3 files changed, 81 insertions, 2 deletions
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
index af90b00100f..8dc48214f0b 100644
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -18,6 +18,10 @@ config BOARD_ATSTK1004
 	bool "ATSTK1004"
 	select CPU_AT32AP7002
 
+config BOARD_ATSTK1006
+	bool "ATSTK1006"
+	select CPU_AT32AP7000
+
 endchoice
 
 
diff --git a/arch/avr32/boards/atstk1000/Makefile b/arch/avr32/boards/atstk1000/Makefile
index beead86462e..edecee03742 100644
--- a/arch/avr32/boards/atstk1000/Makefile
+++ b/arch/avr32/boards/atstk1000/Makefile
@@ -2,3 +2,4 @@ obj-y				+= setup.o flash.o
 obj-$(CONFIG_BOARD_ATSTK1002)	+= atstk1002.o
 obj-$(CONFIG_BOARD_ATSTK1003)	+= atstk1003.o
 obj-$(CONFIG_BOARD_ATSTK1004)	+= atstk1004.o
+obj-$(CONFIG_BOARD_ATSTK1006)	+= atstk1002.o
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index 000eb4220a1..5bfaf4d87b3 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -1,7 +1,7 @@
 /*
- * ATSTK1002 daughterboard-specific init code
+ * ATSTK1002/ATSTK1006 daughterboard-specific init code
  *
- * Copyright (C) 2005-2006 Atmel Corporation
+ * Copyright (C) 2005-2007 Atmel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -29,6 +29,74 @@
 #include "atstk1000.h"
 
 
+/*
+ * The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both
+ * have the AT32AP7000 chip on board; the difference is that the
+ * STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on
+ * the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has
+ * none.)
+ *
+ * The RAM difference is handled by the boot loader, so the only
+ * difference we end up handling here is the NAND flash.
+ */
+#ifdef CONFIG_BOARD_ATSTK1006
+#include <linux/mtd/partitions.h>
+#include <asm/arch/smc.h>
+
+static struct smc_timing nand_timing __initdata = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 10,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 10,
+
+	.ncs_read_pulse		= 30,
+	.nrd_pulse		= 15,
+	.ncs_write_pulse	= 30,
+	.nwe_pulse		= 15,
+
+	.read_cycle		= 30,
+	.write_cycle		= 30,
+
+	.ncs_read_recover	= 0,
+	.nrd_recover		= 15,
+	.ncs_write_recover	= 0,
+	/* WE# high -> RE# low min 60 ns */
+	.nwe_recover		= 50,
+};
+
+static struct smc_config nand_config __initdata = {
+	.bus_width		= 1,
+	.nrd_controlled		= 1,
+	.nwe_controlled		= 1,
+	.nwait_mode		= 0,
+	.byte_write		= 0,
+	.tdf_cycles		= 2,
+	.tdf_mode		= 0,
+};
+
+static struct mtd_partition nand_partitions[] = {
+	{
+		.name		= "main",
+		.offset		= 0x00000000,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_part_info(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(nand_partitions);
+	return nand_partitions;
+}
+
+struct atmel_nand_data atstk1006_nand_data __initdata = {
+	.cle		= 21,
+	.ale		= 22,
+	.rdy_pin	= GPIO_PIN_PB(30),
+	.enable_pin	= GPIO_PIN_PB(29),
+	.partition_info	= nand_part_info,
+};
+#endif
+
 struct eth_addr {
 	u8 addr[6];
 };
@@ -212,6 +280,12 @@ static int __init atstk1002_init(void)
 
 	at32_add_system_devices();
 
+#ifdef CONFIG_BOARD_ATSTK1006
+	smc_set_timing(&nand_config, &nand_timing);
+	smc_set_configuration(3, &nand_config);
+	at32_add_device_nand(0, &atstk1006_nand_data);
+#endif
+
 #ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
 	at32_add_device_usart(1);
 #else