diff options
Diffstat (limited to 'Documentation/sound')
| -rw-r--r-- | Documentation/sound/alsa/ALSA-Configuration.txt | 69 | ||||
| -rw-r--r-- | Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl | 16 |
2 files changed, 77 insertions, 8 deletions
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt index 1def6049784..0ee2c7dfc48 100644 --- a/Documentation/sound/alsa/ALSA-Configuration.txt +++ b/Documentation/sound/alsa/ALSA-Configuration.txt @@ -120,6 +120,34 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. enable - enable card - Default: enabled, for PCI and ISA PnP cards + Module snd-adlib + ---------------- + + Module for AdLib FM cards. + + port - port # for OPL chip + + This module supports multiple cards. It does not support autoprobe, so + the port must be specified. For actual AdLib FM cards it will be 0x388. + Note that this card does not have PCM support and no mixer; only FM + synthesis. + + Make sure you have "sbiload" from the alsa-tools package available and, + after loading the module, find out the assigned ALSA sequencer port + number through "sbiload -l". Example output: + + Port Client name Port name + 64:0 OPL2 FM synth OPL2 FM Port + + Load the std.sb and drums.sb patches also supplied by sbiload: + + sbiload -p 64:0 std.sb drums.sb + + If you use this driver to drive an OPL3, you can use std.o3 and drums.o3 + instead. To have the card produce sound, use aplaymidi from alsa-utils: + + aplaymidi -p 64:0 foo.mid + Module snd-ad1816a ------------------ @@ -190,6 +218,15 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. The power-management is supported. + Module snd-als300 + ----------------- + + Module for Avance Logic ALS300 and ALS300+ + + This module supports multiple cards. + + The power-management is supported. + Module snd-als4000 ------------------ @@ -701,6 +738,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. uniwill 3-jack F1734 2-jack lg LG laptop (m1 express dual) + lg-lw LG LW20 laptop test for testing/debugging purpose, almost all controls can be adjusted. Appearing only when compiled with $CONFIG_SND_DEBUG=y @@ -1013,6 +1051,23 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. The power-management is supported. + Module snd-miro + --------------- + + Module for Miro soundcards: miroSOUND PCM 1 pro, + miroSOUND PCM 12, + miroSOUND PCM 20 Radio. + + port - Port # (0x530,0x604,0xe80,0xf40) + irq - IRQ # (5,7,9,10,11) + dma1 - 1st dma # (0,1,3) + dma2 - 2nd dma # (0,1) + mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330) + mpu_irq - MPU-401 irq # (5,7,9,10) + fm_port - FM Port # (0x388) + wss - enable WSS mode + ide - enable onboard ide support + Module snd-mixart ----------------- @@ -1202,6 +1257,20 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. The power-management is supported. + Module snd-riptide + ------------------ + + Module for Conexant Riptide chip + + joystick_port - Joystick port # (default: 0x200) + mpu_port - MPU401 port # (default: 0x330) + opl3_port - OPL3 port # (default: 0x388) + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + You need to install the firmware file "riptide.hex" to the standard + firmware path (e.g. /lib/firmware). + Module snd-rme32 ---------------- diff --git a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl index 6feef9e82b6..68eeebc17ff 100644 --- a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl +++ b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl @@ -1123,8 +1123,8 @@ if ((err = pci_enable_device(pci)) < 0) return err; /* check PCI availability (28bit DMA) */ - if (pci_set_dma_mask(pci, 0x0fffffff) < 0 || - pci_set_consistent_dma_mask(pci, 0x0fffffff) < 0) { + if (pci_set_dma_mask(pci, DMA_28BIT_MASK) < 0 || + pci_set_consistent_dma_mask(pci, DMA_28BIT_MASK) < 0) { printk(KERN_ERR "error to set 28bit mask DMA\n"); pci_disable_device(pci); return -ENXIO; @@ -1216,7 +1216,7 @@ The allocation of PCI resources is done in the <function>probe()</function> function, and usually an extra <function>xxx_create()</function> function is written for this - purpose. + purpose. </para> <para> @@ -1225,7 +1225,7 @@ allocating resources. Also, you need to set the proper PCI DMA mask to limit the accessed i/o range. In some cases, you might need to call <function>pci_set_master()</function> function, - too. + too. </para> <para> @@ -1236,8 +1236,8 @@ <![CDATA[ if ((err = pci_enable_device(pci)) < 0) return err; - if (pci_set_dma_mask(pci, 0x0fffffff) < 0 || - pci_set_consistent_dma_mask(pci, 0x0fffffff) < 0) { + if (pci_set_dma_mask(pci, DMA_28BIT_MASK) < 0 || + pci_set_consistent_dma_mask(pci, DMA_28BIT_MASK) < 0) { printk(KERN_ERR "error to set 28bit mask DMA\n"); pci_disable_device(pci); return -ENXIO; @@ -1256,13 +1256,13 @@ functions. Unlike ALSA ver.0.5.x., there are no helpers for that. And these resources must be released in the destructor function (see below). Also, on ALSA 0.9.x, you don't need to - allocate (pseudo-)DMA for PCI like ALSA 0.5.x. + allocate (pseudo-)DMA for PCI like ALSA 0.5.x. </para> <para> Now assume that this PCI device has an I/O port with 8 bytes and an interrupt. Then struct <structname>mychip</structname> will have the - following fields: + following fields: <informalexample> <programlisting> |