct request_queue *q);
+static void scsi_release_buffers(struct scsi_cmnd *cmd);
+
+/*
+ * Function:	scsi_unprep_request()
+ *
+ * Purpose:	Remove all preparation done for a request, including its
+ *		associated scsi_cmnd, so that it can be requeued.
+ *
+ * Arguments:	req	- request to unprepare
+ *
+ * Lock status:	Assumed that no locks are held upon entry.
+ *
+ * Returns:	Nothing.
+ */
+static void scsi_unprep_request(struct request *req)
+{
+	struct scsi_cmnd *cmd = req->special;
+
+	req->flags &= ~REQ_DONTPREP;
+	req->special = (req->flags & REQ_SPECIAL) ? cmd->sc_request : NULL;
+
+	scsi_release_buffers(cmd);
+	scsi_put_command(cmd);
+}
 
 /*
  * Function:    scsi_queue_insert()
@@ -116,12 +140,14 @@ static void scsi_run_queue(struct request_queue *q);
  *              commands.
  * Notes:       This could be called either from an interrupt context or a
  *              normal process context.
+ * Notes:	Upon return, cmd is a stale pointer.
  */
 int scsi_queue_insert(struct scsi_cmnd *cmd, int reason)
 {
 	struct Scsi_Host *host = cmd->device->host;
 	struct scsi_device *device = cmd->device;
 	struct request_queue *q = device->request_queue;
+	struct request *req = cmd->request;
 	unsigned long flags;
 
 	SCSI_LOG_MLQUEUE(1,
@@ -162,8 +188,9 @@ int scsi_queue_insert(struct scsi_cmnd *cmd, int reason)
 	 * function.  The SCSI request function detects the blocked condition
 	 * and plugs the queue appropriately.
          */
+	scsi_unprep_request(req);
 	spin_lock_irqsave(q->queue_lock, flags);
-	blk_requeue_request(q, cmd->request);
+	blk_requeue_request(q, req);
 	spin_unlock_irqrestore(q->queue_lock, flags);
 
 	scsi_run_queue(q);
@@ -339,7 +366,7 @@ int scsi_execute_req(struct scsi_device *sdev, const unsigned char *cmd,
 	int result;
 	
 	if (sshdr) {
-		sense = kmalloc(SCSI_SENSE_BUFFERSIZE, GFP_KERNEL);
+		sense = kmalloc(SCSI_SENSE_BUFFERSIZE, GFP_NOIO);
 		if (!sense)
 			return DRIVER_ERROR << 24;
 		memset(sense, 0, SCSI_SENSE_BUFFERSIZE);
@@ -552,15 +579,16 @@ static void scsi_run_queue(struct request_queue *q)
  *		I/O errors in the middle of the request, in which case
  *		we need to request the blocks that come after the bad
  *		sector.
+ * Notes:	Upon return, cmd is a stale pointer.
  */
 static void scsi_requeue_command(struct request_queue *q, struct scsi_cmnd *cmd)
 {
+	struct request *req = cmd->request;
 	unsigned long flags;
 
-	cmd->request->flags &= ~REQ_DONTPREP;
-
+	scsi_unprep_request(req);
 	spin_lock_irqsave(q->queue_lock, flags);
-	blk_requeue_request(q, cmd->request);
+	blk_requeue_request(q, req);
 	spin_unlock_irqrestore(q->queue_lock, flags);
 
 	scsi_run_queue(q);
@@ -595,13 +623,14 @@ void scsi_run_host_queues(struct Scsi_Host *shost)
  *
  * Lock status: Assumed that lock is not held upon entry.
  *
- * Returns:     cmd if requeue done or required, NULL otherwise
+ * Returns:     cmd if requeue required, NULL otherwise.
  *
  * Notes:       This is called for block device requests in order to
  *              mark some number of sectors as complete.
  * 
  *		We are guaranteeing that the request queue will be goosed
  *		at some point during this call.
+ * Notes:	If cmd was requeued, upon return it will be a stale pointer.
  */
 static struct scsi_cmnd *scsi_end_request(struct scsi_cmnd *cmd, int uptodate,
 					  int bytes, int requeue)
@@ -624,14 +653,15 @@ static struct scsi_cmnd *scsi_end_request(struct scsi_cmnd *cmd, int uptodate,
 		if (!uptodate && blk_noretry_request(req))
 			end_that_request_chunk(req, 0, leftover);
 		else {
-			if (requeue)
+			if (requeue) {
 				/*
 				 * Bleah.  Leftovers again.  Stick the
 				 * leftovers in the front of the
 				 * queue, and goose the queue again.
 				 */
 				scsi_requeue_command(q, cmd);
-
+				cmd = NULL;
+			}
 			return cmd;
 		}
 	}
@@ -857,15 +887,13 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes,
 		 * requeueing right here - we will requeue down below
 		 * when we handle the bad sectors.
 		 */
-		cmd = scsi_end_request(cmd, 1, good_bytes, result == 0);
 
 		/*
-		 * If the command completed without error, then either finish off the
-		 * rest of the command, or start a new one.
+		 * If the command completed without error, then either
+		 * finish off the rest of the command, or start a new one.
 		 */
-		if (result == 0 || cmd == NULL ) {
+		if (scsi_end_request(cmd, 1, good_bytes, result == 0) == NULL)
 			return;
-		}
 	}
 	/*
 	 * Now, if we were good little boys and girls, Santa left us a request
@@ -880,7 +908,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes,
 				 * and quietly refuse further access.
 				 */
 				cmd->device->changed = 1;
-				cmd = scsi_end_request(cmd, 0,
+				scsi_end_request(cmd, 0,
 						this_count, 1);
 				return;
 			} else {
@@ -914,7 +942,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes,
 				scsi_requeue_command(q, cmd);
 				result = 0;
 			} else {
-				cmd = scsi_end_request(cmd, 0, this_count, 1);
+				scsi_end_request(cmd, 0, this_count, 1);
 				return;
 			}
 			break;
@@ -931,7 +959,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes,
 				dev_printk(KERN_INFO,
 					   &cmd->device->sdev_gendev,
 					   "Device not ready.\n");
-			cmd = scsi_end_request(cmd, 0, this_count, 1);
+			scsi_end_request(cmd, 0, this_count, 1);
 			return;
 		case VOLUME_OVERFLOW:
 			if (!(req->flags & REQ_QUIET)) {
@@ -941,7 +969,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes,
 				__scsi_print_command(cmd->data_cmnd);
 				scsi_print_sense("", cmd);
 			}
-			cmd = scsi_end_request(cmd, 0, block_bytes, 1);
+			scsi_end_request(cmd, 0, block_bytes, 1);
 			return;
 		default:
 			break;
@@ -972,7 +1000,7 @@ void scsi_io_completion(struct scsi_cmnd *cmd, unsigned int good_bytes,
 		block_bytes = req->hard_cur_sectors << 9;
 		if (!block_bytes)
 			block_bytes = req->data_len;
-		cmd = scsi_end_request(cmd, 0, block_bytes, 1);
+		scsi_end_request(cmd, 0, block_bytes, 1);
 	}
 }
 EXPORT_SYMBOL(scsi_io_completion);
@@ -1118,7 +1146,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 	if (unlikely(!scsi_device_online(sdev))) {
 		printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to offline device\n",
 		       sdev->host->host_no, sdev->id, sdev->lun);
-		return BLKPREP_KILL;
+		goto kill;
 	}
 	if (unlikely(sdev->sdev_state != SDEV_RUNNING)) {
 		/* OK, we're not in a running state don't prep
@@ -1128,7 +1156,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 			 * at all allowed down */
 			printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to dead device\n",
 			       sdev->host->host_no, sdev->id, sdev->lun);
-			return BLKPREP_KILL;
+			goto kill;
 		}
 		/* OK, we only allow special commands (i.e. not
 		 * user initiated ones */
@@ -1160,11 +1188,11 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 		if(unlikely(specials_only) && !(req->flags & REQ_SPECIAL)) {
 			if(specials_only == SDEV_QUIESCE ||
 					specials_only == SDEV_BLOCK)
-				return BLKPREP_DEFER;
+				goto defer;
 			
 			printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to device being removed\n",
 			       sdev->host->host_no, sdev->id, sdev->lun);
-			return BLKPREP_KILL;
+			goto kill;
 		}
 			
 			
@@ -1182,7 +1210,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 		cmd->tag = req->tag;
 	} else {
 		blk_dump_rq_flags(req, "SCSI bad req");
-		return BLKPREP_KILL;
+		goto kill;
 	}
 	
 	/* note the overloading of req->special.  When the tag
@@ -1220,8 +1248,13 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 		 * required).
 		 */
 		ret = scsi_init_io(cmd);
-		if (ret)	/* BLKPREP_KILL return also releases the command */
-			return ret;
+		switch(ret) {
+		case BLKPREP_KILL:
+			/* BLKPREP_KILL return also releases the command */
+			goto kill;
+		case BLKPREP_DEFER:
+			goto defer;
+		}
 		
 		/*
 		 * Initialize the actual SCSI command for this request.
@@ -1231,7 +1264,7 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 			if (unlikely(!drv->init_command(cmd))) {
 				scsi_release_buffers(cmd);
 				scsi_put_command(cmd);
-				return BLKPREP_KILL;
+				goto kill;
 			}
 		} else {
 			memcpy(cmd->cmnd, req->cmd, sizeof(cmd->cmnd));
@@ -1262,6 +1295,9 @@ static int scsi_prep_fn(struct request_queue *q, struct request *req)
 	if (sdev->device_busy == 0)
 		blk_plug_device(q);
 	return BLKPREP_DEFER;
+ kill:
+	req->errors = DID_NO_CONNECT << 16;
+	return BLKPREP_KILL;
 }
 
 /*
@@ -1336,19 +1372,24 @@ static inline int scsi_host_queue_ready(struct request_queue *q,
 }
 
 /*
- * Kill requests for a dead device
+ * Kill a request for a dead device
  */
-static void scsi_kill_requests(request_queue_t *q)
+static void scsi_kill_request(struct request *req, request_queue_t *q)
 {
-	struct request *req;
+	struct scsi_cmnd *cmd = req->special;
+
+	blkdev_dequeue_request(req);
 
-	while ((req = elv_next_request(q)) != NULL) {
-		blkdev_dequeue_request(req);
-		req->flags |= REQ_QUIET;
-		while (end_that_request_first(req, 0, req->nr_sectors))
-			;
-		end_that_request_last(req);
+	if (unlikely(cmd == NULL)) {
+		printk(KERN_CRIT "impossible request in %s.\n",
+				 __FUNCTION__);
+		BUG();
 	}
+
+	scsi_init_cmd_errh(cmd);
+	cmd->result = DID_NO_CONNECT << 16;
+	atomic_inc(&cmd->device->iorequest_cnt);
+	__scsi_done(cmd);
 }
 
 /*
@@ -1371,7 +1412,8 @@ static void scsi_request_fn(struct request_queue *q)
 
 	if (!sdev) {
 		printk("scsi: killing requests for dead queue\n");
-		scsi_kill_requests(q);
+		while ((req = elv_next_request(q)) != NULL)
+			scsi_kill_request(req, q);
 		return;
 	}
 
@@ -1398,11 +1440,7 @@ static void scsi_request_fn(struct request_queue *q)
 		if (unlikely(!scsi_device_online(sdev))) {
 			printk(KERN_ERR "scsi%d (%d:%d): rejecting I/O to offline device\n",
 			       sdev->host->host_no, sdev->id, sdev->lun);
-			blkdev_dequeue_request(req);
-			req->flags |= REQ_QUIET;
-			while (end_that_request_first(req, 0, req->nr_sectors))
-				;
-			end_that_request_last(req);
+			scsi_kill_request(req, q);
 			continue;
 		}
 
@@ -1415,6 +1453,14 @@ static void scsi_request_fn(struct request_queue *q)
 		sdev->device_busy++;
 
 		spin_unlock(q->queue_lock);
+		cmd = req->special;
+		if (unlikely(cmd == NULL)) {
+			printk(KERN_CRIT "impossible request in %s.\n"
+					 "please mail a stack trace to "
+					 "linux-scsi@vger.kernel.org",
+					 __FUNCTION__);
+			BUG();
+		}
 		spin_lock(shost->host_lock);
 
 		if (!scsi_host_queue_ready(q, shost, sdev))
@@ -1433,15 +1479,6 @@ static void scsi_request_fn(struct request_queue *q)
 		 */
 		spin_unlock_irq(shost->host_lock);
 
-		cmd = req->special;
-		if (unlikely(cmd == NULL)) {
-			printk(KERN_CRIT "impossible request in %s.\n"
-					 "please mail a stack trace to "
-					 "linux-scsi@vger.kernel.org",
-					 __FUNCTION__);
-			BUG();
-		}
-
 		/*
 		 * Finally, initialize any error handling parameters, and set up
 		 * the timers for timeouts.
@@ -1477,6 +1514,7 @@ static void scsi_request_fn(struct request_queue *q)
 	 * cases (host limits or settings) should run the queue at some
 	 * later time.
 	 */
+	scsi_unprep_request(req);
 	spin_lock_irq(q->queue_lock);
 	blk_requeue_request(q, req);
 	sdev->device_busy--;
diff --git a/drivers/scsi/scsi_priv.h b/drivers/scsi/scsi_priv.h
index ee6de1768e5..d05f778d31a 100644
--- a/drivers/scsi/scsi_priv.h
+++ b/drivers/scsi/scsi_priv.h
@@ -124,6 +124,7 @@ extern void scsi_sysfs_unregister(void);
 extern void scsi_sysfs_device_initialize(struct scsi_device *);
 extern int scsi_sysfs_target_initialize(struct scsi_device *);
 extern struct scsi_transport_template blank_transport_template;
+extern void __scsi_remove_device(struct scsi_device *);
 
 extern struct bus_type scsi_bus_type;
 
diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c
index 19c9a232a75..b86f170fa8e 100644
--- a/drivers/scsi/scsi_scan.c
+++ b/drivers/scsi/scsi_scan.c
@@ -870,8 +870,12 @@ static int scsi_probe_and_add_lun(struct scsi_target *starget,
  out_free_sdev:
 	if (res == SCSI_SCAN_LUN_PRESENT) {
 		if (sdevp) {
-			scsi_device_get(sdev);
-			*sdevp = sdev;
+			if (scsi_device_get(sdev) == 0) {
+				*sdevp = sdev;
+			} else {
+				__scsi_remove_device(sdev);
+				res = SCSI_SCAN_NO_RESPONSE;
+			}
 		}
 	} else {
 		if (sdev->host->hostt->slave_destroy)
@@ -1260,6 +1264,19 @@ struct scsi_device *__scsi_add_device(struct Scsi_Host *shost, uint channel,
 }
 EXPORT_SYMBOL(__scsi_add_device);
 
+int scsi_add_device(struct Scsi_Host *host, uint channel,
+		    uint target, uint lun)
+{
+	struct scsi_device *sdev = 
+		__scsi_add_device(host, channel, target, lun, NULL);
+	if (IS_ERR(sdev))
+		return PTR_ERR(sdev);
+
+	scsi_device_put(sdev);
+	return 0;
+}
+EXPORT_SYMBOL(scsi_add_device);
+
 void scsi_rescan_device(struct device *dev)
 {
 	struct scsi_driver *drv;
@@ -1276,27 +1293,8 @@ void scsi_rescan_device(struct device *dev)
 }
 EXPORT_SYMBOL(scsi_rescan_device);
 
-/**
- * scsi_scan_target - scan a target id, possibly including all LUNs on the
- *     target.
- * @sdevsca:	Scsi_Device handle for scanning
- * @shost:	host to scan
- * @channel:	channel to scan
- * @id:		target id to scan
- *
- * Description:
- *     Scan the target id on @shost, @channel, and @id. Scan at least LUN
- *     0, and possibly all LUNs on the target id.
- *
- *     Use the pre-allocated @sdevscan as a handle for the scanning. This
- *     function sets sdevscan->host, sdevscan->id and sdevscan->lun; the
- *     scanning functions modify sdevscan->lun.
- *
- *     First try a REPORT LUN scan, if that does not scan the target, do a
- *     sequential scan of LUNs on the target id.
- **/
-void scsi_scan_target(struct device *parent, unsigned int channel,
-		      unsigned int id, unsigned int lun, int rescan)
+static void __scsi_scan_target(struct device *parent, unsigned int channel,
+		unsigned int id, unsigned int lun, int rescan)
 {
 	struct Scsi_Host *shost = dev_to_shost(parent);
 	int bflags = 0;
@@ -1310,9 +1308,7 @@ void scsi_scan_target(struct device *parent, unsigned int channel,
 		 */
 		return;
 
-
 	starget = scsi_alloc_target(parent, channel, id);
-
 	if (!starget)
 		return;
 
@@ -1358,6 +1354,33 @@ void scsi_scan_target(struct device *parent, unsigned int channel,
 
 	put_device(&starget->dev);
 }
+
+/**
+ * scsi_scan_target - scan a target id, possibly including all LUNs on the
+ *     target.
+ * @parent:	host to scan
+ * @channel:	channel to scan
+ * @id:		target id to scan
+ * @lun:	Specific LUN to scan or SCAN_WILD_CARD
+ * @rescan:	passed to LUN scanning routines
+ *
+ * Description:
+ *     Scan the target id on @parent, @channel, and @id. Scan at least LUN 0,
+ *     and possibly all LUNs on the target id.
+ *
+ *     First try a REPORT LUN scan, if that does not scan the target, do a
+ *     sequential scan of LUNs on the target id.
+ **/
+void scsi_scan_target(struct device *parent, unsigned int channel,
+		      unsigned int id, unsigned int lun, int rescan)
+{
+	struct Scsi_Host *shost = dev_to_shost(parent);
+
+	down(&shost->scan_mutex);
+	if (scsi_host_scan_allowed(shost))
+		__scsi_scan_target(parent, channel, id, lun, rescan);
+	up(&shost->scan_mutex);
+}
 EXPORT_SYMBOL(scsi_scan_target);
 
 static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel,
@@ -1383,10 +1406,12 @@ static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel,
 				order_id = shost->max_id - id - 1;
 			else
 				order_id = id;
-			scsi_scan_target(&shost->shost_gendev, channel, order_id, lun, rescan);
+			__scsi_scan_target(&shost->shost_gendev, channel,
+					order_id, lun, rescan);
 		}
 	else
-		scsi_scan_target(&shost->shost_gendev, channel, id, lun, rescan);
+		__scsi_scan_target(&shost->shost_gendev, channel,
+				id, lun, rescan);
 }
 
 int scsi_scan_host_selected(struct Scsi_Host *shost, unsigned int channel,
@@ -1484,12 +1509,15 @@ void scsi_forget_host(struct Scsi_Host *shost)
  */
 struct scsi_device *scsi_get_host_dev(struct Scsi_Host *shost)
 {
-	struct scsi_device *sdev;
+	struct scsi_device *sdev = NULL;
 	struct scsi_target *starget;
 
+	down(&shost->scan_mutex);
+	if (!scsi_host_scan_allowed(shost))
+		goto out;
 	starget = scsi_alloc_target(&shost->shost_gendev, 0, shost->this_id);
 	if (!starget)
-		return NULL;
+		goto out;
 
 	sdev = scsi_alloc_sdev(starget, 0, NULL);
 	if (sdev) {
@@ -1497,6 +1525,8 @@ struct scsi_device *scsi_get_host_dev(struct Scsi_Host *shost)
 		sdev->borken = 0;
 	}
 	put_device(&starget->dev);
+ out:
+	up(&shost->scan_mutex);
 	return sdev;
 }
 EXPORT_SYMBOL(scsi_get_host_dev);
diff --git a/drivers/scsi/scsi_sysfs.c b/drivers/scsi/scsi_sysfs.c
index dae59d1da07..b8052d5206c 100644
--- a/drivers/scsi/scsi_sysfs.c
+++ b/drivers/scsi/scsi_sysfs.c
@@ -653,7 +653,7 @@ int scsi_sysfs_add_sdev(struct scsi_device *sdev)
 			error = attr_add(&sdev->sdev_gendev,
 					sdev->host->hostt->sdev_attrs[i]);
 			if (error) {
-				scsi_remove_device(sdev);
+				__scsi_remove_device(sdev);
 				goto out;
 			}
 		}
@@ -667,7 +667,7 @@ int scsi_sysfs_add_sdev(struct scsi_device *sdev)
 							scsi_sysfs_sdev_attrs[i]);
 			error = device_create_file(&sdev->sdev_gendev, attr);
 			if (error) {
-				scsi_remove_device(sdev);
+				__scsi_remove_device(sdev);
 				goto out;
 			}
 		}
@@ -687,17 +687,10 @@ int scsi_sysfs_add_sdev(struct scsi_device *sdev)
 	return error;
 }
 
-/**
- * scsi_remove_device - unregister a device from the scsi bus
- * @sdev:	scsi_device to unregister
- **/
-void scsi_remove_device(struct scsi_device *sdev)
+void __scsi_remove_device(struct scsi_device *sdev)
 {
-	struct Scsi_Host *shost = sdev->host;
-
-	down(&shost->scan_mutex);
 	if (scsi_device_set_state(sdev, SDEV_CANCEL) != 0)
-		goto out;
+		return;
 
 	class_device_unregister(&sdev->sdev_classdev);
 	device_del(&sdev->sdev_gendev);
@@ -706,8 +699,17 @@ void scsi_remove_device(struct scsi_device *sdev)
 		sdev->host->hostt->slave_destroy(sdev);
 	transport_unregister_device(&sdev->sdev_gendev);
 	put_device(&sdev->sdev_gendev);
-out:
-	up(&shost->scan_mutex);
+}
+
+/**
+ * scsi_remove_device - unregister a device from the scsi bus
+ * @sdev:	scsi_device to unregister
+ **/
+void scsi_remove_device(struct scsi_device *sdev)
+{
+	down(&sdev->host->scan_mutex);
+	__scsi_remove_device(sdev);
+	up(&sdev->host->scan_mutex);
 }
 EXPORT_SYMBOL(scsi_remove_device);
 
diff --git a/drivers/scsi/scsi_transport_sas.c b/drivers/scsi/scsi_transport_sas.c
new file mode 100644
index 00000000000..ff724bbe661
--- /dev/null
+++ b/drivers/scsi/scsi_transport_sas.c
@@ -0,0 +1,820 @@
+/*
+ * Copyright (C) 2005 Dell Inc.
+ *	Released under GPL v2.
+ *
+ * Serial Attached SCSI (SAS) transport class.
+ *
+ * The SAS transport class contains common code to deal with SAS HBAs,
+ * an aproximated representation of SAS topologies in the driver model,
+ * and various sysfs attributes to expose these topologies and managment
+ * interfaces to userspace.
+ *
+ * In addition to the basic SCSI core objects this transport class
+ * introduces two additional intermediate objects:  The SAS PHY
+ * as represented by struct sas_phy defines an "outgoing" PHY on
+ * a SAS HBA or Expander, and the SAS remote PHY represented by
+ * struct sas_rphy defines an "incoming" PHY on a SAS Expander or
+ * end device.  Note that this is purely a software concept, the
+ * underlying hardware for a PHY and a remote PHY is the exactly
+ * the same.
+ *
+ * There is no concept of a SAS port in this code, users can see
+ * what PHYs form a wide port based on the port_identifier attribute,
+ * which is the same for all PHYs in a port.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/err.h>
+
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_transport.h>
+#include <scsi/scsi_transport_sas.h>
+
+
+#define SAS_HOST_ATTRS		0
+#define SAS_PORT_ATTRS		11
+#define SAS_RPORT_ATTRS		5
+
+struct sas_internal {
+	struct scsi_transport_template t;
+	struct sas_function_template *f;
+
+	struct class_device_attribute private_host_attrs[SAS_HOST_ATTRS];
+	struct class_device_attribute private_phy_attrs[SAS_PORT_ATTRS];
+	struct class_device_attribute private_rphy_attrs[SAS_RPORT_ATTRS];
+
+	struct transport_container phy_attr_cont;
+	struct transport_container rphy_attr_cont;
+
+	/*
+	 * The array of null terminated pointers to attributes
+	 * needed by scsi_sysfs.c
+	 */
+	struct class_device_attribute *host_attrs[SAS_HOST_ATTRS + 1];
+	struct class_device_attribute *phy_attrs[SAS_PORT_ATTRS + 1];
+	struct class_device_attribute *rphy_attrs[SAS_RPORT_ATTRS + 1];
+};
+#define to_sas_internal(tmpl)	container_of(tmpl, struct sas_internal, t)
+
+struct sas_host_attrs {
+	struct list_head rphy_list;
+	spinlock_t lock;
+	u32 next_target_id;
+};
+#define to_sas_host_attrs(host)	((struct sas_host_attrs *)(host)->shost_data)
+
+
+/*
+ * Hack to allow attributes of the same name in different objects.
+ */
+#define SAS_CLASS_DEVICE_ATTR(_prefix,_name,_mode,_show,_store) \
+	struct class_device_attribute class_device_attr_##_prefix##_##_name = \
+	__ATTR(_name,_mode,_show,_store)
+
+
+/*
+ * Pretty printing helpers
+ */
+
+#define sas_bitfield_name_match(title, table)			\
+static ssize_t							\
+get_sas_##title##_names(u32 table_key, char *buf)		\
+{								\
+	char *prefix = "";					\
+	ssize_t len = 0;					\
+	int i;							\
+								\
+	for (i = 0; i < sizeof(table)/sizeof(table[0]); i++) {	\
+		if (table[i].value & table_key) {		\
+			len += sprintf(buf + len, "%s%s",	\
+				prefix, table[i].name);		\
+			prefix = ", ";				\
+		}						\
+	}							\
+	len += sprintf(buf + len, "\n");			\
+	return len;						\
+}
+
+#define sas_bitfield_name_search(title, table)			\
+static ssize_t							\
+get_sas_##title##_names(u32 table_key, char *buf)		\
+{								\
+	ssize_t len = 0;					\
+	int i;							\
+								\
+	for (i = 0; i < sizeof(table)/sizeof(table[0]); i++) {	\
+		if (table[i].value == table_key) {		\
+			len += sprintf(buf + len, "%s",		\
+				table[i].name);			\
+			break;					\
+		}						\
+	}							\
+	len += sprintf(buf + len, "\n");			\
+	return len;						\
+}
+
+static struct {
+	u32		value;
+	char		*name;
+} sas_device_type_names[] = {
+	{ SAS_PHY_UNUSED,		"unused" },
+	{ SAS_END_DEVICE,		"end device" },
+	{ SAS_EDGE_EXPANDER_DEVICE,	"edge expander" },
+	{ SAS_FANOUT_EXPANDER_DEVICE,	"fanout expander" },
+};
+sas_bitfield_name_search(device_type, sas_device_type_names)
+
+
+static struct {
+	u32		value;
+	char		*name;
+} sas_protocol_names[] = {
+	{ SAS_PROTOCOL_SATA,		"sata" },
+	{ SAS_PROTOCOL_SMP,		"smp" },
+	{ SAS_PROTOCOL_STP,		"stp" },
+	{ SAS_PROTOCOL_SSP,		"ssp" },
+};
+sas_bitfield_name_match(protocol, sas_protocol_names)
+
+static struct {
+	u32		value;
+	char		*name;
+} sas_linkspeed_names[] = {
+	{ SAS_LINK_RATE_UNKNOWN,	"Unknown" },
+	{ SAS_PHY_DISABLED,		"Phy disabled" },
+	{ SAS_LINK_RATE_FAILED,		"Link Rate failed" },
+	{ SAS_SATA_SPINUP_HOLD,		"Spin-up hold" },
+	{ SAS_LINK_RATE_1_5_GBPS,	"1.5 Gbit" },
+	{ SAS_LINK_RATE_3_0_GBPS,	"3.0 Gbit" },
+};
+sas_bitfield_name_search(linkspeed, sas_linkspeed_names)
+
+
+/*
+ * SAS host attributes
+ */
+
+static int sas_host_setup(struct transport_container *tc, struct device *dev,
+			  struct class_device *cdev)
+{
+	struct Scsi_Host *shost = dev_to_shost(dev);
+	struct sas_host_attrs *sas_host = to_sas_host_attrs(shost);
+
+	INIT_LIST_HEAD(&sas_host->rphy_list);
+	spin_lock_init(&sas_host->lock);
+	sas_host->next_target_id = 0;
+	return 0;
+}
+
+static DECLARE_TRANSPORT_CLASS(sas_host_class,
+		"sas_host", sas_host_setup, NULL, NULL);
+
+static int sas_host_match(struct attribute_container *cont,
+			    struct device *dev)
+{
+	struct Scsi_Host *shost;
+	struct sas_internal *i;
+
+	if (!scsi_is_host_device(dev))
+		return 0;
+	shost = dev_to_shost(dev);
+
+	if (!shost->transportt)
+		return 0;
+	if (shost->transportt->host_attrs.ac.class !=
+			&sas_host_class.class)
+		return 0;
+
+	i = to_sas_internal(shost->transportt);
+	return &i->t.host_attrs.ac == cont;
+}
+
+static int do_sas_phy_delete(struct device *dev, void *data)
+{
+	if (scsi_is_sas_phy(dev))
+		sas_phy_delete(dev_to_phy(dev));
+	return 0;
+}
+
+/**
+ * sas_remove_host  --  tear down a Scsi_Host's SAS data structures
+ * @shost:	Scsi Host that is torn down
+ *
+ * Removes all SAS PHYs and remote PHYs for a given Scsi_Host.
+ * Must be called just before scsi_remove_host for SAS HBAs.
+ */
+void sas_remove_host(struct Scsi_Host *shost)
+{
+	device_for_each_child(&shost->shost_gendev, NULL, do_sas_phy_delete);
+}
+EXPORT_SYMBOL(sas_remove_host);
+
+
+/*
+ * SAS Port attributes
+ */
+
+#define sas_phy_show_simple(field, name, format_string, cast)		\
+static ssize_t								\
+show_sas_phy_##name(struct class_device *cdev, char *buf)		\
+{									\
+	struct sas_phy *phy = transport_class_to_phy(cdev);		\
+									\
+	return snprintf(buf, 20, format_string, cast phy->field);	\
+}
+
+#define sas_phy_simple_attr(field, name, format_string, type)		\
+	sas_phy_show_simple(field, name, format_string, (type))	\
+static CLASS_DEVICE_ATTR(name, S_IRUGO, show_sas_phy_##name, NULL)
+
+#define sas_phy_show_protocol(field, name)				\
+static ssize_t								\
+show_sas_phy_##name(struct class_device *cdev, char *buf)		\
+{									\
+	struct sas_phy *phy = transport_class_to_phy(cdev);		\
+									\
+	if (!phy->field)						\
+		return snprintf(buf, 20, "none\n");			\
+	return get_sas_protocol_names(phy->field, buf);		\
+}
+
+#define sas_phy_protocol_attr(field, name)				\
+	sas_phy_show_protocol(field, name)				\
+static CLASS_DEVICE_ATTR(name, S_IRUGO, show_sas_phy_##name, NULL)
+
+#define sas_phy_show_linkspeed(field)					\
+static ssize_t								\
+show_sas_phy_##field(struct class_device *cdev, char *buf)		\
+{									\
+	struct sas_phy *phy = transport_class_to_phy(cdev);		\
+									\
+	return get_sas_linkspeed_names(phy->field, buf);		\
+}
+
+#define sas_phy_linkspeed_attr(field)					\
+	sas_phy_show_linkspeed(field)					\
+static CLASS_DEVICE_ATTR(field, S_IRUGO, show_sas_phy_##field, NULL)
+
+static ssize_t
+show_sas_device_type(struct class_device *cdev, char *buf)
+{
+	struct sas_phy *phy = transport_class_to_phy(cdev);
+
+	if (!phy->identify.device_type)
+		return snprintf(buf, 20, "none\n");
+	return get_sas_device_type_names(phy->identify.device_type, buf);
+}
+
+static CLASS_DEVICE_ATTR(device_type, S_IRUGO, show_sas_device_type, NULL);
+
+sas_phy_protocol_attr(identify.initiator_port_protocols,
+		initiator_port_protocols);
+sas_phy_protocol_attr(identify.target_port_protocols,
+		target_port_protocols);
+sas_phy_simple_attr(identify.sas_address, sas_address, "0x%016llx\n",
+		unsigned long long);
+sas_phy_simple_attr(identify.phy_identifier, phy_identifier, "%d\n", u8);
+sas_phy_simple_attr(port_identifier, port_identifier, "%d\n", u8);
+sas_phy_linkspeed_attr(negotiated_linkrate);
+sas_phy_linkspeed_attr(minimum_linkrate_hw);
+sas_phy_linkspeed_attr(minimum_linkrate);
+sas_phy_linkspeed_attr(maximum_linkrate_hw);
+sas_phy_linkspeed_attr(maximum_linkrate);
+
+
+static DECLARE_TRANSPORT_CLASS(sas_phy_class,
+		"sas_phy", NULL, NULL, NULL);
+
+static int sas_phy_match(struct attribute_container *cont, struct device *dev)
+{
+	struct Scsi_Host *shost;
+	struct sas_internal *i;
+
+	if (!scsi_is_sas_phy(dev))
+		return 0;
+	shost = dev_to_shost(dev->parent);
+
+	if (!shost->transportt)
+		return 0;
+	if (shost->transportt->host_attrs.ac.class !=
+			&sas_host_class.class)
+		return 0;
+
+	i = to_sas_internal(shost->transportt);
+	return &i->phy_attr_cont.ac == cont;
+}
+
+static void sas_phy_release(struct device *dev)
+{
+	struct sas_phy *phy = dev_to_phy(dev);
+
+	put_device(dev->parent);
+	kfree(phy);
+}
+
+/**
+ * sas_phy_alloc  --  allocates and initialize a SAS PHY structure
+ * @parent:	Parent device
+ * @number:	Port number
+ *
+ * Allocates an SAS PHY structure.  It will be added in the device tree
+ * below the device specified by @parent, which has to be either a Scsi_Host
+ * or sas_rphy.
+ *
+ * Returns:
+ *	SAS PHY allocated or %NULL if the allocation failed.
+ */
+struct sas_phy *sas_phy_alloc(struct device *parent, int number)
+{
+	struct Scsi_Host *shost = dev_to_shost(parent);
+	struct sas_phy *phy;
+
+	phy = kmalloc(sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return NULL;
+	memset(phy, 0, sizeof(*phy));
+
+	get_device(parent);
+
+	phy->number = number;
+
+	device_initialize(&phy->dev);
+	phy->dev.parent = get_device(parent);
+	phy->dev.release = sas_phy_release;
+	sprintf(phy->dev.bus_id, "phy-%d:%d", shost->host_no, number);
+
+	transport_setup_device(&phy->dev);
+
+	return phy;
+}
+EXPORT_SYMBOL(sas_phy_alloc);
+
+/**
+ * sas_phy_add  --  add a SAS PHY to the device hierachy
+ * @phy:	The PHY to be added
+ *
+ * Publishes a SAS PHY to the rest of the system.
+ */
+int sas_phy_add(struct sas_phy *phy)
+{
+	int error;
+
+	error = device_add(&phy->dev);
+	if (!error) {
+		transport_add_device(&phy->dev);
+		transport_configure_device(&phy->dev);
+	}
+
+	return error;
+}
+EXPORT_SYMBOL(sas_phy_add);
+
+/**
+ * sas_phy_free  --  free a SAS PHY
+ * @phy:	SAS PHY to free
+ *
+ * Frees the specified SAS PHY.
+ *
+ * Note:
+ *   This function must only be called on a PHY that has not
+ *   sucessfully been added using sas_phy_add().
+ */
+void sas_phy_free(struct sas_phy *phy)
+{
+	transport_destroy_device(&phy->dev);
+	put_device(phy->dev.parent);
+	put_device(phy->dev.parent);
+	put_device(phy->dev.parent);
+	kfree(phy);
+}
+EXPORT_SYMBOL(sas_phy_free);
+
+/**
+ * sas_phy_delete  --  remove SAS PHY
+ * @phy:	SAS PHY to remove
+ *
+ * Removes the specified SAS PHY.  If the SAS PHY has an
+ * associated remote PHY it is removed before.
+ */
+void
+sas_phy_delete(struct sas_phy *phy)
+{
+	struct device *dev = &phy->dev;
+
+	if (phy->rphy)
+		sas_rphy_delete(phy->rphy);
+
+	transport_remove_device(dev);
+	device_del(dev);
+	transport_destroy_device(dev);
+	put_device(dev->parent);
+}
+EXPORT_SYMBOL(sas_phy_delete);
+
+/**
+ * scsi_is_sas_phy  --  check if a struct device represents a SAS PHY
+ * @dev:	device to check
+ *
+ * Returns:
+ *	%1 if the device represents a SAS PHY, %0 else
+ */
+int scsi_is_sas_phy(const struct device *dev)
+{
+	return dev->release == sas_phy_release;
+}
+EXPORT_SYMBOL(scsi_is_sas_phy);
+
+/*
+ * SAS remote PHY attributes.
+ */
+
+#define sas_rphy_show_simple(field, name, format_string, cast)		\
+static ssize_t								\
+show_sas_rphy_##name(struct class_device *cdev, char *buf)		\
+{									\
+	struct sas_rphy *rphy = transport_class_to_rphy(cdev);	\
+									\
+	return snprintf(buf, 20, format_string, cast rphy->field);	\
+}
+
+#define sas_rphy_simple_attr(field, name, format_string, type)		\
+	sas_rphy_show_simple(field, name, format_string, (type))	\
+static SAS_CLASS_DEVICE_ATTR(rphy, name, S_IRUGO, 			\
+		show_sas_rphy_##name, NULL)
+
+#define sas_rphy_show_protocol(field, name)				\
+static ssize_t								\
+show_sas_rphy_##name(struct class_device *cdev, char *buf)		\
+{									\
+	struct sas_rphy *rphy = transport_class_to_rphy(cdev);	\
+									\
+	if (!rphy->field)					\
+		return snprintf(buf, 20, "none\n");			\
+	return get_sas_protocol_names(rphy->field, buf);	\
+}
+
+#define sas_rphy_protocol_attr(field, name)				\
+	sas_rphy_show_protocol(field, name)				\
+static SAS_CLASS_DEVICE_ATTR(rphy, name, S_IRUGO,			\
+		show_sas_rphy_##name, NULL)
+
+static ssize_t
+show_sas_rphy_device_type(struct class_device *cdev, char *buf)
+{
+	struct sas_rphy *rphy = transport_class_to_rphy(cdev);
+
+	if (!rphy->identify.device_type)
+		return snprintf(buf, 20, "none\n");
+	return get_sas_device_type_names(
+			rphy->identify.device_type, buf);
+}
+
+static SAS_CLASS_DEVICE_ATTR(rphy, device_type, S_IRUGO,
+		show_sas_rphy_device_type, NULL);
+
+sas_rphy_protocol_attr(identify.initiator_port_protocols,
+		initiator_port_protocols);
+sas_rphy_protocol_attr(identify.target_port_protocols, target_port_protocols);
+sas_rphy_simple_attr(identify.sas_address, sas_address, "0x%016llx\n",
+		unsigned long long);
+sas_rphy_simple_attr(identify.phy_identifier, phy_identifier, "%d\n", u8);
+
+static DECLARE_TRANSPORT_CLASS(sas_rphy_class,
+		"sas_rphy", NULL, NULL, NULL);
+
+static int sas_rphy_match(struct attribute_container *cont, struct device *dev)
+{
+	struct Scsi_Host *shost;
+	struct sas_internal *i;
+
+	if (!scsi_is_sas_rphy(dev))
+		return 0;
+	shost = dev_to_shost(dev->parent->parent);
+
+	if (!shost->transportt)
+		return 0;
+	if (shost->transportt->host_attrs.ac.class !=
+			&sas_host_class.class)
+		return 0;
+
+	i = to_sas_internal(shost->transportt);
+	return &i->rphy_attr_cont.ac == cont;
+}
+
+static void sas_rphy_release(struct device *dev)
+{
+	struct sas_rphy *rphy = dev_to_rphy(dev);
+
+	put_device(dev->parent);
+	kfree(rphy);
+}
+
+/**
+ * sas_rphy_alloc  --  allocates and initialize a SAS remote PHY structure
+ * @parent:		SAS PHY this remote PHY is conneted to
+ *
+ * Allocates an SAS remote PHY structure, connected to @parent.
+ *
+ * Returns:
+ *	SAS PHY allocated or %NULL if the allocation failed.
+ */
+struct sas_rphy *sas_rphy_alloc(struct sas_phy *parent)
+{
+	struct Scsi_Host *shost = dev_to_shost(&parent->dev);
+	struct sas_rphy *rphy;
+
+	rphy = kmalloc(sizeof(*rphy), GFP_KERNEL);
+	if (!rphy) {
+		put_device(&parent->dev);
+		return NULL;
+	}
+	memset(rphy, 0, sizeof(*rphy));
+
+	device_initialize(&rphy->dev);
+	rphy->dev.parent = get_device(&parent->dev);
+	rphy->dev.release = sas_rphy_release;
+	sprintf(rphy->dev.bus_id, "rphy-%d:%d",
+		shost->host_no, parent->number);
+	transport_setup_device(&rphy->dev);
+
+	return rphy;
+}
+EXPORT_SYMBOL(sas_rphy_alloc);
+
+/**
+ * sas_rphy_add  --  add a SAS remote PHY to the device hierachy
+ * @rphy:	The remote PHY to be added
+ *
+ * Publishes a SAS remote PHY to the rest of the system.
+ */
+int sas_rphy_add(struct sas_rphy *rphy)
+{
+	struct sas_phy *parent = dev_to_phy(rphy->dev.parent);
+	struct Scsi_Host *shost = dev_to_shost(parent->dev.parent);
+	struct sas_host_attrs *sas_host = to_sas_host_attrs(shost);
+	struct sas_identify *identify = &rphy->identify;
+	int error;
+
+	if (parent->rphy)
+		return -ENXIO;
+	parent->rphy = rphy;
+
+	error = device_add(&rphy->dev);
+	if (error)
+		return error;
+	transport_add_device(&rphy->dev);
+	transport_configure_device(&rphy->dev);
+
+	spin_lock(&sas_host->lock);
+	list_add_tail(&rphy->list, &sas_host->rphy_list);
+	if (identify->device_type == SAS_END_DEVICE &&
+	    (identify->target_port_protocols &
+	     (SAS_PROTOCOL_SSP|SAS_PROTOCOL_STP|SAS_PROTOCOL_SATA)))
+		rphy->scsi_target_id = sas_host->next_target_id++;
+	else
+		rphy->scsi_target_id = -1;
+	spin_unlock(&sas_host->lock);
+
+	if (rphy->scsi_target_id != -1) {
+		scsi_scan_target(&rphy->dev, parent->number,
+				rphy->scsi_target_id, ~0, 0);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(sas_rphy_add);
+
+/**
+ * sas_rphy_free  --  free a SAS remote PHY
+ * @rphy	SAS remote PHY to free
+ *
+ * Frees the specified SAS remote PHY.
+ *
+ * Note:
+ *   This function must only be called on a remote
+ *   PHY that has not sucessfully been added using
+ *   sas_rphy_add().
+ */
+void sas_rphy_free(struct sas_rphy *rphy)
+{
+	struct Scsi_Host *shost = dev_to_shost(rphy->dev.parent->parent);
+	struct sas_host_attrs *sas_host = to_sas_host_attrs(shost);
+
+	spin_lock(&sas_host->lock);
+	list_del(&rphy->list);
+	spin_unlock(&sas_host->lock);
+
+	transport_destroy_device(&rphy->dev);
+	put_device(rphy->dev.parent);
+	put_device(rphy->dev.parent);
+	put_device(rphy->dev.parent);
+	kfree(rphy);
+}
+EXPORT_SYMBOL(sas_rphy_free);
+
+/**
+ * sas_rphy_delete  --  remove SAS remote PHY
+ * @rphy:	SAS remote PHY to remove
+ *
+ * Removes the specified SAS remote PHY.
+ */
+void
+sas_rphy_delete(struct sas_rphy *rphy)
+{
+	struct device *dev = &rphy->dev;
+	struct sas_phy *parent = dev_to_phy(dev->parent);
+	struct Scsi_Host *shost = dev_to_shost(parent->dev.parent);
+	struct sas_host_attrs *sas_host = to_sas_host_attrs(shost);
+
+	transport_destroy_device(&rphy->dev);
+
+	scsi_remove_target(&rphy->dev);
+
+	spin_lock(&sas_host->lock);
+	list_del(&rphy->list);
+	spin_unlock(&sas_host->lock);
+
+	transport_remove_device(dev);
+	device_del(dev);
+	transport_destroy_device(dev);
+	put_device(&parent->dev);
+}
+EXPORT_SYMBOL(sas_rphy_delete);
+
+/**
+ * scsi_is_sas_rphy  --  check if a struct device represents a SAS remote PHY
+ * @dev:	device to check
+ *
+ * Returns:
+ *	%1 if the device represents a SAS remote PHY, %0 else
+ */
+int scsi_is_sas_rphy(const struct device *dev)
+{
+	return dev->release == sas_rphy_release;
+}
+EXPORT_SYMBOL(scsi_is_sas_rphy);
+
+
+/*
+ * SCSI scan helper
+ */
+
+static struct device *sas_target_parent(struct Scsi_Host *shost,
+					int channel, uint id)
+{
+	struct sas_host_attrs *sas_host = to_sas_host_attrs(shost);
+	struct sas_rphy *rphy;
+	struct device *dev = NULL;
+
+	spin_lock(&sas_host->lock);
+	list_for_each_entry(rphy, &sas_host->rphy_list, list) {
+		struct sas_phy *parent = dev_to_phy(rphy->dev.parent);
+		if (parent->number == channel &&
+		    rphy->scsi_target_id == id)
+			dev = &rphy->dev;
+	}
+	spin_unlock(&sas_host->lock);
+
+	return dev;
+}
+
+
+/*
+ * Setup / Teardown code
+ */
+
+#define SETUP_RPORT_ATTRIBUTE(field)					\
+	i->private_rphy_attrs[count] = class_device_attr_##field;	\
+	i->private_rphy_attrs[count].attr.mode = S_IRUGO;		\
+	i->private_rphy_attrs[count].store = NULL;			\
+	i->rphy_attrs[count] = &i->private_rphy_attrs[count];	\
+	count++
+
+#define SETUP_PORT_ATTRIBUTE(field)					\
+	i->private_phy_attrs[count] = class_device_attr_##field;	\
+        i->private_phy_attrs[count].attr.mode = S_IRUGO;		\
+        i->private_phy_attrs[count].store = NULL;			\
+        i->phy_attrs[count] = &i->private_phy_attrs[count];		\
+	count++
+
+
+/**
+ * sas_attach_transport  --  instantiate SAS transport template
+ * @ft:		SAS transport class function template
+ */
+struct scsi_transport_template *
+sas_attach_transport(struct sas_function_template *ft)
+{
+	struct sas_internal *i;
+	int count;
+
+	i = kmalloc(sizeof(struct sas_internal), GFP_KERNEL);
+	if (!i)
+		return NULL;
+	memset(i, 0, sizeof(struct sas_internal));
+
+	i->t.target_parent = sas_target_parent;
+
+	i->t.host_attrs.ac.attrs = &i->host_attrs[0];
+	i->t.host_attrs.ac.class = &sas_host_class.class;
+	i->t.host_attrs.ac.match = sas_host_match;
+	transport_container_register(&i->t.host_attrs);
+	i->t.host_size = sizeof(struct sas_host_attrs);
+
+	i->phy_attr_cont.ac.class = &sas_phy_class.class;
+	i->phy_attr_cont.ac.attrs = &i->phy_attrs[0];
+	i->phy_attr_cont.ac.match = sas_phy_match;
+	transport_container_register(&i->phy_attr_cont);
+
+	i->rphy_attr_cont.ac.class = &sas_rphy_class.class;
+	i->rphy_attr_cont.ac.attrs = &i->rphy_attrs[0];
+	i->rphy_attr_cont.ac.match = sas_rphy_match;
+	transport_container_register(&i->rphy_attr_cont);
+
+	i->f = ft;
+
+	count = 0;
+	i->host_attrs[count] = NULL;
+
+	count = 0;
+	SETUP_PORT_ATTRIBUTE(initiator_port_protocols);
+	SETUP_PORT_ATTRIBUTE(target_port_protocols);
+	SETUP_PORT_ATTRIBUTE(device_type);
+	SETUP_PORT_ATTRIBUTE(sas_address);
+	SETUP_PORT_ATTRIBUTE(phy_identifier);
+	SETUP_PORT_ATTRIBUTE(port_identifier);
+	SETUP_PORT_ATTRIBUTE(negotiated_linkrate);
+	SETUP_PORT_ATTRIBUTE(minimum_linkrate_hw);
+	SETUP_PORT_ATTRIBUTE(minimum_linkrate);
+	SETUP_PORT_ATTRIBUTE(maximum_linkrate_hw);
+	SETUP_PORT_ATTRIBUTE(maximum_linkrate);
+	i->phy_attrs[count] = NULL;
+
+	count = 0;
+	SETUP_RPORT_ATTRIBUTE(rphy_initiator_port_protocols);
+	SETUP_RPORT_ATTRIBUTE(rphy_target_port_protocols);
+	SETUP_RPORT_ATTRIBUTE(rphy_device_type);
+	SETUP_RPORT_ATTRIBUTE(rphy_sas_address);
+	SETUP_RPORT_ATTRIBUTE(rphy_phy_identifier);
+	i->rphy_attrs[count] = NULL;
+
+	return &i->t;
+}
+EXPORT_SYMBOL(sas_attach_transport);
+
+/**
+ * sas_release_transport  --  release SAS transport template instance
+ * @t:		transport template instance
+ */
+void sas_release_transport(struct scsi_transport_template *t)
+{
+	struct sas_internal *i = to_sas_internal(t);
+
+	transport_container_unregister(&i->t.host_attrs);
+	transport_container_unregister(&i->phy_attr_cont);
+	transport_container_unregister(&i->rphy_attr_cont);
+
+	kfree(i);
+}
+EXPORT_SYMBOL(sas_release_transport);
+
+static __init int sas_transport_init(void)
+{
+	int error;
+
+	error = transport_class_register(&sas_host_class);
+	if (error)
+		goto out;
+	error = transport_class_register(&sas_phy_class);
+	if (error)
+		goto out_unregister_transport;
+	error = transport_class_register(&sas_rphy_class);
+	if (error)
+		goto out_unregister_phy;
+
+	return 0;
+
+ out_unregister_phy:
+	transport_class_unregister(&sas_phy_class);
+ out_unregister_transport:
+	transport_class_unregister(&sas_host_class);
+ out:
+	return error;
+
+}
+
+static void __exit sas_transport_exit(void)
+{
+	transport_class_unregister(&sas_host_class);
+	transport_class_unregister(&sas_phy_class);
+	transport_class_unregister(&sas_rphy_class);
+}
+
+MODULE_AUTHOR("Christoph Hellwig");
+MODULE_DESCRIPTION("SAS Transphy Attributes");
+MODULE_LICENSE("GPL");
+
+module_init(sas_transport_init);
+module_exit(sas_transport_exit);
diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c
index b1b69d738d0..9ea4765d1d1 100644
--- a/drivers/scsi/sg.c
+++ b/drivers/scsi/sg.c
@@ -61,7 +61,7 @@ static int sg_version_num = 30533;	/* 2 digits for each component */
 
 #ifdef CONFIG_SCSI_PROC_FS
 #include <linux/proc_fs.h>
-static char *sg_version_date = "20050901";
+static char *sg_version_date = "20050908";
 
 static int sg_proc_init(void);
 static void sg_proc_cleanup(void);
@@ -1299,7 +1299,7 @@ sg_mmap(struct file *filp, struct vm_area_struct *vma)
 		sg_rb_correct4mmap(rsv_schp, 1);	/* do only once per fd lifetime */
 		sfp->mmap_called = 1;
 	}
-	vma->vm_flags |= (VM_RESERVED | VM_IO);
+	vma->vm_flags |= VM_RESERVED;
 	vma->vm_private_data = sfp;
 	vma->vm_ops = &sg_mmap_vm_ops;
 	return 0;
diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h
index da63722c012..c0e4c67d836 100644
--- a/include/scsi/scsi_device.h
+++ b/include/scsi/scsi_device.h
@@ -178,8 +178,8 @@ static inline struct scsi_target *scsi_target(struct scsi_device *sdev)
 
 extern struct scsi_device *__scsi_add_device(struct Scsi_Host *,
 		uint, uint, uint, void *hostdata);
-#define scsi_add_device(host, channel, target, lun) \
-	__scsi_add_device(host, channel, target, lun, NULL)
+extern int scsi_add_device(struct Scsi_Host *host, uint channel,
+			   uint target, uint lun);
 extern void scsi_remove_device(struct scsi_device *);
 extern int scsi_device_cancel(struct scsi_device *, int);
 
diff --git a/include/scsi/scsi_transport_fc.h b/include/scsi/scsi_transport_fc.h
index 70ad16315a1..115db056dc6 100644
--- a/include/scsi/scsi_transport_fc.h
+++ b/include/scsi/scsi_transport_fc.h
@@ -439,4 +439,12 @@ int fc_remote_port_block(struct fc_rport *rport);
 void fc_remote_port_unblock(struct fc_rport *rport);
 int scsi_is_fc_rport(const struct device *);
 
+static inline u64 wwn_to_u64(u8 *wwn)
+{
+	return (u64)wwn[0] << 56 | (u64)wwn[1] << 48 |
+	    (u64)wwn[2] << 40 | (u64)wwn[3] << 32 |
+	    (u64)wwn[4] << 24 | (u64)wwn[5] << 16 |
+	    (u64)wwn[6] <<  8 | (u64)wwn[7];
+}
+
 #endif /* SCSI_TRANSPORT_FC_H */
diff --git a/include/scsi/scsi_transport_sas.h b/include/scsi/scsi_transport_sas.h
new file mode 100644
index 00000000000..bc4aeb660dd
--- /dev/null
+++ b/include/scsi/scsi_transport_sas.h
@@ -0,0 +1,100 @@
+#ifndef SCSI_TRANSPORT_SAS_H
+#define SCSI_TRANSPORT_SAS_H
+
+#include <linux/transport_class.h>
+#include <linux/types.h>
+
+struct scsi_transport_template;
+struct sas_rphy;
+
+
+enum sas_device_type {
+	SAS_PHY_UNUSED,
+	SAS_END_DEVICE,
+	SAS_EDGE_EXPANDER_DEVICE,
+	SAS_FANOUT_EXPANDER_DEVICE,
+};
+
+enum sas_protocol {
+	SAS_PROTOCOL_SATA		= 0x01,
+	SAS_PROTOCOL_SMP		= 0x02,
+	SAS_PROTOCOL_STP		= 0x04,
+	SAS_PROTOCOL_SSP		= 0x08,
+};
+
+enum sas_linkrate {
+	SAS_LINK_RATE_UNKNOWN,
+	SAS_PHY_DISABLED,
+	SAS_LINK_RATE_FAILED,
+	SAS_SATA_SPINUP_HOLD,
+	SAS_SATA_PORT_SELECTOR,
+	SAS_LINK_RATE_1_5_GBPS,
+	SAS_LINK_RATE_3_0_GBPS,
+	SAS_LINK_VIRTUAL,
+};
+
+struct sas_identify {
+	enum sas_device_type	device_type;
+	enum sas_protocol	initiator_port_protocols;
+	enum sas_protocol	target_port_protocols;
+	u64			sas_address;
+	u8			phy_identifier;
+};
+
+/* The functions by which the transport class and the driver communicate */
+struct sas_function_template {
+};
+
+struct sas_phy {
+	struct device		dev;
+	int			number;
+	struct sas_identify	identify;
+	enum sas_linkrate	negotiated_linkrate;
+	enum sas_linkrate	minimum_linkrate_hw;
+	enum sas_linkrate	minimum_linkrate;
+	enum sas_linkrate	maximum_linkrate_hw;
+	enum sas_linkrate	maximum_linkrate;
+	u8			port_identifier;
+	struct sas_rphy		*rphy;
+};
+
+#define dev_to_phy(d) \
+	container_of((d), struct sas_phy, dev)
+#define transport_class_to_phy(cdev) \
+	dev_to_phy((cdev)->dev)
+#define phy_to_shost(phy) \
+	dev_to_shost((phy)->dev.parent)
+
+struct sas_rphy {
+	struct device		dev;
+	struct sas_identify	identify;
+	struct list_head	list;
+	u32			scsi_target_id;
+};
+
+#define dev_to_rphy(d) \
+	container_of((d), struct sas_rphy, dev)
+#define transport_class_to_rphy(cdev) \
+	dev_to_rphy((cdev)->dev)
+#define rphy_to_shost(rphy) \
+	dev_to_shost((rphy)->dev.parent)
+
+extern void sas_remove_host(struct Scsi_Host *);
+
+extern struct sas_phy *sas_phy_alloc(struct device *, int);
+extern void sas_phy_free(struct sas_phy *);
+extern int sas_phy_add(struct sas_phy *);
+extern void sas_phy_delete(struct sas_phy *);
+extern int scsi_is_sas_phy(const struct device *);
+
+extern struct sas_rphy *sas_rphy_alloc(struct sas_phy *);
+void sas_rphy_free(struct sas_rphy *);
+extern int sas_rphy_add(struct sas_rphy *);
+extern void sas_rphy_delete(struct sas_rphy *);
+extern int scsi_is_sas_rphy(const struct device *);
+
+extern struct scsi_transport_template *
+sas_attach_transport(struct sas_function_template *);
+extern void sas_release_transport(struct scsi_transport_template *);
+
+#endif /* SCSI_TRANSPORT_SAS_H */