diff options
Diffstat (limited to 'Documentation')
25 files changed, 834 insertions, 108 deletions
diff --git a/Documentation/DMA-API.txt b/Documentation/DMA-API.txt index 1af0f2d5022..2ffb0d62f0f 100644 --- a/Documentation/DMA-API.txt +++ b/Documentation/DMA-API.txt @@ -33,7 +33,9 @@ pci_alloc_consistent(struct pci_dev *dev, size_t size, Consistent memory is memory for which a write by either the device or the processor can immediately be read by the processor or device -without having to worry about caching effects. +without having to worry about caching effects. (You may however need +to make sure to flush the processor's write buffers before telling +devices to read that memory.) This routine allocates a region of <size> bytes of consistent memory. it also returns a <dma_handle> which may be cast to an unsigned @@ -304,12 +306,12 @@ dma address with dma_mapping_error(). A non zero return value means the mapping could not be created and the driver should take appropriate action (eg reduce current DMA mapping usage or delay and try again later). -int -dma_map_sg(struct device *dev, struct scatterlist *sg, int nents, - enum dma_data_direction direction) -int -pci_map_sg(struct pci_dev *hwdev, struct scatterlist *sg, - int nents, int direction) + int + dma_map_sg(struct device *dev, struct scatterlist *sg, + int nents, enum dma_data_direction direction) + int + pci_map_sg(struct pci_dev *hwdev, struct scatterlist *sg, + int nents, int direction) Maps a scatter gather list from the block layer. @@ -327,12 +329,33 @@ critical that the driver do something, in the case of a block driver aborting the request or even oopsing is better than doing nothing and corrupting the filesystem. -void -dma_unmap_sg(struct device *dev, struct scatterlist *sg, int nhwentries, - enum dma_data_direction direction) -void -pci_unmap_sg(struct pci_dev *hwdev, struct scatterlist *sg, - int nents, int direction) +With scatterlists, you use the resulting mapping like this: + + int i, count = dma_map_sg(dev, sglist, nents, direction); + struct scatterlist *sg; + + for (i = 0, sg = sglist; i < count; i++, sg++) { + hw_address[i] = sg_dma_address(sg); + hw_len[i] = sg_dma_len(sg); + } + +where nents is the number of entries in the sglist. + +The implementation is free to merge several consecutive sglist entries +into one (e.g. with an IOMMU, or if several pages just happen to be +physically contiguous) and returns the actual number of sg entries it +mapped them to. On failure 0, is returned. + +Then you should loop count times (note: this can be less than nents times) +and use sg_dma_address() and sg_dma_len() macros where you previously +accessed sg->address and sg->length as shown above. + + void + dma_unmap_sg(struct device *dev, struct scatterlist *sg, + int nhwentries, enum dma_data_direction direction) + void + pci_unmap_sg(struct pci_dev *hwdev, struct scatterlist *sg, + int nents, int direction) unmap the previously mapped scatter/gather list. All the parameters must be the same as those and passed in to the scatter/gather mapping diff --git a/Documentation/DMA-mapping.txt b/Documentation/DMA-mapping.txt index 10bf4deb96a..7c717699032 100644 --- a/Documentation/DMA-mapping.txt +++ b/Documentation/DMA-mapping.txt @@ -58,11 +58,15 @@ translating each of those pages back to a kernel address using something like __va(). [ EDIT: Update this when we integrate Gerd Knorr's generic code which does this. ] -This rule also means that you may not use kernel image addresses -(ie. items in the kernel's data/text/bss segment, or your driver's) -nor may you use kernel stack addresses for DMA. Both of these items -might be mapped somewhere entirely different than the rest of physical -memory. +This rule also means that you may use neither kernel image addresses +(items in data/text/bss segments), nor module image addresses, nor +stack addresses for DMA. These could all be mapped somewhere entirely +different than the rest of physical memory. Even if those classes of +memory could physically work with DMA, you'd need to ensure the I/O +buffers were cacheline-aligned. Without that, you'd see cacheline +sharing problems (data corruption) on CPUs with DMA-incoherent caches. +(The CPU could write to one word, DMA would write to a different one +in the same cache line, and one of them could be overwritten.) Also, this means that you cannot take the return of a kmap() call and DMA to/from that. This is similar to vmalloc(). @@ -284,6 +288,11 @@ There are two types of DMA mappings: in order to get correct behavior on all platforms. + Also, on some platforms your driver may need to flush CPU write + buffers in much the same way as it needs to flush write buffers + found in PCI bridges (such as by reading a register's value + after writing it). + - Streaming DMA mappings which are usually mapped for one DMA transfer, unmapped right after it (unless you use pci_dma_sync_* below) and for which hardware can optimize for sequential accesses. @@ -303,6 +312,9 @@ There are two types of DMA mappings: Neither type of DMA mapping has alignment restrictions that come from PCI, although some devices may have such restrictions. +Also, systems with caches that aren't DMA-coherent will work better +when the underlying buffers don't share cache lines with other data. + Using Consistent DMA mappings. diff --git a/Documentation/HOWTO b/Documentation/HOWTO index 6c9e746267d..915ae8c986c 100644 --- a/Documentation/HOWTO +++ b/Documentation/HOWTO @@ -603,7 +603,8 @@ start exactly where you are now. ---------- -Thanks to Paolo Ciarrocchi who allowed the "Development Process" section +Thanks to Paolo Ciarrocchi who allowed the "Development Process" +(http://linux.tar.bz/articles/2.6-development_process) section to be based on text he had written, and to Randy Dunlap and Gerrit Huizenga for some of the list of things you should and should not say. Also thanks to Pat Mochel, Hanna Linder, Randy Dunlap, Kay Sievers, diff --git a/Documentation/block/switching-sched.txt b/Documentation/block/switching-sched.txt new file mode 100644 index 00000000000..5fa130a6753 --- /dev/null +++ b/Documentation/block/switching-sched.txt @@ -0,0 +1,22 @@ +As of the Linux 2.6.10 kernel, it is now possible to change the +IO scheduler for a given block device on the fly (thus making it possible, +for instance, to set the CFQ scheduler for the system default, but +set a specific device to use the anticipatory or noop schedulers - which +can improve that device's throughput). + +To set a specific scheduler, simply do this: + +echo SCHEDNAME > /sys/block/DEV/queue/scheduler + +where SCHEDNAME is the name of a defined IO scheduler, and DEV is the +device name (hda, hdb, sga, or whatever you happen to have). + +The list of defined schedulers can be found by simply doing +a "cat /sys/block/DEV/queue/scheduler" - the list of valid names +will be displayed, with the currently selected scheduler in brackets: + +# cat /sys/block/hda/queue/scheduler +noop anticipatory deadline [cfq] +# echo anticipatory > /sys/block/hda/queue/scheduler +# cat /sys/block/hda/queue/scheduler +noop [anticipatory] deadline cfq diff --git a/Documentation/cpu-freq/index.txt b/Documentation/cpu-freq/index.txt index 5009805f937..ffdb5323df3 100644 --- a/Documentation/cpu-freq/index.txt +++ b/Documentation/cpu-freq/index.txt @@ -53,4 +53,4 @@ the CPUFreq Mailing list: * http://lists.linux.org.uk/mailman/listinfo/cpufreq Clock and voltage scaling for the SA-1100: -* http://www.lart.tudelft.nl/projects/scaling +* http://www.lartmaker.nl/projects/scaling diff --git a/Documentation/devices.txt b/Documentation/devices.txt index 3c406acd4df..b369a8c46a7 100644 --- a/Documentation/devices.txt +++ b/Documentation/devices.txt @@ -1721,11 +1721,6 @@ Your cooperation is appreciated. These devices support the same API as the generic SCSI devices. - 97 block Packet writing for CD/DVD devices - 0 = /dev/pktcdvd0 First packet-writing module - 1 = /dev/pktcdvd1 Second packet-writing module - ... - 98 char Control and Measurement Device (comedi) 0 = /dev/comedi0 First comedi device 1 = /dev/comedi1 Second comedi device diff --git a/Documentation/dvb/get_dvb_firmware b/Documentation/dvb/get_dvb_firmware index 15fc8fbef67..4820366b6ae 100644 --- a/Documentation/dvb/get_dvb_firmware +++ b/Documentation/dvb/get_dvb_firmware @@ -259,9 +259,9 @@ sub dibusb { } sub nxt2002 { - my $sourcefile = "Broadband4PC_4_2_11.zip"; + my $sourcefile = "Technisat_DVB-PC_4_4_COMPACT.zip"; my $url = "http://www.bbti.us/download/windows/$sourcefile"; - my $hash = "c6d2ea47a8f456d887ada0cfb718ff2a"; + my $hash = "476befae8c7c1bb9648954060b1eec1f"; my $outfile = "dvb-fe-nxt2002.fw"; my $tmpdir = tempdir(DIR => "/tmp", CLEANUP => 1); @@ -269,8 +269,8 @@ sub nxt2002 { wgetfile($sourcefile, $url); unzip($sourcefile, $tmpdir); - verify("$tmpdir/SkyNETU.sys", $hash); - extract("$tmpdir/SkyNETU.sys", 375832, 5908, $outfile); + verify("$tmpdir/SkyNET.sys", $hash); + extract("$tmpdir/SkyNET.sys", 331624, 5908, $outfile); $outfile; } diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 293fed113df..43ab119963d 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -25,8 +25,9 @@ Who: Adrian Bunk <bunk@stusta.de> --------------------------- -What: drivers depending on OBSOLETE_OSS_DRIVER -When: January 2006 +What: drivers that were depending on OBSOLETE_OSS_DRIVER + (config options already removed) +When: before 2.6.19 Why: OSS drivers with ALSA replacements Who: Adrian Bunk <bunk@stusta.de> @@ -56,6 +57,15 @@ Who: Jody McIntyre <scjody@steamballoon.com> --------------------------- +What: sbp2: module parameter "force_inquiry_hack" +When: July 2006 +Why: Superceded by parameter "workarounds". Both parameters are meant to be + used ad-hoc and for single devices only, i.e. not in modprobe.conf, + therefore the impact of this feature replacement should be low. +Who: Stefan Richter <stefanr@s5r6.in-berlin.de> + +--------------------------- + What: Video4Linux API 1 ioctls and video_decoder.h from Video devices. When: July 2006 Why: V4L1 AP1 was replaced by V4L2 API. during migration from 2.4 to 2.6 diff --git a/Documentation/filesystems/sysfs.txt b/Documentation/filesystems/sysfs.txt index c8bce82ddca..89b1d196ca8 100644 --- a/Documentation/filesystems/sysfs.txt +++ b/Documentation/filesystems/sysfs.txt @@ -246,6 +246,7 @@ class/ devices/ firmware/ net/ +fs/ devices/ contains a filesystem representation of the device tree. It maps directly to the internal kernel device tree, which is a hierarchy of @@ -264,6 +265,10 @@ drivers/ contains a directory for each device driver that is loaded for devices on that particular bus (this assumes that drivers do not span multiple bus types). +fs/ contains a directory for some filesystems. Currently each +filesystem wanting to export attributes must create its own hierarchy +below fs/ (see ./fuse.txt for an example). + More information can driver-model specific features can be found in Documentation/driver-model/. diff --git a/Documentation/firmware_class/README b/Documentation/firmware_class/README index 43e836c07ae..e9cc8bb26f7 100644 --- a/Documentation/firmware_class/README +++ b/Documentation/firmware_class/README @@ -105,20 +105,3 @@ on the setup, so I think that the choice on what firmware to make persistent should be left to userspace. - - Why register_firmware()+__init can be useful: - - For boot devices needing firmware. - - To make the transition easier: - The firmware can be declared __init and register_firmware() - called on module_init. Then the firmware is warranted to be - there even if "firmware hotplug userspace" is not there yet or - it doesn't yet provide the needed firmware. - Once the firmware is widely available in userspace, it can be - removed from the kernel. Or made optional (CONFIG_.*_FIRMWARE). - - In either case, if firmware hotplug support is there, it can move the - firmware out of kernel memory into the real filesystem for later - usage. - - Note: If persistence is implemented on top of initramfs, - register_firmware() may not be appropriate. - diff --git a/Documentation/firmware_class/firmware_sample_driver.c b/Documentation/firmware_class/firmware_sample_driver.c index ad3edaba453..87feccdb5c9 100644 --- a/Documentation/firmware_class/firmware_sample_driver.c +++ b/Documentation/firmware_class/firmware_sample_driver.c @@ -5,8 +5,6 @@ * * Sample code on how to use request_firmware() from drivers. * - * Note that register_firmware() is currently useless. - * */ #include <linux/module.h> @@ -17,11 +15,6 @@ #include "linux/firmware.h" -#define WE_CAN_NEED_FIRMWARE_BEFORE_USERSPACE_IS_AVAILABLE -#ifdef WE_CAN_NEED_FIRMWARE_BEFORE_USERSPACE_IS_AVAILABLE -char __init inkernel_firmware[] = "let's say that this is firmware\n"; -#endif - static struct device ghost_device = { .bus_id = "ghost0", }; @@ -104,10 +97,6 @@ static void sample_probe_async(void) static int sample_init(void) { -#ifdef WE_CAN_NEED_FIRMWARE_BEFORE_USERSPACE_IS_AVAILABLE - register_firmware("sample_driver_fw", inkernel_firmware, - sizeof(inkernel_firmware)); -#endif device_initialize(&ghost_device); /* since there is no real hardware insertion I just call the * sample probe functions here */ diff --git a/Documentation/i2c/busses/i2c-parport b/Documentation/i2c/busses/i2c-parport index d9f23c0763f..77b995dfca2 100644 --- a/Documentation/i2c/busses/i2c-parport +++ b/Documentation/i2c/busses/i2c-parport @@ -12,18 +12,22 @@ meant as a replacement for the older, individual drivers: teletext adapters) It currently supports the following devices: - * Philips adapter - * home brew teletext adapter - * Velleman K8000 adapter - * ELV adapter - * Analog Devices evaluation boards (ADM1025, ADM1030, ADM1031, ADM1032) - * Barco LPT->DVI (K5800236) adapter + * (type=0) Philips adapter + * (type=1) home brew teletext adapter + * (type=2) Velleman K8000 adapter + * (type=3) ELV adapter + * (type=4) Analog Devices ADM1032 evaluation board + * (type=5) Analog Devices evaluation boards: ADM1025, ADM1030, ADM1031 + * (type=6) Barco LPT->DVI (K5800236) adapter These devices use different pinout configurations, so you have to tell the driver what you have, using the type module parameter. There is no way to autodetect the devices. Support for different pinout configurations can be easily added when needed. +Earlier kernels defaulted to type=0 (Philips). But now, if the type +parameter is missing, the driver will simply fail to initialize. + Building your own adapter ------------------------- diff --git a/Documentation/memory-barriers.txt b/Documentation/memory-barriers.txt index 92f0056d928..c61d8b876fd 100644 --- a/Documentation/memory-barriers.txt +++ b/Documentation/memory-barriers.txt @@ -1031,7 +1031,7 @@ conflict on any particular lock. LOCKS VS MEMORY ACCESSES ------------------------ -Consider the following: the system has a pair of spinlocks (N) and (Q), and +Consider the following: the system has a pair of spinlocks (M) and (Q), and three CPUs; then should the following sequence of events occur: CPU 1 CPU 2 @@ -1678,7 +1678,7 @@ CPU's caches by some other cache event: smp_wmb(); <A:modify v=2> <C:busy> <C:queue v=2> - p = &b; q = p; + p = &v; q = p; <D:request p> <B:modify p=&v> <D:commit p=&v> <D:read p> diff --git a/Documentation/networking/operstates.txt b/Documentation/networking/operstates.txt new file mode 100644 index 00000000000..4a21d9bb836 --- /dev/null +++ b/Documentation/networking/operstates.txt @@ -0,0 +1,161 @@ + +1. Introduction + +Linux distinguishes between administrative and operational state of an +interface. Admininstrative state is the result of "ip link set dev +<dev> up or down" and reflects whether the administrator wants to use +the device for traffic. + +However, an interface is not usable just because the admin enabled it +- ethernet requires to be plugged into the switch and, depending on +a site's networking policy and configuration, an 802.1X authentication +to be performed before user data can be transferred. Operational state +shows the ability of an interface to transmit this user data. + +Thanks to 802.1X, userspace must be granted the possibility to +influence operational state. To accommodate this, operational state is +split into two parts: Two flags that can be set by the driver only, and +a RFC2863 compatible state that is derived from these flags, a policy, +and changeable from userspace under certain rules. + + +2. Querying from userspace + +Both admin and operational state can be queried via the netlink +operation RTM_GETLINK. It is also possible to subscribe to RTMGRP_LINK +to be notified of updates. This is important for setting from userspace. + +These values contain interface state: + +ifinfomsg::if_flags & IFF_UP: + Interface is admin up +ifinfomsg::if_flags & IFF_RUNNING: + Interface is in RFC2863 operational state UP or UNKNOWN. This is for + backward compatibility, routing daemons, dhcp clients can use this + flag to determine whether they should use the interface. +ifinfomsg::if_flags & IFF_LOWER_UP: + Driver has signaled netif_carrier_on() +ifinfomsg::if_flags & IFF_DORMANT: + Driver has signaled netif_dormant_on() + +These interface flags can also be queried without netlink using the +SIOCGIFFLAGS ioctl. + +TLV IFLA_OPERSTATE + +contains RFC2863 state of the interface in numeric representation: + +IF_OPER_UNKNOWN (0): + Interface is in unknown state, neither driver nor userspace has set + operational state. Interface must be considered for user data as + setting operational state has not been implemented in every driver. +IF_OPER_NOTPRESENT (1): + Unused in current kernel (notpresent interfaces normally disappear), + just a numerical placeholder. +IF_OPER_DOWN (2): + Interface is unable to transfer data on L1, f.e. ethernet is not + plugged or interface is ADMIN down. +IF_OPER_LOWERLAYERDOWN (3): + Interfaces stacked on an interface that is IF_OPER_DOWN show this + state (f.e. VLAN). +IF_OPER_TESTING (4): + Unused in current kernel. +IF_OPER_DORMANT (5): + Interface is L1 up, but waiting for an external event, f.e. for a + protocol to establish. (802.1X) +IF_OPER_UP (6): + Interface is operational up and can be used. + +This TLV can also be queried via sysfs. + +TLV IFLA_LINKMODE + +contains link policy. This is needed for userspace interaction +described below. + +This TLV can also be queried via sysfs. + + +3. Kernel driver API + +Kernel drivers have access to two flags that map to IFF_LOWER_UP and +IFF_DORMANT. These flags can be set from everywhere, even from +interrupts. It is guaranteed that only the driver has write access, +however, if different layers of the driver manipulate the same flag, +the driver has to provide the synchronisation needed. + +__LINK_STATE_NOCARRIER, maps to !IFF_LOWER_UP: + +The driver uses netif_carrier_on() to clear and netif_carrier_off() to +set this flag. On netif_carrier_off(), the scheduler stops sending +packets. The name 'carrier' and the inversion are historical, think of +it as lower layer. + +netif_carrier_ok() can be used to query that bit. + +__LINK_STATE_DORMANT, maps to IFF_DORMANT: + +Set by the driver to express that the device cannot yet be used +because some driver controlled protocol establishment has to +complete. Corresponding functions are netif_dormant_on() to set the +flag, netif_dormant_off() to clear it and netif_dormant() to query. + +On device allocation, networking core sets the flags equivalent to +netif_carrier_ok() and !netif_dormant(). + + +Whenever the driver CHANGES one of these flags, a workqueue event is +scheduled to translate the flag combination to IFLA_OPERSTATE as +follows: + +!netif_carrier_ok(): + IF_OPER_LOWERLAYERDOWN if the interface is stacked, IF_OPER_DOWN + otherwise. Kernel can recognise stacked interfaces because their + ifindex != iflink. + +netif_carrier_ok() && netif_dormant(): + IF_OPER_DORMANT + +netif_carrier_ok() && !netif_dormant(): + IF_OPER_UP if userspace interaction is disabled. Otherwise + IF_OPER_DORMANT with the possibility for userspace to initiate the + IF_OPER_UP transition afterwards. + + +4. Setting from userspace + +Applications have to use the netlink interface to influence the +RFC2863 operational state of an interface. Setting IFLA_LINKMODE to 1 +via RTM_SETLINK instructs the kernel that an interface should go to +IF_OPER_DORMANT instead of IF_OPER_UP when the combination +netif_carrier_ok() && !netif_dormant() is set by the +driver. Afterwards, the userspace application can set IFLA_OPERSTATE +to IF_OPER_DORMANT or IF_OPER_UP as long as the driver does not set +netif_carrier_off() or netif_dormant_on(). Changes made by userspace +are multicasted on the netlink group RTMGRP_LINK. + +So basically a 802.1X supplicant interacts with the kernel like this: + +-subscribe to RTMGRP_LINK +-set IFLA_LINKMODE to 1 via RTM_SETLINK +-query RTM_GETLINK once to get initial state +-if initial flags are not (IFF_LOWER_UP && !IFF_DORMANT), wait until + netlink multicast signals this state +-do 802.1X, eventually abort if flags go down again +-send RTM_SETLINK to set operstate to IF_OPER_UP if authentication + succeeds, IF_OPER_DORMANT otherwise +-see how operstate and IFF_RUNNING is echoed via netlink multicast +-set interface back to IF_OPER_DORMANT if 802.1X reauthentication + fails +-restart if kernel changes IFF_LOWER_UP or IFF_DORMANT flag + +if supplicant goes down, bring back IFLA_LINKMODE to 0 and +IFLA_OPERSTATE to a sane value. + +A routing daemon or dhcp client just needs to care for IFF_RUNNING or +waiting for operstate to go IF_OPER_UP/IF_OPER_UNKNOWN before +considering the interface / querying a DHCP address. + + +For technical questions and/or comments please e-mail to Stefan Rompf +(stefan at loplof.de). diff --git a/Documentation/networking/xfrm_sync.txt b/Documentation/networking/xfrm_sync.txt new file mode 100644 index 00000000000..8be626f7c0b --- /dev/null +++ b/Documentation/networking/xfrm_sync.txt @@ -0,0 +1,166 @@ + +The sync patches work is based on initial patches from +Krisztian <hidden@balabit.hu> and others and additional patches +from Jamal <hadi@cyberus.ca>. + +The end goal for syncing is to be able to insert attributes + generate +events so that the an SA can be safely moved from one machine to another +for HA purposes. +The idea is to synchronize the SA so that the takeover machine can do +the processing of the SA as accurate as possible if it has access to it. + +We already have the ability to generate SA add/del/upd events. +These patches add ability to sync and have accurate lifetime byte (to +ensure proper decay of SAs) and replay counters to avoid replay attacks +with as minimal loss at failover time. +This way a backup stays as closely uptodate as an active member. + +Because the above items change for every packet the SA receives, +it is possible for a lot of the events to be generated. +For this reason, we also add a nagle-like algorithm to restrict +the events. i.e we are going to set thresholds to say "let me +know if the replay sequence threshold is reached or 10 secs have passed" +These thresholds are set system-wide via sysctls or can be updated +per SA. + +The identified items that need to be synchronized are: +- the lifetime byte counter +note that: lifetime time limit is not important if you assume the failover +machine is known ahead of time since the decay of the time countdown +is not driven by packet arrival. +- the replay sequence for both inbound and outbound + +1) Message Structure +---------------------- + +nlmsghdr:aevent_id:optional-TLVs. + +The netlink message types are: + +XFRM_MSG_NEWAE and XFRM_MSG_GETAE. + +A XFRM_MSG_GETAE does not have TLVs. +A XFRM_MSG_NEWAE will have at least two TLVs (as is +discussed further below). + +aevent_id structure looks like: + + struct xfrm_aevent_id { + struct xfrm_usersa_id sa_id; + __u32 flags; + }; + +xfrm_usersa_id in this message layout identifies the SA. + +flags are used to indicate different things. The possible +flags are: + XFRM_AE_RTHR=1, /* replay threshold*/ + XFRM_AE_RVAL=2, /* replay value */ + XFRM_AE_LVAL=4, /* lifetime value */ + XFRM_AE_ETHR=8, /* expiry timer threshold */ + XFRM_AE_CR=16, /* Event cause is replay update */ + XFRM_AE_CE=32, /* Event cause is timer expiry */ + XFRM_AE_CU=64, /* Event cause is policy update */ + +How these flags are used is dependent on the direction of the +message (kernel<->user) as well the cause (config, query or event). +This is described below in the different messages. + +The pid will be set appropriately in netlink to recognize direction +(0 to the kernel and pid = processid that created the event +when going from kernel to user space) + +A program needs to subscribe to multicast group XFRMNLGRP_AEVENTS +to get notified of these events. + +2) TLVS reflect the different parameters: +----------------------------------------- + +a) byte value (XFRMA_LTIME_VAL) +This TLV carries the running/current counter for byte lifetime since +last event. + +b)replay value (XFRMA_REPLAY_VAL) +This TLV carries the running/current counter for replay sequence since +last event. + +c)replay threshold (XFRMA_REPLAY_THRESH) +This TLV carries the threshold being used by the kernel to trigger events +when the replay sequence is exceeded. + +d) expiry timer (XFRMA_ETIMER_THRESH) +This is a timer value in milliseconds which is used as the nagle +value to rate limit the events. + +3) Default configurations for the parameters: +---------------------------------------------- + +By default these events should be turned off unless there is +at least one listener registered to listen to the multicast +group XFRMNLGRP_AEVENTS. + +Programs installing SAs will need to specify the two thresholds, however, +in order to not change existing applications such as racoon +we also provide default threshold values for these different parameters +in case they are not specified. + +the two sysctls/proc entries are: +a) /proc/sys/net/core/sysctl_xfrm_aevent_etime +used to provide default values for the XFRMA_ETIMER_THRESH in incremental +units of time of 100ms. The default is 10 (1 second) + +b) /proc/sys/net/core/sysctl_xfrm_aevent_rseqth +used to provide default values for XFRMA_REPLAY_THRESH parameter +in incremental packet count. The default is two packets. + +4) Message types +---------------- + +a) XFRM_MSG_GETAE issued by user-->kernel. +XFRM_MSG_GETAE does not carry any TLVs. +The response is a XFRM_MSG_NEWAE which is formatted based on what +XFRM_MSG_GETAE queried for. +The response will always have XFRMA_LTIME_VAL and XFRMA_REPLAY_VAL TLVs. +*if XFRM_AE_RTHR flag is set, then XFRMA_REPLAY_THRESH is also retrieved +*if XFRM_AE_ETHR flag is set, then XFRMA_ETIMER_THRESH is also retrieved + +b) XFRM_MSG_NEWAE is issued by either user space to configure +or kernel to announce events or respond to a XFRM_MSG_GETAE. + +i) user --> kernel to configure a specific SA. +any of the values or threshold parameters can be updated by passing the +appropriate TLV. +A response is issued back to the sender in user space to indicate success +or failure. +In the case of success, additionally an event with +XFRM_MSG_NEWAE is also issued to any listeners as described in iii). + +ii) kernel->user direction as a response to XFRM_MSG_GETAE +The response will always have XFRMA_LTIME_VAL and XFRMA_REPLAY_VAL TLVs. +The threshold TLVs will be included if explicitly requested in +the XFRM_MSG_GETAE message. + +iii) kernel->user to report as event if someone sets any values or +thresholds for an SA using XFRM_MSG_NEWAE (as described in #i above). +In such a case XFRM_AE_CU flag is set to inform the user that +the change happened as a result of an update. +The message will always have XFRMA_LTIME_VAL and XFRMA_REPLAY_VAL TLVs. + +iv) kernel->user to report event when replay threshold or a timeout +is exceeded. +In such a case either XFRM_AE_CR (replay exceeded) or XFRM_AE_CE (timeout +happened) is set to inform the user what happened. +Note the two flags are mutually exclusive. +The message will always have XFRMA_LTIME_VAL and XFRMA_REPLAY_VAL TLVs. + +Exceptions to threshold settings +-------------------------------- + +If you have an SA that is getting hit by traffic in bursts such that +there is a period where the timer threshold expires with no packets +seen, then an odd behavior is seen as follows: +The first packet arrival after a timer expiry will trigger a timeout +aevent; i.e we dont wait for a timeout period or a packet threshold +to be reached. This is done for simplicity and efficiency reasons. + +-JHS diff --git a/Documentation/pci.txt b/Documentation/pci.txt index 711210b38f5..66bbbf1d1ef 100644 --- a/Documentation/pci.txt +++ b/Documentation/pci.txt @@ -259,7 +259,17 @@ on the bus need to be capable of doing it, so this is something which needs to be handled by platform and generic code, not individual drivers. -8. Obsolete functions +8. Vendor and device identifications +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +For the future, let's avoid adding device ids to include/linux/pci_ids.h. + +PCI_VENDOR_ID_xxx for vendors, and a hex constant for device ids. + +Rationale: PCI_VENDOR_ID_xxx constants are re-used, but device ids are not. + Further, device ids are arbitrary hex numbers, normally used only in a + single location, the pci_device_id table. + +9. Obsolete functions ~~~~~~~~~~~~~~~~~~~~~ There are several functions which you might come across when trying to port an old driver to the new PCI interface. They are no longer present diff --git a/Documentation/power/video.txt b/Documentation/power/video.txt index d18a57d1a53..43a889f8f08 100644 --- a/Documentation/power/video.txt +++ b/Documentation/power/video.txt @@ -140,7 +140,7 @@ IBM TP T41p s3_bios (2), switch to X after resume IBM TP T42 s3_bios (2) IBM ThinkPad T42p (2373-GTG) s3_bios (2) IBM TP X20 ??? (*) -IBM TP X30 s3_bios (2) +IBM TP X30 s3_bios, s3_mode (4) IBM TP X31 / Type 2672-XXH none (1), use radeontool (http://fdd.com/software/radeon/) to turn off backlight. IBM TP X32 none (1), but backlight is on and video is trashed after long suspend. s3_bios,s3_mode (4) works too. Perhaps that gets better results? IBM Thinkpad X40 Type 2371-7JG s3_bios,s3_mode (4) diff --git a/Documentation/scsi/ChangeLog.megaraid b/Documentation/scsi/ChangeLog.megaraid index 09f6300eda4..c173806c91f 100644 --- a/Documentation/scsi/ChangeLog.megaraid +++ b/Documentation/scsi/ChangeLog.megaraid @@ -1,3 +1,28 @@ +Release Date : Mon Apr 11 12:27:22 EST 2006 - Seokmann Ju <sju@lsil.com> +Current Version : 2.20.4.8 (scsi module), 2.20.2.6 (cmm module) +Older Version : 2.20.4.7 (scsi module), 2.20.2.6 (cmm module) + +1. Fixed a bug in megaraid_reset_handler(). + Customer reported "Unable to handle kernel NULL pointer dereference + at virtual address 00000000" when system goes to reset condition + for some reason. It happened randomly. + Root Cause: in the megaraid_reset_handler(), there is possibility not + returning pending packets in the pend_list if there are multiple + pending packets. + Fix: Made the change in the driver so that it will return all packets + in the pend_list. + +2. Added change request. + As found in the following URL, rmb() only didn't help the + problem. I had to increase the loop counter to 0xFFFFFF. (6 F's) + http://marc.theaimsgroup.com/?l=linux-scsi&m=110971060502497&w=2 + + I attached a patch for your reference, too. + Could you check and get this fix in your driver? + + Best Regards, + Jun'ichi Nomura + Release Date : Fri Nov 11 12:27:22 EST 2005 - Seokmann Ju <sju@lsil.com> Current Version : 2.20.4.7 (scsi module), 2.20.2.6 (cmm module) Older Version : 2.20.4.6 (scsi module), 2.20.2.6 (cmm module) diff --git a/Documentation/serial/driver b/Documentation/serial/driver index 42ef9970bc8..88ad615dd33 100644 --- a/Documentation/serial/driver +++ b/Documentation/serial/driver @@ -3,14 +3,11 @@ -------------------- - $Id: driver,v 1.10 2002/07/22 15:27:30 rmk Exp $ - - This document is meant as a brief overview of some aspects of the new serial driver. It is not complete, any questions you have should be directed to <rmk@arm.linux.org.uk> -The reference implementation is contained within serial_amba.c. +The reference implementation is contained within amba_pl011.c. @@ -31,6 +28,11 @@ The serial core provides a few helper functions. This includes identifing the correct port structure (via uart_get_console) and decoding command line arguments (uart_parse_options). +There is also a helper function (uart_write_console) which performs a +character by character write, translating newlines to CRLF sequences. +Driver writers are recommended to use this function rather than implementing +their own version. + Locking ------- @@ -86,6 +88,7 @@ hardware. - TIOCM_DTR DTR signal. - TIOCM_OUT1 OUT1 signal. - TIOCM_OUT2 OUT2 signal. + - TIOCM_LOOP Set the port into loopback mode. If the appropriate bit is set, the signal should be driven active. If the bit is clear, the signal should be driven inactive. @@ -141,6 +144,10 @@ hardware. enable_ms(port) Enable the modem status interrupts. + This method may be called multiple times. Modem status + interrupts should be disabled when the shutdown method is + called. + Locking: port->lock taken. Interrupts: locally disabled. This call must not sleep @@ -160,6 +167,8 @@ hardware. state. Enable the port for reception. It should not activate RTS nor DTR; this will be done via a separate call to set_mctrl. + This method will only be called when the port is initially opened. + Locking: port_sem taken. Interrupts: globally disabled. @@ -169,6 +178,11 @@ hardware. RTS nor DTR; this will have already been done via a separate call to set_mctrl. + Drivers must not access port->info once this call has completed. + + This method will only be called when there are no more users of + this port. + Locking: port_sem taken. Interrupts: caller dependent. @@ -200,12 +214,13 @@ hardware. The interaction of the iflag bits is as follows (parity error given as an example): Parity error INPCK IGNPAR - None n/a n/a character received - Yes n/a 0 character discarded - Yes 0 1 character received, marked as + n/a 0 n/a character received, marked as + TTY_NORMAL + None 1 n/a character received, marked as TTY_NORMAL - Yes 1 1 character received, marked as + Yes 1 0 character received, marked as TTY_PARITY + Yes 1 1 character discarded Other flags may be used (eg, xon/xoff characters) if your hardware supports hardware "soft" flow control. diff --git a/Documentation/sound/alsa/Audiophile-Usb.txt b/Documentation/sound/alsa/Audiophile-Usb.txt index 4692c8e77dc..b535c2a198f 100644 --- a/Documentation/sound/alsa/Audiophile-Usb.txt +++ b/Documentation/sound/alsa/Audiophile-Usb.txt @@ -1,4 +1,4 @@ - Guide to using M-Audio Audiophile USB with ALSA and Jack v1.2 + Guide to using M-Audio Audiophile USB with ALSA and Jack v1.3 ======================================================== Thibault Le Meur <Thibault.LeMeur@supelec.fr> @@ -22,16 +22,16 @@ The device has 4 audio interfaces, and 2 MIDI ports: * Midi In (Mi) * Midi Out (Mo) -The internal DAC/ADC has the following caracteristics: +The internal DAC/ADC has the following characteristics: * sample depth of 16 or 24 bits * sample rate from 8kHz to 96kHz -* Two ports can't use different sample depths at the same time.Moreover, the +* Two ports can't use different sample depths at the same time. Moreover, the Audiophile USB documentation gives the following Warning: "Please exit any audio application running before switching between bit depths" Due to the USB 1.1 bandwidth limitation, a limited number of interfaces can be activated at the same time depending on the audio mode selected: - * 16-bit/48kHz ==> 4 channels in/ 4 channels out + * 16-bit/48kHz ==> 4 channels in/4 channels out - Ai+Ao+Di+Do * 24-bit/48kHz ==> 4 channels in/2 channels out, or 2 channels in/4 channels out @@ -41,8 +41,8 @@ activated at the same time depending on the audio mode selected: Important facts about the Digital interface: -------------------------------------------- - * The Do port additionnaly supports surround-encoded AC-3 and DTS passthrough, -though I haven't tested it under linux + * The Do port additionally supports surround-encoded AC-3 and DTS passthrough, +though I haven't tested it under Linux - Note that in this setup only the Do interface can be enabled * Apart from recording an audio digital stream, enabling the Di port is a way to synchronize the device to an external sample clock @@ -60,24 +60,23 @@ synchronization error (for instance sound played at an odd sample rate) The Audiophile USB MIDI ports will be automatically supported once the following modules have been loaded: * snd-usb-audio - * snd-seq * snd-seq-midi -No additionnal setting is required. +No additional setting is required. 2.2 - Audio ports ----------------- Audio functions of the Audiophile USB device are handled by the snd-usb-audio module. This module can work in a default mode (without any device-specific -parameter), or in an advanced mode with the device-specific parameter called +parameter), or in an "advanced" mode with the device-specific parameter called "device_setup". 2.2.1 - Default Alsa driver mode -The default behaviour of the snd-usb-audio driver is to parse the device +The default behavior of the snd-usb-audio driver is to parse the device capabilities at startup and enable all functions inside the device (including -all ports at any sample rates and any sample depths supported). This approach +all ports at any supported sample rates and sample depths). This approach has the advantage to let the driver easily switch from sample rates/depths automatically according to the need of the application claiming the device. @@ -114,9 +113,9 @@ gain). For people having this problem, the snd-usb-audio module has a new module parameter called "device_setup". -2.2.2.1 - Initializing the working mode of the Audiohile USB +2.2.2.1 - Initializing the working mode of the Audiophile USB -As far as the Audiohile USB device is concerned, this value let the user +As far as the Audiophile USB device is concerned, this value let the user specify: * the sample depth * the sample rate @@ -174,20 +173,20 @@ The parameter can be given: IMPORTANT NOTE WHEN SWITCHING CONFIGURATION: ------------------------------------------- - * You may need to _first_ intialize the module with the correct device_setup + * You may need to _first_ initialize the module with the correct device_setup parameter and _only_after_ turn on the Audiophile USB device * This is especially true when switching the sample depth: - - first trun off the device - - de-register the snd-usb-audio module - - change the device_setup parameter (by either manually reprobing the module - or changing modprobe.conf) + - first turn off the device + - de-register the snd-usb-audio module (modprobe -r) + - change the device_setup parameter by changing the device_setup + option in /etc/modprobe.conf - turn on the device 2.2.2.3 - Audiophile USB's device_setup structure If you want to understand the device_setup magic numbers for the Audiophile USB, you need some very basic understanding of binary computation. However, -this is not required to use the parameter and you may skip thi section. +this is not required to use the parameter and you may skip this section. The device_setup is one byte long and its structure is the following: @@ -231,11 +230,11 @@ Caution: 2.2.3 - USB implementation details for this device -You may safely skip this section if you're not interrested in driver +You may safely skip this section if you're not interested in driver development. -This section describes some internals aspect of the device and summarize the -data I got by usb-snooping the windows and linux drivers. +This section describes some internal aspects of the device and summarize the +data I got by usb-snooping the windows and Linux drivers. The M-Audio Audiophile USB has 7 USB Interfaces: a "USB interface": @@ -277,9 +276,9 @@ Here is a short description of the AltSettings capabilities: - 16-bit depth, 8-48kHz sample mode - Synch playback (Do), audio format type III IEC1937_AC-3 -In order to ensure a correct intialization of the device, the driver +In order to ensure a correct initialization of the device, the driver _must_know_ how the device will be used: - * if DTS is choosen, only Interface 2 with AltSet nb.6 must be + * if DTS is chosen, only Interface 2 with AltSet nb.6 must be registered * if 96KHz only AltSets nb.1 of each interface must be selected * if samples are using 24bits/48KHz then AltSet 2 must me used if @@ -290,7 +289,7 @@ _must_know_ how the device will be used: is not connected When device_setup is given as a parameter to the snd-usb-audio module, the -parse_audio_enpoint function uses a quirk called +parse_audio_endpoints function uses a quirk called "audiophile_skip_setting_quirk" in order to prevent AltSettings not corresponding to device_setup from being registered in the driver. @@ -317,9 +316,8 @@ However you may see the following warning message: using the "default" ALSA device. This is less efficient than it could be. Consider using a hardware device instead rather than using the plug layer." - 3.2 - Patching alsa to use direct pcm device -------------------------------------------- +-------------------------------------------- A patch for Jack by Andreas Steinmetz adds support for Big Endian devices. However it has not been included in the CVS tree. @@ -331,3 +329,32 @@ After having applied the patch you can run jackd with the following command line: % jackd -R -dalsa -Phw:1,0 -r48000 -p128 -n2 -D -Chw:1,1 +3.2 - Getting 2 input and/or output interfaces in Jack +------------------------------------------------------ + +As you can see, starting the Jack server this way will only enable 1 stereo +input (Di or Ai) and 1 stereo output (Ao or Do). + +This is due to the following restrictions: +* Jack can only open one capture device and one playback device at a time +* The Audiophile USB is seen as 2 (or three) Alsa devices: hw:1,0, hw:1,1 + (and optionally hw:1,2) +If you want to get Ai+Di and/or Ao+Do support with Jack, you would need to +combine the Alsa devices into one logical "complex" device. + +If you want to give it a try, I recommend reading the information from +this page: http://www.sound-man.co.uk/linuxaudio/ice1712multi.html +It is related to another device (ice1712) but can be adapted to suit +the Audiophile USB. + +Enabling multiple Audiophile USB interfaces for Jackd will certainly require: +* patching Jack with the previously mentioned "Big Endian" patch +* patching Jackd with the MMAP_COMPLEX patch (see the ice1712 page) +* patching the alsa-lib/src/pcm/pcm_multi.c file (see the ice1712 page) +* define a multi device (combination of hw:1,0 and hw:1,1) in your .asoundrc + file +* start jackd with this device + +I had no success in testing this for now, but this may be due to my OS +configuration. If you have any success with this kind of setup, please +drop me an email. diff --git a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl index 68eeebc17ff..1faf76383ba 100644 --- a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl +++ b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl @@ -1172,7 +1172,7 @@ } /* PCI IDs */ - static struct pci_device_id snd_mychip_ids[] = { + static struct pci_device_id snd_mychip_ids[] __devinitdata = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, .... @@ -1565,7 +1565,7 @@ <informalexample> <programlisting> <![CDATA[ - static struct pci_device_id snd_mychip_ids[] = { + static struct pci_device_id snd_mychip_ids[] __devinitdata = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, .... diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx new file mode 100644 index 00000000000..9c45f3df2e1 --- /dev/null +++ b/Documentation/spi/pxa2xx @@ -0,0 +1,234 @@ +PXA2xx SPI on SSP driver HOWTO +=================================================== +This a mini howto on the pxa2xx_spi driver. The driver turns a PXA2xx +synchronous serial port into a SPI master controller +(see Documentation/spi/spi_summary). The driver has the following features + +- Support for any PXA2xx SSP +- SSP PIO and SSP DMA data transfers. +- External and Internal (SSPFRM) chip selects. +- Per slave device (chip) configuration. +- Full suspend, freeze, resume support. + +The driver is built around a "spi_message" fifo serviced by workqueue and a +tasklet. The workqueue, "pump_messages", drives message fifo and the tasklet +(pump_transfer) is responsible for queuing SPI transactions and setting up and +launching the dma/interrupt driven transfers. + +Declaring PXA2xx Master Controllers +----------------------------------- +Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a +"platform device". The master configuration is passed to the driver via a table +found in include/asm-arm/arch-pxa/pxa2xx_spi.h: + +struct pxa2xx_spi_master { + enum pxa_ssp_type ssp_type; + u32 clock_enable; + u16 num_chipselect; + u8 enable_dma; +}; + +The "pxa2xx_spi_master.ssp_type" field must have a value between 1 and 3 and +informs the driver which features a particular SSP supports. + +The "pxa2xx_spi_master.clock_enable" field is used to enable/disable the +corresponding SSP peripheral block in the "Clock Enable Register (CKEN"). See +the "PXA2xx Developer Manual" section "Clocks and Power Management". + +The "pxa2xx_spi_master.num_chipselect" field is used to determine the number of +slave device (chips) attached to this SPI master. + +The "pxa2xx_spi_master.enable_dma" field informs the driver that SSP DMA should +be used. This caused the driver to acquire two DMA channels: rx_channel and +tx_channel. The rx_channel has a higher DMA service priority the tx_channel. +See the "PXA2xx Developer Manual" section "DMA Controller". + +NSSP MASTER SAMPLE +------------------ +Below is a sample configuration using the PXA255 NSSP. + +static struct resource pxa_spi_nssp_resources[] = { + [0] = { + .start = __PREG(SSCR0_P(2)), /* Start address of NSSP */ + .end = __PREG(SSCR0_P(2)) + 0x2c, /* Range of registers */ + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_NSSP, /* NSSP IRQ */ + .end = IRQ_NSSP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct pxa2xx_spi_master pxa_nssp_master_info = { + .ssp_type = PXA25x_NSSP, /* Type of SSP */ + .clock_enable = CKEN9_NSSP, /* NSSP Peripheral clock */ + .num_chipselect = 1, /* Matches the number of chips attached to NSSP */ + .enable_dma = 1, /* Enables NSSP DMA */ +}; + +static struct platform_device pxa_spi_nssp = { + .name = "pxa2xx-spi", /* MUST BE THIS VALUE, so device match driver */ + .id = 2, /* Bus number, MUST MATCH SSP number 1..n */ + .resource = pxa_spi_nssp_resources, + .num_resources = ARRAY_SIZE(pxa_spi_nssp_resources), + .dev = { + .platform_data = &pxa_nssp_master_info, /* Passed to driver */ + }, +}; + +static struct platform_device *devices[] __initdata = { + &pxa_spi_nssp, +}; + +static void __init board_init(void) +{ + (void)platform_add_device(devices, ARRAY_SIZE(devices)); +} + +Declaring Slave Devices +----------------------- +Typically each SPI slave (chip) is defined in the arch/.../mach-*/board-*.c +using the "spi_board_info" structure found in "linux/spi/spi.h". See +"Documentation/spi/spi_summary" for additional information. + +Each slave device attached to the PXA must provide slave specific configuration +information via the structure "pxa2xx_spi_chip" found in +"include/asm-arm/arch-pxa/pxa2xx_spi.h". The pxa2xx_spi master controller driver +will uses the configuration whenever the driver communicates with the slave +device. + +struct pxa2xx_spi_chip { + u8 tx_threshold; + u8 rx_threshold; + u8 dma_burst_size; + u32 timeout_microsecs; + u8 enable_loopback; + void (*cs_control)(u32 command); +}; + +The "pxa2xx_spi_chip.tx_threshold" and "pxa2xx_spi_chip.rx_threshold" fields are +used to configure the SSP hardware fifo. These fields are critical to the +performance of pxa2xx_spi driver and misconfiguration will result in rx +fifo overruns (especially in PIO mode transfers). Good default values are + + .tx_threshold = 12, + .rx_threshold = 4, + +The "pxa2xx_spi_chip.dma_burst_size" field is used to configure PXA2xx DMA +engine and is related the "spi_device.bits_per_word" field. Read and understand +the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers +to determine the correct value. An SSP configured for byte-wide transfers would +use a value of 8. + +The "pxa2xx_spi_chip.timeout_microsecs" fields is used to efficiently handle +trailing bytes in the SSP receiver fifo. The correct value for this field is +dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific +slave device. Please note the the PXA2xx SSP 1 does not support trailing byte +timeouts and must busy-wait any trailing bytes. + +The "pxa2xx_spi_chip.enable_loopback" field is used to place the SSP porting +into internal loopback mode. In this mode the SSP controller internally +connects the SSPTX pin the the SSPRX pin. This is useful for initial setup +testing. + +The "pxa2xx_spi_chip.cs_control" field is used to point to a board specific +function for asserting/deasserting a slave device chip select. If the field is +NULL, the pxa2xx_spi master controller driver assumes that the SSP port is +configured to use SSPFRM instead. + +NSSP SALVE SAMPLE +----------------- +The pxa2xx_spi_chip structure is passed to the pxa2xx_spi driver in the +"spi_board_info.controller_data" field. Below is a sample configuration using +the PXA255 NSSP. + +/* Chip Select control for the CS8415A SPI slave device */ +static void cs8415a_cs_control(u32 command) +{ + if (command & PXA2XX_CS_ASSERT) + GPCR(2) = GPIO_bit(2); + else + GPSR(2) = GPIO_bit(2); +} + +/* Chip Select control for the CS8405A SPI slave device */ +static void cs8405a_cs_control(u32 command) +{ + if (command & PXA2XX_CS_ASSERT) + GPCR(3) = GPIO_bit(3); + else + GPSR(3) = GPIO_bit(3); +} + +static struct pxa2xx_spi_chip cs8415a_chip_info = { + .tx_threshold = 12, /* SSP hardward FIFO threshold */ + .rx_threshold = 4, /* SSP hardward FIFO threshold */ + .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */ + .timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */ + .cs_control = cs8415a_cs_control, /* Use external chip select */ +}; + +static struct pxa2xx_spi_chip cs8405a_chip_info = { + .tx_threshold = 12, /* SSP hardward FIFO threshold */ + .rx_threshold = 4, /* SSP hardward FIFO threshold */ + .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */ + .timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */ + .cs_control = cs8405a_cs_control, /* Use external chip select */ +}; + +static struct spi_board_info streetracer_spi_board_info[] __initdata = { + { + .modalias = "cs8415a", /* Name of spi_driver for this device */ + .max_speed_hz = 3686400, /* Run SSP as fast a possbile */ + .bus_num = 2, /* Framework bus number */ + .chip_select = 0, /* Framework chip select */ + .platform_data = NULL; /* No spi_driver specific config */ + .controller_data = &cs8415a_chip_info, /* Master chip config */ + .irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */ + }, + { + .modalias = "cs8405a", /* Name of spi_driver for this device */ + .max_speed_hz = 3686400, /* Run SSP as fast a possbile */ + .bus_num = 2, /* Framework bus number */ + .chip_select = 1, /* Framework chip select */ + .controller_data = &cs8405a_chip_info, /* Master chip config */ + .irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */ + }, +}; + +static void __init streetracer_init(void) +{ + spi_register_board_info(streetracer_spi_board_info, + ARRAY_SIZE(streetracer_spi_board_info)); +} + + +DMA and PIO I/O Support +----------------------- +The pxa2xx_spi driver support both DMA and interrupt driven PIO message +transfers. The driver defaults to PIO mode and DMA transfers must enabled by +setting the "enable_dma" flag in the "pxa2xx_spi_master" structure and and +ensuring that the "pxa2xx_spi_chip.dma_burst_size" field is non-zero. The DMA +mode support both coherent and stream based DMA mappings. + +The following logic is used to determine the type of I/O to be used on +a per "spi_transfer" basis: + +if !enable_dma or dma_burst_size == 0 then + always use PIO transfers + +if spi_message.is_dma_mapped and rx_dma_buf != 0 and tx_dma_buf != 0 then + use coherent DMA mode + +if rx_buf and tx_buf are aligned on 8 byte boundary then + use streaming DMA mode + +otherwise + use PIO transfer + +THANKS TO +--------- + +David Brownell and others for mentoring the development of this driver. + diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary index a5ffba33a35..068732d3227 100644 --- a/Documentation/spi/spi-summary +++ b/Documentation/spi/spi-summary @@ -414,7 +414,33 @@ to get the driver-private data allocated for that device. The driver will initialize the fields of that spi_master, including the bus number (maybe the same as the platform device ID) and three methods used to interact with the SPI core and SPI protocol drivers. It will -also initialize its own internal state. +also initialize its own internal state. (See below about bus numbering +and those methods.) + +After you initialize the spi_master, then use spi_register_master() to +publish it to the rest of the system. At that time, device nodes for +the controller and any predeclared spi devices will be made available, +and the driver model core will take care of binding them to drivers. + +If you need to remove your SPI controller driver, spi_unregister_master() +will reverse the effect of spi_register_master(). + + +BUS NUMBERING + +Bus numbering is important, since that's how Linux identifies a given +SPI bus (shared SCK, MOSI, MISO). Valid bus numbers start at zero. On +SOC systems, the bus numbers should match the numbers defined by the chip +manufacturer. For example, hardware controller SPI2 would be bus number 2, +and spi_board_info for devices connected to it would use that number. + +If you don't have such hardware-assigned bus number, and for some reason +you can't just assign them, then provide a negative bus number. That will +then be replaced by a dynamically assigned number. You'd then need to treat +this as a non-static configuration (see above). + + +SPI MASTER METHODS master->setup(struct spi_device *spi) This sets up the device clock rate, SPI mode, and word sizes. @@ -431,6 +457,9 @@ also initialize its own internal state. state it dynamically associates with that device. If you do that, be sure to provide the cleanup() method to free that state. + +SPI MESSAGE QUEUE + The bulk of the driver will be managing the I/O queue fed by transfer(). That queue could be purely conceptual. For example, a driver used only @@ -440,6 +469,9 @@ But the queue will probably be very real, using message->queue, PIO, often DMA (especially if the root filesystem is in SPI flash), and execution contexts like IRQ handlers, tasklets, or workqueues (such as keventd). Your driver can be as fancy, or as simple, as you need. +Such a transfer() method would normally just add the message to a +queue, and then start some asynchronous transfer engine (unless it's +already running). THANKS TO diff --git a/Documentation/vm/hugetlbpage.txt b/Documentation/vm/hugetlbpage.txt index 2803f63c1a2..687104bfd09 100644 --- a/Documentation/vm/hugetlbpage.txt +++ b/Documentation/vm/hugetlbpage.txt @@ -32,7 +32,16 @@ The output of "cat /proc/meminfo" will have lines like: ..... HugePages_Total: xxx HugePages_Free: yyy -Hugepagesize: zzz KB +HugePages_Rsvd: www +Hugepagesize: zzz kB + +where: +HugePages_Total is the size of the pool of hugepages. +HugePages_Free is the number of hugepages in the pool that are not yet +allocated. +HugePages_Rsvd is short for "reserved," and is the number of hugepages +for which a commitment to allocate from the pool has been made, but no +allocation has yet been made. It's vaguely analogous to overcommit. /proc/filesystems should also show a filesystem of type "hugetlbfs" configured in the kernel. diff --git a/Documentation/watchdog/watchdog-api.txt b/Documentation/watchdog/watchdog-api.txt index c5beb548cfc..21ed5117366 100644 --- a/Documentation/watchdog/watchdog-api.txt +++ b/Documentation/watchdog/watchdog-api.txt @@ -36,6 +36,9 @@ timeout or margin. The simplest way to ping the watchdog is to write some data to the device. So a very simple watchdog daemon would look like this: +#include <stdlib.h> +#include <fcntl.h> + int main(int argc, const char *argv[]) { int fd=open("/dev/watchdog",O_WRONLY); if (fd==-1) { |