MERGE-via-pending-tracking-hist-MERGE-via-stable-tracking-MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040-1232632141

pending-tracking-hist top was MERGE-via-stable-tracking-MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040-1232632141 / fdf777a63bcb59e0dfd78bfe2c6242e01f6d4eb9 ... parent commitmessage:
From: merge <null@invalid>
MERGE-via-stable-tracking-hist-MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040

stable-tracking-hist top was MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040 / 90463bfd2d5a3c8b52f6e6d71024a00e052b0ced ... parent commitmessage:
From: merge <null@invalid>
MERGE-via-mokopatches-tracking-hist-fix-stray-endmenu-patch

mokopatches-tracking-hist top was fix-stray-endmenu-patch / 3630e0be570de8057e7f8d2fe501ed353cdf34e6 ... parent commitmessage:
From: Andy Green <andy@openmoko.com>
fix-stray-endmenu.patch

Signed-off-by: Andy Green <andy@openmoko.com>

10 files changed, 414 insertions, 26 deletions

diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet
index aef5a9b3684..d9251efdcec 100644
--- a/Documentation/hwmon/abituguru-datasheet
+++ b/Documentation/hwmon/abituguru-datasheet
@@ -74,7 +74,7 @@ a sensor.
 Notice that some banks have both a read and a write address this is how the
 uGuru determines if a read from or a write to the bank is taking place, thus
 when reading you should always use the read address and when writing the
-write address. The write address is always one (1) more then the read address.
+write address. The write address is always one (1) more than the read address.
 
 
 uGuru ready
@@ -121,7 +121,7 @@ Once all bytes have been read data will hold 0x09, but there is no reason to
 test for this. Notice that the number of bytes is bank address dependent see
 above and below.
 
-After completing a successfull read it is advised to put the uGuru back in
+After completing a successful read it is advised to put the uGuru back in
 ready mode, so that it is ready for the next read / write cycle. This way
 if your program / driver is unloaded and later loaded again the detection
 algorithm described above will still work.
@@ -141,7 +141,7 @@ don't ask why this is the way it is.
 
 Once DATA holds 0x01 read CMD it should hold 0xAC now.
 
-After completing a successfull write it is advised to put the uGuru back in
+After completing a successful write it is advised to put the uGuru back in
 ready mode, so that it is ready for the next read / write cycle. This way
 if your program / driver is unloaded and later loaded again the detection
 algorithm described above will still work.
@@ -224,7 +224,7 @@ Bit 3: Beep if alarm							(RW)
 Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
 Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
 Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
-Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds	(RW)
        Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
 
 *  This bit is only honored/used by the uGuru if a temp sensor is connected
@@ -293,7 +293,7 @@ Byte 0:
 Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
 Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
 Bit 3: Beep if alarm						(RW)
-Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Shutdown if alarm persist for more than 4 seconds	(RW)
 
 Byte 1:
 min threshold (scale as bank 0x26)
diff --git a/Documentation/hwmon/adt7462 b/Documentation/hwmon/adt7462
new file mode 100644
index 00000000000..ec660b32827
--- /dev/null
+++ b/Documentation/hwmon/adt7462
@@ -0,0 +1,67 @@
+Kernel driver adt7462
+======================
+
+Supported chips:
+  * Analog Devices ADT7462
+    Prefix: 'adt7462'
+    Addresses scanned: I2C 0x58, 0x5C
+    Datasheet: Publicly available at the Analog Devices website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the Analog Devices ADT7462 chip family.
+
+This chip is a bit of a beast.  It has 8 counters for measuring fan speed.  It
+can also measure 13 voltages or 4 temperatures, or various combinations of the
+two.  See the chip documentation for more details about the exact set of
+configurations.  This driver does not allow one to configure the chip; that is
+left to the system designer.
+
+A sophisticated control system for the PWM outputs is designed into the ADT7462
+that allows fan speed to be adjusted automatically based on any of the three
+temperature sensors. Each PWM output is individually adjustable and
+programmable. Once configured, the ADT7462 will adjust the PWM outputs in
+response to the measured temperatures without further host intervention.  This
+feature can also be disabled for manual control of the PWM's.
+
+Each of the measured inputs (voltage, temperature, fan speed) has
+corresponding high/low limit values. The ADT7462 will signal an ALARM if
+any measured value exceeds either limit.
+
+The ADT7462 samples all inputs continuously. The driver will not read
+the registers more often than once every other second. Further,
+configuration data is only read once per minute.
+
+Special Features
+----------------
+
+The ADT7462 have a 10-bit ADC and can therefore measure temperatures
+with 0.25 degC resolution.
+
+The Analog Devices datasheet is very detailed and describes a procedure for
+determining an optimal configuration for the automatic PWM control.
+
+The driver will report sensor labels when it is able to determine that
+information from the configuration registers.
+
+Configuration Notes
+-------------------
+
+Besides standard interfaces driver adds the following:
+
+* PWM Control
+
+* pwm#_auto_point1_pwm and temp#_auto_point1_temp and
+* pwm#_auto_point2_pwm and temp#_auto_point2_temp -
+
+point1: Set the pwm speed at a lower temperature bound.
+point2: Set the pwm speed at a higher temperature bound.
+
+The ADT7462 will scale the pwm between the lower and higher pwm speed when
+the temperature is between the two temperature boundaries.  PWM values range
+from 0 (off) to 255 (full speed).  Fan speed will be set to maximum when the
+temperature sensor associated with the PWM control exceeds temp#_max.
+
diff --git a/Documentation/hwmon/adt7470 b/Documentation/hwmon/adt7470
index 75d13ca147c..8ce4aa0a0f5 100644
--- a/Documentation/hwmon/adt7470
+++ b/Documentation/hwmon/adt7470
@@ -31,15 +31,11 @@ Each of the measured inputs (temperature, fan speed) has corresponding high/low
 limit values. The ADT7470 will signal an ALARM if any measured value exceeds
 either limit.
 
-The ADT7470 DOES NOT sample all inputs continuously.  A single pin on the
-ADT7470 is connected to a multitude of thermal diodes, but the chip must be
-instructed explicitly to read the multitude of diodes.  If you want to use
-automatic fan control mode, you must manually read any of the temperature
-sensors or the fan control algorithm will not run.  The chip WILL NOT DO THIS
-AUTOMATICALLY; this must be done from userspace.  This may be a bug in the chip
-design, given that many other AD chips take care of this.  The driver will not
-read the registers more often than once every 5 seconds.  Further,
-configuration data is only read once per minute.
+The ADT7470 samples all inputs continuously.  A kernel thread is started up for
+the purpose of periodically querying the temperature sensors, thus allowing the
+automatic fan pwm control to set the fan speed.  The driver will not read the
+registers more often than once every 5 seconds.  Further, configuration data is
+only read once per minute.
 
 Special Features
 ----------------
@@ -72,5 +68,6 @@ pwm#_auto_point2_temp.
 Notes
 -----
 
-As stated above, the temperature inputs must be read periodically from
-userspace in order for the automatic pwm algorithm to run.
+The temperature inputs no longer need to be read periodically from userspace in
+order for the automatic pwm algorithm to run.  This was the case for earlier
+versions of the driver.
diff --git a/Documentation/hwmon/adt7475 b/Documentation/hwmon/adt7475
new file mode 100644
index 00000000000..a2b1abec850
--- /dev/null
+++ b/Documentation/hwmon/adt7475
@@ -0,0 +1,87 @@
+This describes the interface for the ADT7475 driver:
+
+(there are 4 fans, numbered fan1 to fan4):
+
+fanX_input		Read the current speed of the fan (in RPMs)
+fanX_min		Read/write the minimum speed of the fan.  Dropping
+			below this sets an alarm.
+
+(there are three PWMs, numbered pwm1 to pwm3):
+
+pwmX			Read/write the current duty cycle of the PWM.  Writes
+			only have effect when auto mode is turned off (see
+			below).  Range is 0 - 255.
+
+pwmX_enable		Fan speed control method:
+
+			0 - No control (fan at full speed)
+			1 - Manual fan speed control (using pwm[1-*])
+			2 - Automatic fan speed control
+
+pwmX_auto_channels_temp	Select which channels affect this PWM
+
+			1 - TEMP1 controls PWM
+			2 - TEMP2 controls PWM
+			4 - TEMP3 controls PWM
+			6 - TEMP2 and TEMP3 control PWM
+			7 - All three inputs control PWM
+
+pwmX_freq		Read/write the PWM frequency in Hz. The number
+			should be one of the following:
+
+			11 Hz
+			14 Hz
+			22 Hz
+			29 Hz
+			35 Hz
+			44 Hz
+			58 Hz
+			88 Hz
+
+pwmX_auto_point1_pwm	Read/write the minimum PWM duty cycle in automatic mode
+
+pwmX_auto_point2_pwm	Read/write the maximum PWM duty cycle in automatic mode
+
+(there are three temperature settings numbered temp1 to temp3):
+
+tempX_input		Read the current temperature.  The value is in milli
+			degrees of Celsius.
+
+tempX_max		Read/write the upper temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_min		Read/write the lower temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_offset		Read/write the temperature adjustment offset
+
+tempX_crit		Read/write the THERM limit for remote1.
+
+tempX_crit_hyst		Set the temperature value below crit where the
+			fans will stay on - this helps drive the temperature
+			low enough so it doesn't stay near the edge and
+			cause THERM to keep tripping.
+
+tempX_auto_point1_temp	Read/write the minimum temperature where the fans will
+			turn on in automatic mode.
+
+tempX_auto_point2_temp	Read/write the maximum temperature over which the fans
+			will run in automatic mode.  tempX_auto_point1_temp
+			and tempX_auto_point2_temp together define the
+			range of automatic control.
+
+tempX_alarm		Read a 1 if the max/min alarm is set
+tempX_fault		Read a 1 if either temp1 or temp3 diode has a fault
+
+(There are two voltage settings, in1 and in2):
+
+inX_input		Read the current voltage on VCC.  Value is in
+			millivolts.
+
+inX_min			read/write the minimum voltage limit.
+			Dropping below this causes an alarm.
+
+inX_max			read/write the maximum voltage limit.
+			Exceeding this causes an alarm.
+
+inX_alarm		Read a 1 if the max/min alarm is set.
diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
new file mode 100644
index 00000000000..a8321267b5b
--- /dev/null
+++ b/Documentation/hwmon/f71882fg
@@ -0,0 +1,89 @@
+Kernel driver f71882fg
+======================
+
+Supported chips:
+  * Fintek F71882FG and F71883FG
+    Prefix: 'f71882fg'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Available from the Fintek website
+  * Fintek F71862FG and F71863FG
+    Prefix: 'f71862fg'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Available from the Fintek website
+  * Fintek F8000
+    Prefix: 'f8000'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Not public
+
+Author: Hans de Goede <hdegoede@redhat.com>
+
+
+Description
+-----------
+
+Fintek F718xxFG/F8000 Super I/O chips include complete hardware monitoring
+capabilities. They can monitor up to 9 voltages (3 for the F8000), 4 fans and
+3 temperature sensors.
+
+These chips also have fan controlling features, using either DC or PWM, in
+three different modes (one manual, two automatic).
+
+The driver assumes that no more than one chip is present, which seems
+reasonable.
+
+
+Monitoring
+----------
+
+The Voltage, Fan and Temperature Monitoring uses the standard sysfs
+interface as documented in sysfs-interface, without any exceptions.
+
+
+Fan Control
+-----------
+
+Both PWM (pulse-width modulation) and DC fan speed control methods are
+supported. The right one to use depends on external circuitry on the
+motherboard, so the driver assumes that the BIOS set the method
+properly.
+
+There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
+voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
+mode where the actual RPM of the fan (as measured) is controlled and the speed
+gets specified as 0-100% of the fan#_full_speed file.
+
+Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a
+whole lot of a difference when modifying fan control settings. The only
+important difference is that in RPM mode the 0-100% controls the fan speed
+between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs
+RPM mode, it will also set fan#_full_speed properly, if it does not then
+fan control will not work properly, unless you set a sane fan#_full_speed
+value yourself.
+
+Switching between these modes requires re-initializing a whole bunch of
+registers, so the mode which the BIOS has set is kept. The mode is
+printed when loading the driver.
+
+Three different fan control modes are supported; the mode number is written
+to the pwm#_enable file. Note that not all modes are supported on all
+chips, and some modes may only be available in RPM / PWM mode on the F8000.
+Writing an unsupported mode will result in an invalid parameter error.
+
+* 1: Manual mode
+  You ask for a specific PWM duty cycle / DC voltage or a specific % of
+  fan#_full_speed by writing to the pwm# file. This mode is only
+  available on the F8000 if the fan channel is in RPM mode.
+
+* 2: Normal auto mode
+  You can define a number of temperature/fan speed trip points, which % the
+  fan should run at at this temp and which temp a fan should follow using the
+  standard sysfs interface. The number and type of trip points is chip
+  depended, see which files are available in sysfs.
+  Fan/PWM channel 3 of the F8000 is always in this mode!
+
+* 3: Thermostat mode (Only available on the F8000 when in duty cycle mode)
+  The fan speed is regulated to keep the temp the fan is mapped to between
+  temp#_auto_point2_temp and temp#_auto_point3_temp.
+
+Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
+fan2 and pwm3 to fan3.
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index 042c0415140..659315d98e0 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -26,6 +26,10 @@ Supported chips:
     Datasheet: Publicly available at the ITE website
                http://www.ite.com.tw/product_info/file/pc/IT8718F_V0.2.zip
                http://www.ite.com.tw/product_info/file/pc/IT8718F_V0%203_(for%20C%20version).zip
+  * IT8720F
+    Prefix: 'it8720'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not yet publicly available.
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -71,7 +75,7 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8726F and SiS950 chips.
+IT8718F, IT8720F, IT8726F and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -84,19 +88,19 @@ the IT8716F and late IT8712F have 6. They are shared with other functions
 though, so the functionality may not be available on a given system.
 The driver dumbly assume it is there.
 
-The IT8718F also features VID inputs (up to 8 pins) but the value is
-stored in the Super-I/O configuration space. Due to technical limitations,
+The IT8718F and IT8720F also features VID inputs (up to 8 pins) but the value
+is stored in the Super-I/O configuration space. Due to technical limitations,
 this value can currently only be read once at initialization time, so
 the driver won't notice and report changes in the VID value. The two
 upper VID bits share their pins with voltage inputs (in5 and in6) so you
 can't have both on a given board.
 
-The IT8716F, IT8718F and later IT8712F revisions have support for
+The IT8716F, IT8718F, IT8720F and later IT8712F revisions have support for
 2 additional fans. The additional fans are supported by the driver.
 
-The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
-16-bit tachometer counters for fans 1 to 3. This is better (no more fan
-clock divider mess) but not compatible with the older chips and
+The IT8716F, IT8718F and IT8720F, and late IT8712F and IT8705F also have
+optional 16-bit tachometer counters for fans 1 to 3. This is better (no more
+fan clock divider mess) but not compatible with the older chips and
 revisions. The 16-bit tachometer mode is enabled by the driver when one
 of the above chips is detected.
 
@@ -122,7 +126,7 @@ zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
 0.016 volt. The battery voltage in8 does not have limit registers.
 
-The VID lines (IT8712F/IT8716F/IT8718F) encode the core voltage value:
+The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
 the voltage level your processor should work with. This is hardcoded by
 the mainboard and/or processor itself. It is a value in volts.
 
diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d
new file mode 100644
index 00000000000..0fcfc4a7ccd
--- /dev/null
+++ b/Documentation/hwmon/lis3lv02d
@@ -0,0 +1,53 @@
+Kernel driver lis3lv02d
+==================
+
+Supported chips:
+
+  * STMicroelectronics LIS3LV02DL and LIS3LV02DQ
+
+Author:
+        Yan Burman <burman.yan@gmail.com>
+	Eric Piel <eric.piel@tremplin-utc.net>
+
+
+Description
+-----------
+
+This driver provides support for the accelerometer found in various HP
+laptops sporting the feature officially called "HP Mobile Data
+Protection System 3D" or "HP 3D DriveGuard". It detect automatically
+laptops with this sensor. Known models (for now the HP 2133, nc6420,
+nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis
+automatically oriented on standard way (eg: you can directly play
+neverball).  The accelerometer data is readable via
+/sys/devices/platform/lis3lv02d.
+
+Sysfs attributes under /sys/devices/platform/lis3lv02d/:
+position - 3D position that the accelerometer reports. Format: "(x,y,z)"
+calibrate - read: values (x, y, z) that are used as the base for input
+		  class device operation.
+            write: forces the base to be recalibrated with the current
+		  position.
+rate - reports the sampling rate of the accelerometer device in HZ
+
+This driver also provides an absolute input class device, allowing
+the laptop to act as a pinball machine-esque joystick.
+
+Axes orientation
+----------------
+
+For better compatibility between the various laptops. The values reported by
+the accelerometer are converted into a "standard" organisation of the axes
+(aka "can play neverball out of the box"):
+ * When the laptop is horizontal the position reported is about 0 for X and Y
+and a positive value for Z
+ * If the left side is elevated, X increases (becomes positive)
+ * If the front side (where the touchpad is) is elevated, Y decreases
+	(becomes negative)
+ * If the laptop is put upside-down, Z becomes negative
+
+If your laptop model is not recognized (cf "dmesg"), you can send an
+email to the authors to add it to the database.  When reporting a new
+laptop, please include the output of "dmidecode" plus the value of
+/sys/devices/platform/lis3lv02d/position in these four cases.
+
diff --git a/Documentation/hwmon/lm70 b/Documentation/hwmon/lm70
index 2bdd3feebf5..0d240291e3c 100644
--- a/Documentation/hwmon/lm70
+++ b/Documentation/hwmon/lm70
@@ -1,9 +1,11 @@
 Kernel driver lm70
 ==================
 
-Supported chip:
+Supported chips:
   * National Semiconductor LM70
     Datasheet: http://www.national.com/pf/LM/LM70.html
+  * Texas Instruments TMP121/TMP123
+    Information: http://focus.ti.com/docs/prod/folders/print/tmp121.html
 
 Author:
         Kaiwan N Billimoria <kaiwan@designergraphix.com>
@@ -25,6 +27,14 @@ complement digital temperature (sent via the SIO line), is available in the
 driver for interpretation. This driver makes use of the kernel's in-core
 SPI support.
 
+As a real (in-tree) example of this "SPI protocol driver" interfacing
+with a "SPI master controller driver", see drivers/spi/spi_lm70llp.c
+and its associated documentation.
+
+The TMP121/TMP123 are very similar; main differences are 4 wire SPI inter-
+face (read only) and 13-bit temperature data (0.0625 degrees celsius reso-
+lution).
+
 Thanks to
 ---------
 Jean Delvare <khali@linux-fr.org> for mentoring the hwmon-side driver
diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 40062074129..a13680871bc 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -164,7 +164,7 @@ configured individually according to the following options.
                       temperature. (PWM value from 0 to 255)
 
 * pwm#_auto_pwm_minctl - this flags selects for temp#_auto_temp_off temperature
-                         the bahaviour of fans. Write 1 to let fans spinning at
+                         the behaviour of fans. Write 1 to let fans spinning at
 			 pwm#_auto_pwm_min or write 0 to let them off.
 
 NOTE: It has been reported that there is a bug in the LM85 that causes the flag
diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245
new file mode 100644
index 00000000000..bae7a3adc5d
--- /dev/null
+++ b/Documentation/hwmon/ltc4245
@@ -0,0 +1,81 @@
+Kernel driver ltc4245
+=====================
+
+Supported chips:
+  * Linear Technology LTC4245
+    Prefix: 'ltc4245'
+    Addresses scanned: 0x20-0x3f
+    Datasheet:
+        http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517
+
+Author: Ira W. Snyder <iws@ovro.caltech.edu>
+
+
+Description
+-----------
+
+The LTC4245 controller allows a board to be safely inserted and removed
+from a live backplane in multiple supply systems such as CompactPCI and
+PCI Express.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4245 devices, due to the fact that some
+of the possible addresses are unfriendly to probing. You will need to use
+the "force" parameter to tell the driver where to find the device.
+
+Example: the following will load the driver for an LTC4245 at address 0x23
+on I2C bus #1:
+$ modprobe ltc4245 force=1,0x23
+
+
+Sysfs entries
+-------------
+
+The LTC4245 has built-in limits for over and under current warnings. This
+makes it very likely that the reference circuit will be used.
+
+This driver uses the values in the datasheet to change the register values
+into the values specified in the sysfs-interface document. The current readings
+rely on the sense resistors listed in Table 2: "Sense Resistor Values".
+
+in1_input		12v input voltage (mV)
+in2_input		5v  input voltage (mV)
+in3_input		3v  input voltage (mV)
+in4_input		Vee (-12v) input voltage (mV)
+
+in1_min_alarm		12v input undervoltage alarm
+in2_min_alarm		5v  input undervoltage alarm
+in3_min_alarm		3v  input undervoltage alarm
+in4_min_alarm		Vee (-12v) input undervoltage alarm
+
+curr1_input		12v current (mA)
+curr2_input		5v  current (mA)
+curr3_input		3v  current (mA)
+curr4_input		Vee (-12v) current (mA)
+
+curr1_max_alarm		12v overcurrent alarm
+curr2_max_alarm		5v  overcurrent alarm
+curr3_max_alarm		3v  overcurrent alarm
+curr4_max_alarm		Vee (-12v) overcurrent alarm
+
+in5_input		12v output voltage (mV)
+in6_input		5v  output voltage (mV)
+in7_input		3v  output voltage (mV)
+in8_input		Vee (-12v) output voltage (mV)
+
+in5_min_alarm		12v output undervoltage alarm
+in6_min_alarm		5v  output undervoltage alarm
+in7_min_alarm		3v  output undervoltage alarm
+in8_min_alarm		Vee (-12v) output undervoltage alarm
+
+in9_input		GPIO #1 voltage data
+in10_input		GPIO #2 voltage data
+in11_input		GPIO #3 voltage data
+
+power1_input		12v power usage (mW)
+power2_input		5v  power usage (mW)
+power3_input		3v  power usage (mW)
+power4_input		Vee (-12v) power usage (mW)