aboutsummaryrefslogtreecommitdiff
path: root/drivers/scsi/53c7xx.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/scsi/53c7xx.c')
-rw-r--r--drivers/scsi/53c7xx.c6102
1 files changed, 0 insertions, 6102 deletions
diff --git a/drivers/scsi/53c7xx.c b/drivers/scsi/53c7xx.c
deleted file mode 100644
index 93b41f45638..00000000000
--- a/drivers/scsi/53c7xx.c
+++ /dev/null
@@ -1,6102 +0,0 @@
-/*
- * 53c710 driver. Modified from Drew Eckhardts driver
- * for 53c810 by Richard Hirst [richard@sleepie.demon.co.uk]
- * Check out PERM_OPTIONS and EXPECTED_CLOCK, which may be defined in the
- * relevant machine specific file (eg. mvme16x.[ch], amiga7xx.[ch]).
- * There are also currently some defines at the top of 53c7xx.scr.
- * The chip type is #defined in script_asm.pl, as well as the Makefile.
- * Host scsi ID expected to be 7 - see NCR53c7x0_init().
- *
- * I have removed the PCI code and some of the 53c8xx specific code -
- * simply to make this file smaller and easier to manage.
- *
- * MVME16x issues:
- * Problems trying to read any chip registers in NCR53c7x0_init(), as they
- * may never have been set by 16xBug (eg. If kernel has come in over tftp).
- */
-
-/*
- * Adapted for Linux/m68k Amiga platforms for the A4000T/A4091 and
- * WarpEngine SCSI controllers.
- * By Alan Hourihane <alanh@fairlite.demon.co.uk>
- * Thanks to Richard Hirst for making it possible with the MVME additions
- */
-
-/*
- * 53c710 rev 0 doesn't support add with carry. Rev 1 and 2 does. To
- * overcome this problem you can define FORCE_DSA_ALIGNMENT, which ensures
- * that the DSA address is always xxxxxx00. If disconnection is not allowed,
- * then the script only ever tries to add small (< 256) positive offsets to
- * DSA, so lack of carry isn't a problem. FORCE_DSA_ALIGNMENT can, of course,
- * be defined for all chip revisions at a small cost in memory usage.
- */
-
-#define FORCE_DSA_ALIGNMENT
-
-/*
- * Selection timer does not always work on the 53c710, depending on the
- * timing at the last disconnect, if this is a problem for you, try
- * using validids as detailed below.
- *
- * Options for the NCR7xx driver
- *
- * noasync:0 - disables sync and asynchronous negotiation
- * nosync:0 - disables synchronous negotiation (does async)
- * nodisconnect:0 - disables disconnection
- * validids:0x?? - Bitmask field that disallows certain ID's.
- * - e.g. 0x03 allows ID 0,1
- * - 0x1F allows ID 0,1,2,3,4
- * opthi:n - replace top word of options with 'n'
- * optlo:n - replace bottom word of options with 'n'
- * - ALWAYS SPECIFY opthi THEN optlo <<<<<<<<<<
- */
-
-/*
- * PERM_OPTIONS are driver options which will be enabled for all NCR boards
- * in the system at driver initialization time.
- *
- * Don't THINK about touching these in PERM_OPTIONS :
- * OPTION_MEMORY_MAPPED
- * 680x0 doesn't have an IO map!
- *
- * OPTION_DEBUG_TEST1
- * Test 1 does bus mastering and interrupt tests, which will help weed
- * out brain damaged main boards.
- *
- * Other PERM_OPTIONS settings are listed below. Note the actual options
- * required are set in the relevant file (mvme16x.c, amiga7xx.c, etc):
- *
- * OPTION_NO_ASYNC
- * Don't negotiate for asynchronous transfers on the first command
- * when OPTION_ALWAYS_SYNCHRONOUS is set. Useful for dain bramaged
- * devices which do something bad rather than sending a MESSAGE
- * REJECT back to us like they should if they can't cope.
- *
- * OPTION_SYNCHRONOUS
- * Enable support for synchronous transfers. Target negotiated
- * synchronous transfers will be responded to. To initiate
- * a synchronous transfer request, call
- *
- * request_synchronous (hostno, target)
- *
- * from within KGDB.
- *
- * OPTION_ALWAYS_SYNCHRONOUS
- * Negotiate for synchronous transfers with every target after
- * driver initialization or a SCSI bus reset. This is a bit dangerous,
- * since there are some dain bramaged SCSI devices which will accept
- * SDTR messages but keep talking asynchronously.
- *
- * OPTION_DISCONNECT
- * Enable support for disconnect/reconnect. To change the
- * default setting on a given host adapter, call
- *
- * request_disconnect (hostno, allow)
- *
- * where allow is non-zero to allow, 0 to disallow.
- *
- * If you really want to run 10MHz FAST SCSI-II transfers, you should
- * know that the NCR driver currently ignores parity information. Most
- * systems do 5MHz SCSI fine. I've seen a lot that have problems faster
- * than 8MHz. To play it safe, we only request 5MHz transfers.
- *
- * If you'd rather get 10MHz transfers, edit sdtr_message and change
- * the fourth byte from 50 to 25.
- */
-
-/*
- * Sponsored by
- * iX Multiuser Multitasking Magazine
- * Hannover, Germany
- * hm@ix.de
- *
- * Copyright 1993, 1994, 1995 Drew Eckhardt
- * Visionary Computing
- * (Unix and Linux consulting and custom programming)
- * drew@PoohSticks.ORG
- * +1 (303) 786-7975
- *
- * TolerANT and SCSI SCRIPTS are registered trademarks of NCR Corporation.
- *
- * For more information, please consult
- *
- * NCR53C810
- * SCSI I/O Processor
- * Programmer's Guide
- *
- * NCR 53C810
- * PCI-SCSI I/O Processor
- * Data Manual
- *
- * NCR 53C810/53C820
- * PCI-SCSI I/O Processor Design In Guide
- *
- * For literature on Symbios Logic Inc. formerly NCR, SCSI,
- * and Communication products please call (800) 334-5454 or
- * (719) 536-3300.
- *
- * PCI BIOS Specification Revision
- * PCI Local Bus Specification
- * PCI System Design Guide
- *
- * PCI Special Interest Group
- * M/S HF3-15A
- * 5200 N.E. Elam Young Parkway
- * Hillsboro, Oregon 97124-6497
- * +1 (503) 696-2000
- * +1 (800) 433-5177
- */
-
-/*
- * Design issues :
- * The cumulative latency needed to propagate a read/write request
- * through the file system, buffer cache, driver stacks, SCSI host, and
- * SCSI device is ultimately the limiting factor in throughput once we
- * have a sufficiently fast host adapter.
- *
- * So, to maximize performance we want to keep the ratio of latency to data
- * transfer time to a minimum by
- * 1. Minimizing the total number of commands sent (typical command latency
- * including drive and bus mastering host overhead is as high as 4.5ms)
- * to transfer a given amount of data.
- *
- * This is accomplished by placing no arbitrary limit on the number
- * of scatter/gather buffers supported, since we can transfer 1K
- * per scatter/gather buffer without Eric's cluster patches,
- * 4K with.
- *
- * 2. Minimizing the number of fatal interrupts serviced, since
- * fatal interrupts halt the SCSI I/O processor. Basically,
- * this means offloading the practical maximum amount of processing
- * to the SCSI chip.
- *
- * On the NCR53c810/820/720, this is accomplished by using
- * interrupt-on-the-fly signals when commands complete,
- * and only handling fatal errors and SDTR / WDTR messages
- * in the host code.
- *
- * On the NCR53c710, interrupts are generated as on the NCR53c8x0,
- * only the lack of a interrupt-on-the-fly facility complicates
- * things. Also, SCSI ID registers and commands are
- * bit fielded rather than binary encoded.
- *
- * On the NCR53c700 and NCR53c700-66, operations that are done via
- * indirect, table mode on the more advanced chips must be
- * replaced by calls through a jump table which
- * acts as a surrogate for the DSA. Unfortunately, this
- * will mean that we must service an interrupt for each
- * disconnect/reconnect.
- *
- * 3. Eliminating latency by pipelining operations at the different levels.
- *
- * This driver allows a configurable number of commands to be enqueued
- * for each target/lun combination (experimentally, I have discovered
- * that two seems to work best) and will ultimately allow for
- * SCSI-II tagged queuing.
- *
- *
- * Architecture :
- * This driver is built around a Linux queue of commands waiting to
- * be executed, and a shared Linux/NCR array of commands to start. Commands
- * are transferred to the array by the run_process_issue_queue() function
- * which is called whenever a command completes.
- *
- * As commands are completed, the interrupt routine is triggered,
- * looks for commands in the linked list of completed commands with
- * valid status, removes these commands from a list of running commands,
- * calls the done routine, and flags their target/luns as not busy.
- *
- * Due to limitations in the intelligence of the NCR chips, certain
- * concessions are made. In many cases, it is easier to dynamically
- * generate/fix-up code rather than calculate on the NCR at run time.
- * So, code is generated or fixed up for
- *
- * - Handling data transfers, using a variable number of MOVE instructions
- * interspersed with CALL MSG_IN, WHEN MSGIN instructions.
- *
- * The DATAIN and DATAOUT routines are separate, so that an incorrect
- * direction can be trapped, and space isn't wasted.
- *
- * It may turn out that we're better off using some sort
- * of table indirect instruction in a loop with a variable
- * sized table on the NCR53c710 and newer chips.
- *
- * - Checking for reselection (NCR53c710 and better)
- *
- * - Handling the details of SCSI context switches (NCR53c710 and better),
- * such as reprogramming appropriate synchronous parameters,
- * removing the dsa structure from the NCR's queue of outstanding
- * commands, etc.
- *
- */
-
-#include <linux/module.h>
-
-
-#include <linux/types.h>
-#include <asm/setup.h>
-#include <asm/dma.h>
-#include <asm/io.h>
-#include <asm/system.h>
-#include <linux/delay.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/vmalloc.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/time.h>
-#include <linux/blkdev.h>
-#include <linux/spinlock.h>
-#include <linux/interrupt.h>
-#include <asm/pgtable.h>
-
-#ifdef CONFIG_AMIGA
-#include <asm/amigahw.h>
-#include <asm/amigaints.h>
-#include <asm/irq.h>
-
-#define BIG_ENDIAN
-#define NO_IO_SPACE
-#endif
-
-#ifdef CONFIG_MVME16x
-#include <asm/mvme16xhw.h>
-
-#define BIG_ENDIAN
-#define NO_IO_SPACE
-#define VALID_IDS
-#endif
-
-#ifdef CONFIG_BVME6000
-#include <asm/bvme6000hw.h>
-
-#define BIG_ENDIAN
-#define NO_IO_SPACE
-#define VALID_IDS
-#endif
-
-#include "scsi.h"
-#include <scsi/scsi_dbg.h>
-#include <scsi/scsi_host.h>
-#include <scsi/scsi_transport_spi.h>
-#include "53c7xx.h"
-#include <linux/stat.h>
-#include <linux/stddef.h>
-
-#ifdef NO_IO_SPACE
-/*
- * The following make the definitions in 53c7xx.h (write8, etc) smaller,
- * we don't have separate i/o space anyway.
- */
-#undef inb
-#undef outb
-#undef inw
-#undef outw
-#undef inl
-#undef outl
-#define inb(x) 1
-#define inw(x) 1
-#define inl(x) 1
-#define outb(x,y) 1
-#define outw(x,y) 1
-#define outl(x,y) 1
-#endif
-
-static int check_address (unsigned long addr, int size);
-static void dump_events (struct Scsi_Host *host, int count);
-static Scsi_Cmnd * return_outstanding_commands (struct Scsi_Host *host,
- int free, int issue);
-static void hard_reset (struct Scsi_Host *host);
-static void ncr_scsi_reset (struct Scsi_Host *host);
-static void print_lots (struct Scsi_Host *host);
-static void set_synchronous (struct Scsi_Host *host, int target, int sxfer,
- int scntl3, int now_connected);
-static int datapath_residual (struct Scsi_Host *host);
-static const char * sbcl_to_phase (int sbcl);
-static void print_progress (Scsi_Cmnd *cmd);
-static void print_queues (struct Scsi_Host *host);
-static void process_issue_queue (unsigned long flags);
-static int shutdown (struct Scsi_Host *host);
-static void abnormal_finished (struct NCR53c7x0_cmd *cmd, int result);
-static int disable (struct Scsi_Host *host);
-static int NCR53c7xx_run_tests (struct Scsi_Host *host);
-static irqreturn_t NCR53c7x0_intr(int irq, void *dev_id);
-static void NCR53c7x0_intfly (struct Scsi_Host *host);
-static int ncr_halt (struct Scsi_Host *host);
-static void intr_phase_mismatch (struct Scsi_Host *host, struct NCR53c7x0_cmd
- *cmd);
-static void intr_dma (struct Scsi_Host *host, struct NCR53c7x0_cmd *cmd);
-static void print_dsa (struct Scsi_Host *host, u32 *dsa,
- const char *prefix);
-static int print_insn (struct Scsi_Host *host, const u32 *insn,
- const char *prefix, int kernel);
-
-static void NCR53c7xx_dsa_fixup (struct NCR53c7x0_cmd *cmd);
-static void NCR53c7x0_init_fixup (struct Scsi_Host *host);
-static int NCR53c7x0_dstat_sir_intr (struct Scsi_Host *host, struct
- NCR53c7x0_cmd *cmd);
-static void NCR53c7x0_soft_reset (struct Scsi_Host *host);
-
-/* Size of event list (per host adapter) */
-static int track_events = 0;
-static struct Scsi_Host *first_host = NULL; /* Head of list of NCR boards */
-static struct scsi_host_template *the_template = NULL;
-
-/* NCR53c710 script handling code */
-
-#include "53c7xx_d.h"
-#ifdef A_int_debug_sync
-#define DEBUG_SYNC_INTR A_int_debug_sync
-#endif
-int NCR53c7xx_script_len = sizeof (SCRIPT);
-int NCR53c7xx_dsa_len = A_dsa_end + Ent_dsa_zero - Ent_dsa_code_template;
-#ifdef FORCE_DSA_ALIGNMENT
-int CmdPageStart = (0 - Ent_dsa_zero - sizeof(struct NCR53c7x0_cmd)) & 0xff;
-#endif
-
-static char *setup_strings[] =
- {"","","","","","","",""};
-
-#define MAX_SETUP_STRINGS ARRAY_SIZE(setup_strings)
-#define SETUP_BUFFER_SIZE 200
-static char setup_buffer[SETUP_BUFFER_SIZE];
-static char setup_used[MAX_SETUP_STRINGS];
-
-void ncr53c7xx_setup (char *str, int *ints)
-{
- int i;
- char *p1, *p2;
-
- p1 = setup_buffer;
- *p1 = '\0';
- if (str)
- strncpy(p1, str, SETUP_BUFFER_SIZE - strlen(setup_buffer));
- setup_buffer[SETUP_BUFFER_SIZE - 1] = '\0';
- p1 = setup_buffer;
- i = 0;
- while (*p1 && (i < MAX_SETUP_STRINGS)) {
- p2 = strchr(p1, ',');
- if (p2) {
- *p2 = '\0';
- if (p1 != p2)
- setup_strings[i] = p1;
- p1 = p2 + 1;
- i++;
- }
- else {
- setup_strings[i] = p1;
- break;
- }
- }
- for (i=0; i<MAX_SETUP_STRINGS; i++)
- setup_used[i] = 0;
-}
-
-
-/* check_setup_strings() returns index if key found, 0 if not
- */
-
-static int check_setup_strings(char *key, int *flags, int *val, char *buf)
-{
-int x;
-char *cp;
-
- for (x=0; x<MAX_SETUP_STRINGS; x++) {
- if (setup_used[x])
- continue;
- if (!strncmp(setup_strings[x], key, strlen(key)))
- break;
- if (!strncmp(setup_strings[x], "next", strlen("next")))
- return 0;
- }
- if (x == MAX_SETUP_STRINGS)
- return 0;
- setup_used[x] = 1;
- cp = setup_strings[x] + strlen(key);
- *val = -1;
- if (*cp != ':')
- return ++x;
- cp++;
- if ((*cp >= '0') && (*cp <= '9')) {
- *val = simple_strtoul(cp,NULL,0);
- }
- return ++x;
-}
-
-
-
-/*
- * KNOWN BUGS :
- * - There is some sort of conflict when the PPP driver is compiled with
- * support for 16 channels?
- *
- * - On systems which predate the 1.3.x initialization order change,
- * the NCR driver will cause Cannot get free page messages to appear.
- * These are harmless, but I don't know of an easy way to avoid them.
- *
- * - With OPTION_DISCONNECT, on two systems under unknown circumstances,
- * we get a PHASE MISMATCH with DSA set to zero (suggests that we
- * are occurring somewhere in the reselection code) where
- * DSP=some value DCMD|DBC=same value.
- *
- * Closer inspection suggests that we may be trying to execute
- * some portion of the DSA?
- * scsi0 : handling residual transfer (+ 0 bytes from DMA FIFO)
- * scsi0 : handling residual transfer (+ 0 bytes from DMA FIFO)
- * scsi0 : no current command : unexpected phase MSGIN.
- * DSP=0x1c46cc, DCMD|DBC=0x1c46ac, DSA=0x0
- * DSPS=0x0, TEMP=0x1c3e70, DMODE=0x80
- * scsi0 : DSP->
- * 001c46cc : 0x001c46cc 0x00000000
- * 001c46d4 : 0x001c5ea0 0x000011f8
- *
- * Changed the print code in the phase_mismatch handler so
- * that we call print_lots to try to diagnose this.
- *
- */
-
-/*
- * Possible future direction of architecture for max performance :
- *
- * We're using a single start array for the NCR chip. This is
- * sub-optimal, because we cannot add a command which would conflict with
- * an executing command to this start queue, and therefore must insert the
- * next command for a given I/T/L combination after the first has completed;
- * incurring our interrupt latency between SCSI commands.
- *
- * To allow further pipelining of the NCR and host CPU operation, we want
- * to set things up so that immediately on termination of a command destined
- * for a given LUN, we get that LUN busy again.
- *
- * To do this, we need to add a 32 bit pointer to which is jumped to
- * on completion of a command. If no new command is available, this
- * would point to the usual DSA issue queue select routine.
- *
- * If one were, it would point to a per-NCR53c7x0_cmd select routine
- * which starts execution immediately, inserting the command at the head
- * of the start queue if the NCR chip is selected or reselected.
- *
- * We would change so that we keep a list of outstanding commands
- * for each unit, rather than a single running_list. We'd insert
- * a new command into the right running list; if the NCR didn't
- * have something running for that yet, we'd put it in the
- * start queue as well. Some magic needs to happen to handle the
- * race condition between the first command terminating before the
- * new one is written.
- *
- * Potential for profiling :
- * Call do_gettimeofday(struct timeval *tv) to get 800ns resolution.
- */
-
-
-/*
- * TODO :
- * 1. To support WIDE transfers, not much needs to happen. We
- * should do CHMOVE instructions instead of MOVEs when
- * we have scatter/gather segments of uneven length. When
- * we do this, we need to handle the case where we disconnect
- * between segments.
- *
- * 2. Currently, when Icky things happen we do a FATAL(). Instead,
- * we want to do an integrity check on the parts of the NCR hostdata
- * structure which were initialized at boot time; FATAL() if that
- * fails, and otherwise try to recover. Keep track of how many
- * times this has happened within a single SCSI command; if it
- * gets excessive, then FATAL().
- *
- * 3. Parity checking is currently disabled, and a few things should
- * happen here now that we support synchronous SCSI transfers :
- * 1. On soft-reset, we shoould set the EPC (Enable Parity Checking)
- * and AAP (Assert SATN/ on parity error) bits in SCNTL0.
- *
- * 2. We should enable the parity interrupt in the SIEN0 register.
- *
- * 3. intr_phase_mismatch() needs to believe that message out is
- * always an "acceptable" phase to have a mismatch in. If
- * the old phase was MSG_IN, we should send a MESSAGE PARITY
- * error. If the old phase was something else, we should send
- * a INITIATOR_DETECTED_ERROR message. Note that this could
- * cause a RESTORE POINTERS message; so we should handle that
- * correctly first. Instead, we should probably do an
- * initiator_abort.
- *
- * 4. MPEE bit of CTEST4 should be set so we get interrupted if
- * we detect an error.
- *
- *
- * 5. The initial code has been tested on the NCR53c810. I don't
- * have access to NCR53c700, 700-66 (Forex boards), NCR53c710
- * (NCR Pentium systems), NCR53c720, NCR53c820, or NCR53c825 boards to
- * finish development on those platforms.
- *
- * NCR53c820/825/720 - need to add wide transfer support, including WDTR
- * negotiation, programming of wide transfer capabilities
- * on reselection and table indirect selection.
- *
- * NCR53c710 - need to add fatal interrupt or GEN code for
- * command completion signaling. Need to modify all
- * SDID, SCID, etc. registers, and table indirect select code
- * since these use bit fielded (ie 1<<target) instead of
- * binary encoded target ids. Need to accommodate
- * different register mappings, probably scan through
- * the SCRIPT code and change the non SFBR register operand
- * of all MOVE instructions.
- *
- * It is rather worse than this actually, the 710 corrupts
- * both TEMP and DSA when you do a MOVE MEMORY. This
- * screws you up all over the place. MOVE MEMORY 4 with a
- * destination of DSA seems to work OK, which helps some.
- * Richard Hirst richard@sleepie.demon.co.uk
- *
- * NCR53c700/700-66 - need to add code to refix addresses on
- * every nexus change, eliminate all table indirect code,
- * very messy.
- *
- * 6. The NCR53c7x0 series is very popular on other platforms that
- * could be running Linux - ie, some high performance AMIGA SCSI
- * boards use it.
- *
- * So, I should include #ifdef'd code so that it is
- * compatible with these systems.
- *
- * Specifically, the little Endian assumptions I made in my
- * bit fields need to change, and if the NCR doesn't see memory
- * the right way, we need to provide options to reverse words
- * when the scripts are relocated.
- *
- * 7. Use vremap() to access memory mapped boards.
- */
-
-/*
- * Allow for simultaneous existence of multiple SCSI scripts so we
- * can have a single driver binary for all of the family.
- *
- * - one for NCR53c700 and NCR53c700-66 chips (not yet supported)
- * - one for rest (only the NCR53c810, 815, 820, and 825 are currently
- * supported)
- *
- * So that we only need two SCSI scripts, we need to modify things so
- * that we fixup register accesses in READ/WRITE instructions, and
- * we'll also have to accommodate the bit vs. binary encoding of IDs
- * with the 7xx chips.
- */
-
-#define ROUNDUP(adr,type) \
- ((void *) (((long) (adr) + sizeof(type) - 1) & ~(sizeof(type) - 1)))
-
-
-/*
- * Function: issue_to_cmd
- *
- * Purpose: convert jump instruction in issue array to NCR53c7x0_cmd
- * structure pointer.
- *
- * Inputs; issue - pointer to start of NOP or JUMP instruction
- * in issue array.
- *
- * Returns: pointer to command on success; 0 if opcode is NOP.
- */
-
-static inline struct NCR53c7x0_cmd *
-issue_to_cmd (struct Scsi_Host *host, struct NCR53c7x0_hostdata *hostdata,
- u32 *issue)
-{
- return (issue[0] != hostdata->NOP_insn) ?
- /*
- * If the IF TRUE bit is set, it's a JUMP instruction. The
- * operand is a bus pointer to the dsa_begin routine for this DSA. The
- * dsa field of the NCR53c7x0_cmd structure starts with the
- * DSA code template. By converting to a virtual address,
- * subtracting the code template size, and offset of the
- * dsa field, we end up with a pointer to the start of the
- * structure (alternatively, we could use the
- * dsa_cmnd field, an anachronism from when we weren't
- * sure what the relationship between the NCR structures
- * and host structures were going to be.
- */
- (struct NCR53c7x0_cmd *) ((char *) bus_to_virt (issue[1]) -
- (hostdata->E_dsa_code_begin - hostdata->E_dsa_code_template) -
- offsetof(struct NCR53c7x0_cmd, dsa))
- /* If the IF TRUE bit is not set, it's a NOP */
- : NULL;
-}
-
-
-/*
- * FIXME: we should junk these, in favor of synchronous_want and
- * wide_want in the NCR53c7x0_hostdata structure.
- */
-
-/* Template for "preferred" synchronous transfer parameters. */
-
-static const unsigned char sdtr_message[] = {
-#ifdef CONFIG_SCSI_NCR53C7xx_FAST
- EXTENDED_MESSAGE, 3 /* length */, EXTENDED_SDTR, 25 /* *4ns */, 8 /* off */
-#else
- EXTENDED_MESSAGE, 3 /* length */, EXTENDED_SDTR, 50 /* *4ns */, 8 /* off */
-#endif
-};
-
-/* Template to request asynchronous transfers */
-
-static const unsigned char async_message[] = {
- EXTENDED_MESSAGE, 3 /* length */, EXTENDED_SDTR, 0, 0 /* asynchronous */
-};
-
-/* Template for "preferred" WIDE transfer parameters */
-
-static const unsigned char wdtr_message[] = {
- EXTENDED_MESSAGE, 2 /* length */, EXTENDED_WDTR, 1 /* 2^1 bytes */
-};
-
-#if 0
-/*
- * Function : struct Scsi_Host *find_host (int host)
- *
- * Purpose : KGDB support function which translates a host number
- * to a host structure.
- *
- * Inputs : host - number of SCSI host
- *
- * Returns : NULL on failure, pointer to host structure on success.
- */
-
-static struct Scsi_Host *
-find_host (int host) {
- struct Scsi_Host *h;
- for (h = first_host; h && h->host_no != host; h = h->next);
- if (!h) {
- printk (KERN_ALERT "scsi%d not found\n", host);
- return NULL;
- } else if (h->hostt != the_template) {
- printk (KERN_ALERT "scsi%d is not a NCR board\n", host);
- return NULL;
- }
- return h;
-}
-
-#if 0
-/*
- * Function : request_synchronous (int host, int target)
- *
- * Purpose : KGDB interface which will allow us to negotiate for
- * synchronous transfers. This ill be replaced with a more
- * integrated function; perhaps a new entry in the scsi_host
- * structure, accessible via an ioctl() or perhaps /proc/scsi.
- *
- * Inputs : host - number of SCSI host; target - number of target.
- *
- * Returns : 0 when negotiation has been setup for next SCSI command,
- * -1 on failure.
- */
-
-static int
-request_synchronous (int host, int target) {
- struct Scsi_Host *h;
- struct NCR53c7x0_hostdata *hostdata;
- unsigned long flags;
- if (target < 0) {
- printk (KERN_ALERT "target %d is bogus\n", target);
- return -1;
- }
- if (!(h = find_host (host)))
- return -1;
- else if (h->this_id == target) {
- printk (KERN_ALERT "target %d is host ID\n", target);
- return -1;
- }
- else if (target >= h->max_id) {
- printk (KERN_ALERT "target %d exceeds maximum of %d\n", target,
- h->max_id);
- return -1;
- }
- hostdata = (struct NCR53c7x0_hostdata *)h->hostdata[0];
-
- local_irq_save(flags);
- if (hostdata->initiate_sdtr & (1 << target)) {
- local_irq_restore(flags);
- printk (KERN_ALERT "target %d already doing SDTR\n", target);
- return -1;
- }
- hostdata->initiate_sdtr |= (1 << target);
- local_irq_restore(flags);
- return 0;
-}
-#endif
-
-/*
- * Function : request_disconnect (int host, int on_or_off)
- *
- * Purpose : KGDB support function, tells us to allow or disallow
- * disconnections.
- *
- * Inputs : host - number of SCSI host; on_or_off - non-zero to allow,
- * zero to disallow.
- *
- * Returns : 0 on success, * -1 on failure.
- */
-
-static int
-request_disconnect (int host, int on_or_off) {
- struct Scsi_Host *h;
- struct NCR53c7x0_hostdata *hostdata;
- if (!(h = find_host (host)))
- return -1;
- hostdata = (struct NCR53c7x0_hostdata *) h->hostdata[0];
- if (on_or_off)
- hostdata->options |= OPTION_DISCONNECT;
- else
- hostdata->options &= ~OPTION_DISCONNECT;
- return 0;
-}
-#endif
-
-/*
- * Function : static void NCR53c7x0_driver_init (struct Scsi_Host *host)
- *
- * Purpose : Initialize internal structures, as required on startup, or
- * after a SCSI bus reset.
- *
- * Inputs : host - pointer to this host adapter's structure
- */
-
-static void
-NCR53c7x0_driver_init (struct Scsi_Host *host) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- int i, j;
- u32 *ncrcurrent;
-
- for (i = 0; i < 16; ++i) {
- hostdata->request_sense[i] = 0;
- for (j = 0; j < 8; ++j)
- hostdata->busy[i][j] = 0;
- set_synchronous (host, i, /* sxfer */ 0, hostdata->saved_scntl3, 0);
- }
- hostdata->issue_queue = NULL;
- hostdata->running_list = hostdata->finished_queue =
- hostdata->ncrcurrent = NULL;
- for (i = 0, ncrcurrent = (u32 *) hostdata->schedule;
- i < host->can_queue; ++i, ncrcurrent += 2) {
- ncrcurrent[0] = hostdata->NOP_insn;
- ncrcurrent[1] = 0xdeadbeef;
- }
- ncrcurrent[0] = ((DCMD_TYPE_TCI|DCMD_TCI_OP_JUMP) << 24) | DBC_TCI_TRUE;
- ncrcurrent[1] = (u32) virt_to_bus (hostdata->script) +
- hostdata->E_wait_reselect;
- hostdata->reconnect_dsa_head = 0;
- hostdata->addr_reconnect_dsa_head = (u32)
- virt_to_bus((void *) &(hostdata->reconnect_dsa_head));
- hostdata->expecting_iid = 0;
- hostdata->expecting_sto = 0;
- if (hostdata->options & OPTION_ALWAYS_SYNCHRONOUS)
- hostdata->initiate_sdtr = 0xffff;
- else
- hostdata->initiate_sdtr = 0;
- hostdata->talked_to = 0;
- hostdata->idle = 1;
-}
-
-/*
- * Function : static int clock_to_ccf_710 (int clock)
- *
- * Purpose : Return the clock conversion factor for a given SCSI clock.
- *
- * Inputs : clock - SCSI clock expressed in Hz.
- *
- * Returns : ccf on success, -1 on failure.
- */
-
-static int
-clock_to_ccf_710 (int clock) {
- if (clock <= 16666666)
- return -1;
- if (clock <= 25000000)
- return 2; /* Divide by 1.0 */
- else if (clock <= 37500000)
- return 1; /* Divide by 1.5 */
- else if (clock <= 50000000)
- return 0; /* Divide by 2.0 */
- else if (clock <= 66000000)
- return 3; /* Divide by 3.0 */
- else
- return -1;
-}
-
-/*
- * Function : static int NCR53c7x0_init (struct Scsi_Host *host)
- *
- * Purpose : initialize the internal structures for a given SCSI host
- *
- * Inputs : host - pointer to this host adapter's structure
- *
- * Preconditions : when this function is called, the chip_type
- * field of the hostdata structure MUST have been set.
- *
- * Returns : 0 on success, -1 on failure.
- */
-
-int
-NCR53c7x0_init (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- int i, ccf;
- unsigned char revision;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- /*
- * There are some things which we need to know about in order to provide
- * a semblance of support. Print 'em if they aren't what we expect,
- * otherwise don't add to the noise.
- *
- * -1 means we don't know what to expect.
- */
- int val, flags;
- char buf[32];
- int expected_id = -1;
- int expected_clock = -1;
- int uninitialized = 0;
-#ifdef NO_IO_SPACE
- int expected_mapping = OPTION_MEMORY_MAPPED;
-#else
- int expected_mapping = OPTION_IO_MAPPED;
-#endif
- for (i=0;i<7;i++)
- hostdata->valid_ids[i] = 1; /* Default all ID's to scan */
-
- /* Parse commandline flags */
- if (check_setup_strings("noasync",&flags,&val,buf))
- {
- hostdata->options |= OPTION_NO_ASYNC;
- hostdata->options &= ~(OPTION_SYNCHRONOUS | OPTION_ALWAYS_SYNCHRONOUS);
- }
-
- if (check_setup_strings("nosync",&flags,&val,buf))
- {
- hostdata->options &= ~(OPTION_SYNCHRONOUS | OPTION_ALWAYS_SYNCHRONOUS);
- }
-
- if (check_setup_strings("nodisconnect",&flags,&val,buf))
- hostdata->options &= ~OPTION_DISCONNECT;
-
- if (check_setup_strings("validids",&flags,&val,buf))
- {
- for (i=0;i<7;i++)
- hostdata->valid_ids[i] = val & (1<<i);
- }
-
- if ((i = check_setup_strings("next",&flags,&val,buf)))
- {
- while (i)
- setup_used[--i] = 1;
- }
-
- if (check_setup_strings("opthi",&flags,&val,buf))
- hostdata->options = (long long)val << 32;
- if (check_setup_strings("optlo",&flags,&val,buf))
- hostdata->options |= val;
-
- NCR53c7x0_local_setup(host);
- switch (hostdata->chip) {
- case 710:
- case 770:
- hostdata->dstat_sir_intr = NCR53c7x0_dstat_sir_intr;
- hostdata->init_save_regs = NULL;
- hostdata->dsa_fixup = NCR53c7xx_dsa_fixup;
- hostdata->init_fixup = NCR53c7x0_init_fixup;
- hostdata->soft_reset = NCR53c7x0_soft_reset;
- hostdata->run_tests = NCR53c7xx_run_tests;
- expected_clock = hostdata->scsi_clock;
- expected_id = 7;
- break;
- default:
- printk ("scsi%d : chip type of %d is not supported yet, detaching.\n",
- host->host_no, hostdata->chip);
- scsi_unregister (host);
- return -1;
- }
-
- /* Assign constants accessed by NCR */
- hostdata->NCR53c7xx_zero = 0;
- hostdata->NCR53c7xx_msg_reject = MESSAGE_REJECT;
- hostdata->NCR53c7xx_msg_abort = ABORT;
- hostdata->NCR53c7xx_msg_nop = NOP;
- hostdata->NOP_insn = (DCMD_TYPE_TCI|DCMD_TCI_OP_JUMP) << 24;
- if (expected_mapping == -1 ||
- (hostdata->options & (OPTION_MEMORY_MAPPED)) !=
- (expected_mapping & OPTION_MEMORY_MAPPED))
- printk ("scsi%d : using %s mapped access\n", host->host_no,
- (hostdata->options & OPTION_MEMORY_MAPPED) ? "memory" :
- "io");
-
- hostdata->dmode = (hostdata->chip == 700 || hostdata->chip == 70066) ?
- DMODE_REG_00 : DMODE_REG_10;
- hostdata->istat = ((hostdata->chip / 100) == 8) ?
- ISTAT_REG_800 : ISTAT_REG_700;
-
-/* We have to assume that this may be the first access to the chip, so
- * we must set EA in DCNTL. */
-
- NCR53c7x0_write8 (DCNTL_REG, DCNTL_10_EA|DCNTL_10_COM);
-
-
-/* Only the ISTAT register is readable when the NCR is running, so make
- sure it's halted. */
- ncr_halt(host);
-
-/*
- * XXX - the NCR53c700 uses bitfielded registers for SCID, SDID, etc,
- * as does the 710 with one bit per SCSI ID. Conversely, the NCR
- * uses a normal, 3 bit binary representation of these values.
- *
- * Get the rest of the NCR documentation, and FIND OUT where the change
- * was.
- */
-
-#if 0
- /* May not be able to do this - chip my not have been set up yet */
- tmp = hostdata->this_id_mask = NCR53c7x0_read8(SCID_REG);
- for (host->this_id = 0; tmp != 1; tmp >>=1, ++host->this_id);
-#else
- host->this_id = 7;
-#endif
-
-/*
- * Note : we should never encounter a board setup for ID0. So,
- * if we see ID0, assume that it was uninitialized and set it
- * to the industry standard 7.
- */
- if (!host->this_id) {
- printk("scsi%d : initiator ID was %d, changing to 7\n",
- host->host_no, host->this_id);
- host->this_id = 7;
- hostdata->this_id_mask = 1 << 7;
- uninitialized = 1;
- };
-
- if (expected_id == -1 || host->this_id != expected_id)
- printk("scsi%d : using initiator ID %d\n", host->host_no,
- host->this_id);
-
- /*
- * Save important registers to allow a soft reset.
- */
-
- /*
- * CTEST7 controls cache snooping, burst mode, and support for
- * external differential drivers. This isn't currently used - the
- * default value may not be optimal anyway.
- * Even worse, it may never have been set up since reset.
- */
- hostdata->saved_ctest7 = NCR53c7x0_read8(CTEST7_REG) & CTEST7_SAVE;
- revision = (NCR53c7x0_read8(CTEST8_REG) & 0xF0) >> 4;
- switch (revision) {
- case 1: revision = 0; break;
- case 2: revision = 1; break;
- case 4: revision = 2; break;
- case 8: revision = 3; break;
- default: revision = 255; break;
- }
- printk("scsi%d: Revision 0x%x\n",host->host_no,revision);
-
- if ((revision == 0 || revision == 255) && (hostdata->options & (OPTION_SYNCHRONOUS|OPTION_DISCONNECT|OPTION_ALWAYS_SYNCHRONOUS)))
- {
- printk ("scsi%d: Disabling sync working and disconnect/reselect\n",
- host->host_no);
- hostdata->options &= ~(OPTION_SYNCHRONOUS|OPTION_DISCONNECT|OPTION_ALWAYS_SYNCHRONOUS);
- }
-
- /*
- * On NCR53c700 series chips, DCNTL controls the SCSI clock divisor,
- * on 800 series chips, it allows for a totem-pole IRQ driver.
- * NOTE saved_dcntl currently overwritten in init function.
- * The value read here may be garbage anyway, MVME16x board at least
- * does not initialise chip if kernel arrived via tftp.
- */
-
- hostdata->saved_dcntl = NCR53c7x0_read8(DCNTL_REG);
-
- /*
- * DMODE controls DMA burst length, and on 700 series chips,
- * 286 mode and bus width
- * NOTE: On MVME16x, chip may have been reset, so this could be a
- * power-on/reset default value.
- */
- hostdata->saved_dmode = NCR53c7x0_read8(hostdata->dmode);
-
- /*
- * Now that burst length and enabled/disabled status is known,
- * clue the user in on it.
- */
-
- ccf = clock_to_ccf_710 (expected_clock);
-
- for (i = 0; i < 16; ++i)
- hostdata->cmd_allocated[i] = 0;
-
- if (hostdata->init_save_regs)
- hostdata->init_save_regs (host);
- if (hostdata->init_fixup)
- hostdata->init_fixup (host);
-
- if (!the_template) {
- the_template = host->hostt;
- first_host = host;
- }
-
- /*
- * Linux SCSI drivers have always been plagued with initialization
- * problems - some didn't work with the BIOS disabled since they expected
- * initialization from it, some didn't work when the networking code
- * was enabled and registers got scrambled, etc.
- *
- * To avoid problems like this, in the future, we will do a soft
- * reset on the SCSI chip, taking it back to a sane state.
- */
-
- hostdata->soft_reset (host);
-
-#if 1
- hostdata->debug_count_limit = -1;
-#else
- hostdata->debug_count_limit = 1;
-#endif
- hostdata->intrs = -1;
- hostdata->resets = -1;
- memcpy ((void *) hostdata->synchronous_want, (void *) sdtr_message,
- sizeof (hostdata->synchronous_want));
-
- NCR53c7x0_driver_init (host);
-
- if (request_irq(host->irq, NCR53c7x0_intr, IRQF_SHARED, "53c7xx", host))
- {
- printk("scsi%d : IRQ%d not free, detaching\n",
- host->host_no, host->irq);
- goto err_unregister;
- }
-
- if ((hostdata->run_tests && hostdata->run_tests(host) == -1) ||
- (hostdata->options & OPTION_DEBUG_TESTS_ONLY)) {
- /* XXX Should disable interrupts, etc. here */
- goto err_free_irq;
- } else {
- if (host->io_port) {
- host->n_io_port = 128;
- if (!request_region (host->io_port, host->n_io_port, "ncr53c7xx"))
- goto err_free_irq;
- }
- }
-
- if (NCR53c7x0_read8 (SBCL_REG) & SBCL_BSY) {
- printk ("scsi%d : bus wedge, doing SCSI reset\n", host->host_no);
- hard_reset (host);
- }
- return 0;
-
- err_free_irq:
- free_irq(host->irq, NCR53c7x0_intr);
- err_unregister:
- scsi_unregister(host);
- return -1;
-}
-
-/*
- * Function : int ncr53c7xx_init(struct scsi_host_template *tpnt, int board, int chip,
- * unsigned long base, int io_port, int irq, int dma, long long options,
- * int clock);
- *
- * Purpose : initializes a NCR53c7,8x0 based on base addresses,
- * IRQ, and DMA channel.
- *
- * Inputs : tpnt - Template for this SCSI adapter, board - board level
- * product, chip - 710
- *
- * Returns : 0 on success, -1 on failure.
- *
- */
-
-int
-ncr53c7xx_init (struct scsi_host_template *tpnt, int board, int chip,
- unsigned long base, int io_port, int irq, int dma,
- long long options, int clock)
-{
- struct Scsi_Host *instance;
- struct NCR53c7x0_hostdata *hostdata;
- char chip_str[80];
- int script_len = 0, dsa_len = 0, size = 0, max_cmd_size = 0,
- schedule_size = 0, ok = 0;
- void *tmp;
- unsigned long page;
-
- switch (chip) {
- case 710:
- case 770:
- schedule_size = (tpnt->can_queue + 1) * 8 /* JUMP instruction size */;
- script_len = NCR53c7xx_script_len;
- dsa_len = NCR53c7xx_dsa_len;
- options |= OPTION_INTFLY;
- sprintf (chip_str, "NCR53c%d", chip);
- break;
- default:
- printk("scsi-ncr53c7xx : unsupported SCSI chip %d\n", chip);
- return -1;
- }
-
- printk("scsi-ncr53c7xx : %s at memory 0x%lx, io 0x%x, irq %d",
- chip_str, base, io_port, irq);
- if (dma == DMA_NONE)
- printk("\n");
- else
- printk(", dma %d\n", dma);
-
- if (options & OPTION_DEBUG_PROBE_ONLY) {
- printk ("scsi-ncr53c7xx : probe only enabled, aborting initialization\n");
- return -1;
- }
-
- max_cmd_size = sizeof(struct NCR53c7x0_cmd) + dsa_len +
- /* Size of dynamic part of command structure : */
- 2 * /* Worst case : we don't know if we need DATA IN or DATA out */
- ( 2 * /* Current instructions per scatter/gather segment */
- tpnt->sg_tablesize +
- 3 /* Current startup / termination required per phase */
- ) *
- 8 /* Each instruction is eight bytes */;
-
- /* Allocate fixed part of hostdata, dynamic part to hold appropriate
- SCSI SCRIPT(tm) plus a single, maximum-sized NCR53c7x0_cmd structure.
-
- We need a NCR53c7x0_cmd structure for scan_scsis() when we are
- not loaded as a module, and when we're loaded as a module, we
- can't use a non-dynamically allocated structure because modules
- are vmalloc()'d, which can allow structures to cross page
- boundaries and breaks our physical/virtual address assumptions
- for DMA.
-
- So, we stick it past the end of our hostdata structure.
-
- ASSUMPTION :
- Regardless of how many simultaneous SCSI commands we allow,
- the probe code only executes a _single_ instruction at a time,
- so we only need one here, and don't need to allocate NCR53c7x0_cmd
- structures for each target until we are no longer in scan_scsis
- and kmalloc() has become functional (memory_init() happens
- after all device driver initialization).
- */
-
- size = sizeof(struct NCR53c7x0_hostdata) + script_len +
- /* Note that alignment will be guaranteed, since we put the command
- allocated at probe time after the fixed-up SCSI script, which
- consists of 32 bit words, aligned on a 32 bit boundary. But
- on a 64bit machine we need 8 byte alignment for hostdata->free, so
- we add in another 4 bytes to take care of potential misalignment
- */
- (sizeof(void *) - sizeof(u32)) + max_cmd_size + schedule_size;
-
- page = __get_free_pages(GFP_ATOMIC,1);
- if(page==0)
- {
- printk(KERN_ERR "53c7xx: out of memory.\n");
- return -ENOMEM;
- }
-#ifdef FORCE_DSA_ALIGNMENT
- /*
- * 53c710 rev.0 doesn't have an add-with-carry instruction.
- * Ensure we allocate enough memory to force DSA alignment.
- */
- size += 256;
-#endif
- /* Size should be < 8K, so we can fit it in two pages. */
- if (size > 8192) {
- printk(KERN_ERR "53c7xx: hostdata > 8K\n");
- return -1;
- }
-
- instance = scsi_register (tpnt, 4);
- if (!instance)
- {
- free_page(page);
- return -1;
- }
- instance->hostdata[0] = page;
- memset((void *)instance->hostdata[0], 0, 8192);
- cache_push(virt_to_phys((void *)(instance->hostdata[0])), 8192);
- cache_clear(virt_to_phys((void *)(instance->hostdata[0])), 8192);
- kernel_set_cachemode((void *)instance->hostdata[0], 8192, IOMAP_NOCACHE_SER);
-
- /* FIXME : if we ever support an ISA NCR53c7xx based board, we
- need to check if the chip is running in a 16 bit mode, and if so
- unregister it if it is past the 16M (0x1000000) mark */
-
- hostdata = (struct NCR53c7x0_hostdata *)instance->hostdata[0];
- hostdata->size = size;
- hostdata->script_count = script_len / sizeof(u32);
- hostdata->board = board;
- hostdata->chip = chip;
-
- /*
- * Being memory mapped is more desirable, since
- *
- * - Memory accesses may be faster.
- *
- * - The destination and source address spaces are the same for
- * all instructions, meaning we don't have to twiddle dmode or
- * any other registers.
- *
- * So, we try for memory mapped, and if we don't get it,
- * we go for port mapped, and that failing we tell the user
- * it can't work.
- */
-
- if (base) {
- instance->base = base;
- /* Check for forced I/O mapping */
- if (!(options & OPTION_IO_MAPPED)) {
- options |= OPTION_MEMORY_MAPPED;
- ok = 1;
- }
- } else {
- options &= ~OPTION_MEMORY_MAPPED;
- }
-
- if (io_port) {
- instance->io_port = io_port;
- options |= OPTION_IO_MAPPED;
- ok = 1;
- } else {
- options &= ~OPTION_IO_MAPPED;
- }
-
- if (!ok) {
- printk ("scsi%d : not initializing, no I/O or memory mapping known \n",
- instance->host_no);
- scsi_unregister (instance);
- return -1;
- }
- instance->irq = irq;
- instance->dma_channel = dma;
-
- hostdata->options = options;
- hostdata->dsa_len = dsa_len;
- hostdata->max_cmd_size = max_cmd_size;
- hostdata->num_cmds = 1;
- hostdata->scsi_clock = clock;
- /* Initialize single command */
- tmp = (hostdata->script + hostdata->script_count);
-#ifdef FORCE_DSA_ALIGNMENT
- {
- void *t = ROUNDUP(tmp, void *);
- if (((u32)t & 0xff) > CmdPageStart)
- t = (void *)((u32)t + 255);
- t = (void *)(((u32)t & ~0xff) + CmdPageStart);
- hostdata->free = t;
-#if 0
- printk ("scsi: Registered size increased by 256 to %d\n", size);
- printk ("scsi: CmdPageStart = 0x%02x\n", CmdPageStart);
- printk ("scsi: tmp = 0x%08x, hostdata->free set to 0x%08x\n",
- (u32)tmp, (u32)t);
-#endif
- }
-#else
- hostdata->free = ROUNDUP(tmp, void *);
-#endif
- hostdata->free->real = tmp;
- hostdata->free->size = max_cmd_size;
- hostdata->free->free = NULL;
- hostdata->free->next = NULL;
- hostdata->extra_allocate = 0;
-
- /* Allocate command start code space */
- hostdata->schedule = (chip == 700 || chip == 70066) ?
- NULL : (u32 *) ((char *)hostdata->free + max_cmd_size);
-
-/*
- * For diagnostic purposes, we don't really care how fast things blaze.
- * For profiling, we want to access the 800ns resolution system clock,
- * using a 'C' call on the host processor.
- *
- * Therefore, there's no need for the NCR chip to directly manipulate
- * this data, and we should put it wherever is most convenient for
- * Linux.
- */
- if (track_events)
- hostdata->events = (struct NCR53c7x0_event *) (track_events ?
- vmalloc (sizeof (struct NCR53c7x0_event) * track_events) : NULL);
- else
- hostdata->events = NULL;
-
- if (hostdata->events) {
- memset ((void *) hostdata->events, 0, sizeof(struct NCR53c7x0_event) *
- track_events);
- hostdata->event_size = track_events;
- hostdata->event_index = 0;
- } else
- hostdata->event_size = 0;
-
- return NCR53c7x0_init(instance);
-}
-
-
-/*
- * Function : static void NCR53c7x0_init_fixup (struct Scsi_Host *host)
- *
- * Purpose : copy and fixup the SCSI SCRIPTS(tm) code for this device.
- *
- * Inputs : host - pointer to this host adapter's structure
- *
- */
-
-static void
-NCR53c7x0_init_fixup (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned char tmp;
- int i, ncr_to_memory, memory_to_ncr;
- u32 base;
- NCR53c7x0_local_setup(host);
-
-
- /* XXX - NOTE : this code MUST be made endian aware */
- /* Copy code into buffer that was allocated at detection time. */
- memcpy ((void *) hostdata->script, (void *) SCRIPT,
- sizeof(SCRIPT));
- /* Fixup labels */
- for (i = 0; i < PATCHES; ++i)
- hostdata->script[LABELPATCHES[i]] +=
- virt_to_bus(hostdata->script);
- /* Fixup addresses of constants that used to be EXTERNAL */
-
- patch_abs_32 (hostdata->script, 0, NCR53c7xx_msg_abort,
- virt_to_bus(&(hostdata->NCR53c7xx_msg_abort)));
- patch_abs_32 (hostdata->script, 0, NCR53c7xx_msg_reject,
- virt_to_bus(&(hostdata->NCR53c7xx_msg_reject)));
- patch_abs_32 (hostdata->script, 0, NCR53c7xx_zero,
- virt_to_bus(&(hostdata->NCR53c7xx_zero)));
- patch_abs_32 (hostdata->script, 0, NCR53c7xx_sink,
- virt_to_bus(&(hostdata->NCR53c7xx_sink)));
- patch_abs_32 (hostdata->script, 0, NOP_insn,
- virt_to_bus(&(hostdata->NOP_insn)));
- patch_abs_32 (hostdata->script, 0, schedule,
- virt_to_bus((void *) hostdata->schedule));
-
- /* Fixup references to external variables: */
- for (i = 0; i < EXTERNAL_PATCHES_LEN; ++i)
- hostdata->script[EXTERNAL_PATCHES[i].offset] +=
- virt_to_bus(EXTERNAL_PATCHES[i].address);
-
- /*
- * Fixup absolutes set at boot-time.
- *
- * All non-code absolute variables suffixed with "dsa_" and "int_"
- * are constants, and need no fixup provided the assembler has done
- * it for us (I don't know what the "real" NCR assembler does in
- * this case, my assembler does the right magic).
- */
-
- patch_abs_rwri_data (hostdata->script, 0, dsa_save_data_pointer,
- Ent_dsa_code_save_data_pointer - Ent_dsa_zero);
- patch_abs_rwri_data (hostdata->script, 0, dsa_restore_pointers,
- Ent_dsa_code_restore_pointers - Ent_dsa_zero);
- patch_abs_rwri_data (hostdata->script, 0, dsa_check_reselect,
- Ent_dsa_code_check_reselect - Ent_dsa_zero);
-
- /*
- * Just for the hell of it, preserve the settings of
- * Burst Length and Enable Read Line bits from the DMODE
- * register. Make sure SCRIPTS start automagically.
- */
-
-#if defined(CONFIG_MVME16x) || defined(CONFIG_BVME6000)
- /* We know better what we want than 16xBug does! */
- tmp = DMODE_10_BL_8 | DMODE_10_FC2;
-#else
- tmp = NCR53c7x0_read8(DMODE_REG_10);
- tmp &= (DMODE_BL_MASK | DMODE_10_FC2 | DMODE_10_FC1 | DMODE_710_PD |
- DMODE_710_UO);
-#endif
-
- if (!(hostdata->options & OPTION_MEMORY_MAPPED)) {
- base = (u32) host->io_port;
- memory_to_ncr = tmp|DMODE_800_DIOM;
- ncr_to_memory = tmp|DMODE_800_SIOM;
- } else {
- base = virt_to_bus((void *)host->base);
- memory_to_ncr = ncr_to_memory = tmp;
- }
-
- /* SCRATCHB_REG_10 == SCRATCHA_REG_800, as it happens */
- patch_abs_32 (hostdata->script, 0, addr_scratch, base + SCRATCHA_REG_800);
- patch_abs_32 (hostdata->script, 0, addr_temp, base + TEMP_REG);
- patch_abs_32 (hostdata->script, 0, addr_dsa, base + DSA_REG);
-
- /*
- * I needed some variables in the script to be accessible to
- * both the NCR chip and the host processor. For these variables,
- * I made the arbitrary decision to store them directly in the
- * hostdata structure rather than in the RELATIVE area of the
- * SCRIPTS.
- */
-
-
- patch_abs_rwri_data (hostdata->script, 0, dmode_memory_to_memory, tmp);
- patch_abs_rwri_data (hostdata->script, 0, dmode_memory_to_ncr, memory_to_ncr);
- patch_abs_rwri_data (hostdata->script, 0, dmode_ncr_to_memory, ncr_to_memory);
-
- patch_abs_32 (hostdata->script, 0, msg_buf,
- virt_to_bus((void *)&(hostdata->msg_buf)));
- patch_abs_32 (hostdata->script, 0, reconnect_dsa_head,
- virt_to_bus((void *)&(hostdata->reconnect_dsa_head)));
- patch_abs_32 (hostdata->script, 0, addr_reconnect_dsa_head,
- virt_to_bus((void *)&(hostdata->addr_reconnect_dsa_head)));
- patch_abs_32 (hostdata->script, 0, reselected_identify,
- virt_to_bus((void *)&(hostdata->reselected_identify)));
-/* reselected_tag is currently unused */
-#if 0
- patch_abs_32 (hostdata->script, 0, reselected_tag,
- virt_to_bus((void *)&(hostdata->reselected_tag)));
-#endif
-
- patch_abs_32 (hostdata->script, 0, test_dest,
- virt_to_bus((void*)&hostdata->test_dest));
- patch_abs_32 (hostdata->script, 0, test_src,
- virt_to_bus(&hostdata->test_source));
- patch_abs_32 (hostdata->script, 0, saved_dsa,
- virt_to_bus((void *)&hostdata->saved2_dsa));
- patch_abs_32 (hostdata->script, 0, emulfly,
- virt_to_bus((void *)&hostdata->emulated_intfly));
-
- patch_abs_rwri_data (hostdata->script, 0, dsa_check_reselect,
- (unsigned char)(Ent_dsa_code_check_reselect - Ent_dsa_zero));
-
-/* These are for event logging; the ncr_event enum contains the
- actual interrupt numbers. */
-#ifdef A_int_EVENT_SELECT
- patch_abs_32 (hostdata->script, 0, int_EVENT_SELECT, (u32) EVENT_SELECT);
-#endif
-#ifdef A_int_EVENT_DISCONNECT
- patch_abs_32 (hostdata->script, 0, int_EVENT_DISCONNECT, (u32) EVENT_DISCONNECT);
-#endif
-#ifdef A_int_EVENT_RESELECT
- patch_abs_32 (hostdata->script, 0, int_EVENT_RESELECT, (u32) EVENT_RESELECT);
-#endif
-#ifdef A_int_EVENT_COMPLETE
- patch_abs_32 (hostdata->script, 0, int_EVENT_COMPLETE, (u32) EVENT_COMPLETE);
-#endif
-#ifdef A_int_EVENT_IDLE
- patch_abs_32 (hostdata->script, 0, int_EVENT_IDLE, (u32) EVENT_IDLE);
-#endif
-#ifdef A_int_EVENT_SELECT_FAILED
- patch_abs_32 (hostdata->script, 0, int_EVENT_SELECT_FAILED,
- (u32) EVENT_SELECT_FAILED);
-#endif
-#ifdef A_int_EVENT_BEFORE_SELECT
- patch_abs_32 (hostdata->script, 0, int_EVENT_BEFORE_SELECT,
- (u32) EVENT_BEFORE_SELECT);
-#endif
-#ifdef A_int_EVENT_RESELECT_FAILED
- patch_abs_32 (hostdata->script, 0, int_EVENT_RESELECT_FAILED,
- (u32) EVENT_RESELECT_FAILED);
-#endif
-
- /*
- * Make sure the NCR and Linux code agree on the location of
- * certain fields.
- */
-
- hostdata->E_accept_message = Ent_accept_message;
- hostdata->E_command_complete = Ent_command_complete;
- hostdata->E_cmdout_cmdout = Ent_cmdout_cmdout;
- hostdata->E_data_transfer = Ent_data_transfer;
- hostdata->E_debug_break = Ent_debug_break;
- hostdata->E_dsa_code_template = Ent_dsa_code_template;
- hostdata->E_dsa_code_template_end = Ent_dsa_code_template_end;
- hostdata->E_end_data_transfer = Ent_end_data_transfer;
- hostdata->E_initiator_abort = Ent_initiator_abort;
- hostdata->E_msg_in = Ent_msg_in;
- hostdata->E_other_transfer = Ent_other_transfer;
- hostdata->E_other_in = Ent_other_in;
- hostdata->E_other_out = Ent_other_out;
- hostdata->E_reject_message = Ent_reject_message;
- hostdata->E_respond_message = Ent_respond_message;
- hostdata->E_select = Ent_select;
- hostdata->E_select_msgout = Ent_select_msgout;
- hostdata->E_target_abort = Ent_target_abort;
-#ifdef Ent_test_0
- hostdata->E_test_0 = Ent_test_0;
-#endif
- hostdata->E_test_1 = Ent_test_1;
- hostdata->E_test_2 = Ent_test_2;
-#ifdef Ent_test_3
- hostdata->E_test_3 = Ent_test_3;
-#endif
- hostdata->E_wait_reselect = Ent_wait_reselect;
- hostdata->E_dsa_code_begin = Ent_dsa_code_begin;
-
- hostdata->dsa_cmdout = A_dsa_cmdout;
- hostdata->dsa_cmnd = A_dsa_cmnd;
- hostdata->dsa_datain = A_dsa_datain;
- hostdata->dsa_dataout = A_dsa_dataout;
- hostdata->dsa_end = A_dsa_end;
- hostdata->dsa_msgin = A_dsa_msgin;
- hostdata->dsa_msgout = A_dsa_msgout;
- hostdata->dsa_msgout_other = A_dsa_msgout_other;
- hostdata->dsa_next = A_dsa_next;
- hostdata->dsa_select = A_dsa_select;
- hostdata->dsa_start = Ent_dsa_code_template - Ent_dsa_zero;
- hostdata->dsa_status = A_dsa_status;
- hostdata->dsa_jump_dest = Ent_dsa_code_fix_jump - Ent_dsa_zero +
- 8 /* destination operand */;
-
- /* sanity check */
- if (A_dsa_fields_start != Ent_dsa_code_template_end -
- Ent_dsa_zero)
- printk("scsi%d : NCR dsa_fields start is %d not %d\n",
- host->host_no, A_dsa_fields_start, Ent_dsa_code_template_end -
- Ent_dsa_zero);
-
- printk("scsi%d : NCR code relocated to 0x%lx (virt 0x%p)\n", host->host_no,
- virt_to_bus(hostdata->script), hostdata->script);
-}
-
-/*
- * Function : static int NCR53c7xx_run_tests (struct Scsi_Host *host)
- *
- * Purpose : run various verification tests on the NCR chip,
- * including interrupt generation, and proper bus mastering
- * operation.
- *
- * Inputs : host - a properly initialized Scsi_Host structure
- *
- * Preconditions : the NCR chip must be in a halted state.
- *
- * Returns : 0 if all tests were successful, -1 on error.
- *
- */
-
-static int
-NCR53c7xx_run_tests (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned long timeout;
- u32 start;
- int failed, i;
- unsigned long flags;
- NCR53c7x0_local_setup(host);
-
- /* The NCR chip _must_ be idle to run the test scripts */
-
- local_irq_save(flags);
- if (!hostdata->idle) {
- printk ("scsi%d : chip not idle, aborting tests\n", host->host_no);
- local_irq_restore(flags);
- return -1;
- }
-
- /*
- * Check for functional interrupts, this could work as an
- * autoprobe routine.
- */
-
- if ((hostdata->options & OPTION_DEBUG_TEST1) &&
- hostdata->state != STATE_DISABLED) {
- hostdata->idle = 0;
- hostdata->test_running = 1;
- hostdata->test_completed = -1;
- hostdata->test_dest = 0;
- hostdata->test_source = 0xdeadbeef;
- start = virt_to_bus (hostdata->script) + hostdata->E_test_1;
- hostdata->state = STATE_RUNNING;
- printk ("scsi%d : test 1", host->host_no);
- NCR53c7x0_write32 (DSP_REG, start);
- if (hostdata->options & OPTION_DEBUG_TRACE)
- NCR53c7x0_write8 (DCNTL_REG, hostdata->saved_dcntl | DCNTL_SSM |
- DCNTL_STD);
- printk (" started\n");
- local_irq_restore(flags);
-
- /*
- * This is currently a .5 second timeout, since (in theory) no slow
- * board will take that long. In practice, we've seen one
- * pentium which occassionally fails with this, but works with
- * 10 times as much?
- */
-
- timeout = jiffies + 5 * HZ / 10;
- while ((hostdata->test_completed == -1) && time_before(jiffies, timeout))
- barrier();
-
- failed = 1;
- if (hostdata->test_completed == -1)
- printk ("scsi%d : driver test 1 timed out%s\n",host->host_no ,
- (hostdata->test_dest == 0xdeadbeef) ?
- " due to lost interrupt.\n"
- " Please verify that the correct IRQ is being used for your board,\n"
- : "");
- else if (hostdata->test_completed != 1)
- printk ("scsi%d : test 1 bad interrupt value (%d)\n",
- host->host_no, hostdata->test_completed);
- else
- failed = (hostdata->test_dest != 0xdeadbeef);
-
- if (hostdata->test_dest != 0xdeadbeef) {
- printk ("scsi%d : driver test 1 read 0x%x instead of 0xdeadbeef indicating a\n"
- " probable cache invalidation problem. Please configure caching\n"
- " as write-through or disabled\n",
- host->host_no, hostdata->test_dest);
- }
-
- if (failed) {
- printk ("scsi%d : DSP = 0x%p (script at 0x%p, start at 0x%x)\n",
- host->host_no, bus_to_virt(NCR53c7x0_read32(DSP_REG)),
- hostdata->script, start);
- printk ("scsi%d : DSPS = 0x%x\n", host->host_no,
- NCR53c7x0_read32(DSPS_REG));
- local_irq_restore(flags);
- return -1;
- }
- hostdata->test_running = 0;
- }
-
- if ((hostdata->options & OPTION_DEBUG_TEST2) &&
- hostdata->state != STATE_DISABLED) {
- u32 dsa[48];
- unsigned char identify = IDENTIFY(0, 0);
- unsigned char cmd[6];
- unsigned char data[36];
- unsigned char status = 0xff;
- unsigned char msg = 0xff;
-
- cmd[0] = INQUIRY;
- cmd[1] = cmd[2] = cmd[3] = cmd[5] = 0;
- cmd[4] = sizeof(data);
-
- dsa[2] = 1;
- dsa[3] = virt_to_bus(&identify);
- dsa[4] = 6;
- dsa[5] = virt_to_bus(&cmd);
- dsa[6] = sizeof(data);
- dsa[7] = virt_to_bus(&data);
- dsa[8] = 1;
- dsa[9] = virt_to_bus(&status);
- dsa[10] = 1;
- dsa[11] = virt_to_bus(&msg);
-
- for (i = 0; i < 6; ++i) {
-#ifdef VALID_IDS
- if (!hostdata->valid_ids[i])
- continue;
-#endif
- local_irq_disable();
- if (!hostdata->idle) {
- printk ("scsi%d : chip not idle, aborting tests\n", host->host_no);
- local_irq_restore(flags);
- return -1;
- }
-
- /* 710: bit mapped scsi ID, async */
- dsa[0] = (1 << i) << 16;
- hostdata->idle = 0;
- hostdata->test_running = 2;
- hostdata->test_completed = -1;
- start = virt_to_bus(hostdata->script) + hostdata->E_test_2;
- hostdata->state = STATE_RUNNING;
- NCR53c7x0_write32 (DSA_REG, virt_to_bus(dsa));
- NCR53c7x0_write32 (DSP_REG, start);
- if (hostdata->options & OPTION_DEBUG_TRACE)
- NCR53c7x0_write8 (DCNTL_REG, hostdata->saved_dcntl |
- DCNTL_SSM | DCNTL_STD);
- local_irq_restore(flags);
-
- timeout = jiffies + 5 * HZ; /* arbitrary */
- while ((hostdata->test_completed == -1) && time_before(jiffies, timeout))
- barrier();
-
- NCR53c7x0_write32 (DSA_REG, 0);
-
- if (hostdata->test_completed == 2) {
- data[35] = 0;
- printk ("scsi%d : test 2 INQUIRY to target %d, lun 0 : %s\n",
- host->host_no, i, data + 8);
- printk ("scsi%d : status ", host->host_no);
- scsi_print_status (status);
- printk ("\nscsi%d : message ", host->host_no);
- spi_print_msg(&msg);
- printk ("\n");
- } else if (hostdata->test_completed == 3) {
- printk("scsi%d : test 2 no connection with target %d\n",
- host->host_no, i);
- if (!hostdata->idle) {
- printk("scsi%d : not idle\n", host->host_no);
- local_irq_restore(flags);
- return -1;
- }
- } else if (hostdata->test_completed == -1) {
- printk ("scsi%d : test 2 timed out\n", host->host_no);
- local_irq_restore(flags);
- return -1;
- }
- hostdata->test_running = 0;
- }
- }
-
- local_irq_restore(flags);
- return 0;
-}
-
-/*
- * Function : static void NCR53c7xx_dsa_fixup (struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : copy the NCR53c8xx dsa structure into cmd's dsa buffer,
- * performing all necessary relocation.
- *
- * Inputs : cmd, a NCR53c7x0_cmd structure with a dsa area large
- * enough to hold the NCR53c8xx dsa.
- */
-
-static void
-NCR53c7xx_dsa_fixup (struct NCR53c7x0_cmd *cmd) {
- Scsi_Cmnd *c = cmd->cmd;
- struct Scsi_Host *host = c->device->host;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- int i;
-
- memcpy (cmd->dsa, hostdata->script + (hostdata->E_dsa_code_template / 4),
- hostdata->E_dsa_code_template_end - hostdata->E_dsa_code_template);
-
- /*
- * Note : within the NCR 'C' code, dsa points to the _start_
- * of the DSA structure, and _not_ the offset of dsa_zero within
- * that structure used to facilitate shorter signed offsets
- * for the 8 bit ALU.
- *
- * The implications of this are that
- *
- * - 32 bit A_dsa_* absolute values require an additional
- * dsa_zero added to their value to be correct, since they are
- * relative to dsa_zero which is in essentially a separate
- * space from the code symbols.
- *
- * - All other symbols require no special treatment.
- */
-
- patch_abs_tci_data (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_lun, c->device->lun);
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_addr_next, virt_to_bus(&cmd->dsa_next_addr));
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_next, virt_to_bus(cmd->dsa) + Ent_dsa_zero -
- Ent_dsa_code_template + A_dsa_next);
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_sync, virt_to_bus((void *)hostdata->sync[c->device->id].script));
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_sscf_710, virt_to_bus((void *)&hostdata->sync[c->device->id].sscf_710));
- patch_abs_tci_data (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_target, 1 << c->device->id);
- /* XXX - new pointer stuff */
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_addr_saved_pointer, virt_to_bus(&cmd->saved_data_pointer));
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_addr_saved_residual, virt_to_bus(&cmd->saved_residual));
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_addr_residual, virt_to_bus(&cmd->residual));
-
- /* XXX - new start stuff */
-
- patch_abs_32 (cmd->dsa, Ent_dsa_code_template / sizeof(u32),
- dsa_temp_addr_dsa_value, virt_to_bus(&cmd->dsa_addr));
-}
-
-/*
- * Function : run_process_issue_queue (void)
- *
- * Purpose : insure that the coroutine is running and will process our
- * request. process_issue_queue_running is checked/set here (in an
- * inline function) rather than in process_issue_queue itself to reduce
- * the chances of stack overflow.
- *
- */
-
-static volatile int process_issue_queue_running = 0;
-
-static __inline__ void
-run_process_issue_queue(void) {
- unsigned long flags;
- local_irq_save(flags);
- if (!process_issue_queue_running) {
- process_issue_queue_running = 1;
- process_issue_queue(flags);
- /*
- * process_issue_queue_running is cleared in process_issue_queue
- * once it can't do more work, and process_issue_queue exits with
- * interrupts disabled.
- */
- }
- local_irq_restore(flags);
-}
-
-/*
- * Function : static void abnormal_finished (struct NCR53c7x0_cmd *cmd, int
- * result)
- *
- * Purpose : mark SCSI command as finished, OR'ing the host portion
- * of the result word into the result field of the corresponding
- * Scsi_Cmnd structure, and removing it from the internal queues.
- *
- * Inputs : cmd - command, result - entire result field
- *
- * Preconditions : the NCR chip should be in a halted state when
- * abnormal_finished is run, since it modifies structures which
- * the NCR expects to have exclusive access to.
- */
-
-static void
-abnormal_finished (struct NCR53c7x0_cmd *cmd, int result) {
- Scsi_Cmnd *c = cmd->cmd;
- struct Scsi_Host *host = c->device->host;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned long flags;
- int left, found;
- volatile struct NCR53c7x0_cmd * linux_search;
- volatile struct NCR53c7x0_cmd * volatile *linux_prev;
- volatile u32 *ncr_prev, *ncrcurrent, ncr_search;
-
-#if 0
- printk ("scsi%d: abnormal finished\n", host->host_no);
-#endif
-
- local_irq_save(flags);
- found = 0;
- /*
- * Traverse the NCR issue array until we find a match or run out
- * of instructions. Instructions in the NCR issue array are
- * either JUMP or NOP instructions, which are 2 words in length.
- */
-
-
- for (found = 0, left = host->can_queue, ncrcurrent = hostdata->schedule;
- left > 0; --left, ncrcurrent += 2)
- {
- if (issue_to_cmd (host, hostdata, (u32 *) ncrcurrent) == cmd)
- {
- ncrcurrent[0] = hostdata->NOP_insn;
- ncrcurrent[1] = 0xdeadbeef;
- ++found;
- break;
- }
- }
-
- /*
- * Traverse the NCR reconnect list of DSA structures until we find
- * a pointer to this dsa or have found too many command structures.
- * We let prev point at the next field of the previous element or
- * head of the list, so we don't do anything different for removing
- * the head element.
- */
-
- for (left = host->can_queue,
- ncr_search = hostdata->reconnect_dsa_head,
- ncr_prev = &hostdata->reconnect_dsa_head;
- left >= 0 && ncr_search &&
- ((char*)bus_to_virt(ncr_search) + hostdata->dsa_start)
- != (char *) cmd->dsa;
- ncr_prev = (u32*) ((char*)bus_to_virt(ncr_search) +
- hostdata->dsa_next), ncr_search = *ncr_prev, --left);
-
- if (left < 0)
- printk("scsi%d: loop detected in ncr reconncect list\n",
- host->host_no);
- else if (ncr_search) {
- if (found)
- printk("scsi%d: scsi %ld in ncr issue array and reconnect lists\n",
- host->host_no, c->pid);
- else {
- volatile u32 * next = (u32 *)
- ((char *)bus_to_virt(ncr_search) + hostdata->dsa_next);
- *ncr_prev = *next;
-/* If we're at the tail end of the issue queue, update that pointer too. */
- found = 1;
- }
- }
-
- /*
- * Traverse the host running list until we find this command or discover
- * we have too many elements, pointing linux_prev at the next field of the
- * linux_previous element or head of the list, search at this element.
- */
-
- for (left = host->can_queue, linux_search = hostdata->running_list,
- linux_prev = &hostdata->running_list;
- left >= 0 && linux_search && linux_search != cmd;
- linux_prev = &(linux_search->next),
- linux_search = linux_search->next, --left);
-
- if (left < 0)
- printk ("scsi%d: loop detected in host running list for scsi pid %ld\n",
- host->host_no, c->pid);
- else if (linux_search) {
- *linux_prev = linux_search->next;
- --hostdata->busy[c->device->id][c->device->lun];
- }
-
- /* Return the NCR command structure to the free list */
- cmd->next = hostdata->free;
- hostdata->free = cmd;
- c->host_scribble = NULL;
-
- /* And return */
- c->result = result;
- c->scsi_done(c);
-
- local_irq_restore(flags);
- run_process_issue_queue();
-}
-
-/*
- * Function : static void intr_break (struct Scsi_Host *host,
- * struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : Handler for breakpoint interrupts from a SCSI script
- *
- * Inputs : host - pointer to this host adapter's structure,
- * cmd - pointer to the command (if any) dsa was pointing
- * to.
- *
- */
-
-static void
-intr_break (struct Scsi_Host *host, struct
- NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_break *bp;
-#if 0
- Scsi_Cmnd *c = cmd ? cmd->cmd : NULL;
-#endif
- u32 *dsp;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned long flags;
- NCR53c7x0_local_setup(host);
-
- /*
- * Find the break point corresponding to this address, and
- * dump the appropriate debugging information to standard
- * output.
- */
- local_irq_save(flags);
- dsp = (u32 *) bus_to_virt(NCR53c7x0_read32(DSP_REG));
- for (bp = hostdata->breakpoints; bp && bp->address != dsp;
- bp = bp->next);
- if (!bp)
- panic("scsi%d : break point interrupt from %p with no breakpoint!",
- host->host_no, dsp);
-
- /*
- * Configure the NCR chip for manual start mode, so that we can
- * point the DSP register at the instruction that follows the
- * INT int_debug_break instruction.
- */
-
- NCR53c7x0_write8 (hostdata->dmode,
- NCR53c7x0_read8(hostdata->dmode)|DMODE_MAN);
-
- /*
- * And update the DSP register, using the size of the old
- * instruction in bytes.
- */
-
- local_irq_restore(flags);
-}
-/*
- * Function : static void print_synchronous (const char *prefix,
- * const unsigned char *msg)
- *
- * Purpose : print a pretty, user and machine parsable representation
- * of a SDTR message, including the "real" parameters, data
- * clock so we can tell transfer rate at a glance.
- *
- * Inputs ; prefix - text to prepend, msg - SDTR message (5 bytes)
- */
-
-static void
-print_synchronous (const char *prefix, const unsigned char *msg) {
- if (msg[4]) {
- int Hz = 1000000000 / (msg[3] * 4);
- int integer = Hz / 1000000;
- int fraction = (Hz - (integer * 1000000)) / 10000;
- printk ("%speriod %dns offset %d %d.%02dMHz %s SCSI%s\n",
- prefix, (int) msg[3] * 4, (int) msg[4], integer, fraction,
- (((msg[3] * 4) < 200) ? "FAST" : "synchronous"),
- (((msg[3] * 4) < 200) ? "-II" : ""));
- } else
- printk ("%sasynchronous SCSI\n", prefix);
-}
-
-/*
- * Function : static void set_synchronous (struct Scsi_Host *host,
- * int target, int sxfer, int scntl3, int now_connected)
- *
- * Purpose : reprogram transfers between the selected SCSI initiator and
- * target with the given register values; in the indirect
- * select operand, reselection script, and chip registers.
- *
- * Inputs : host - NCR53c7,8xx SCSI host, target - number SCSI target id,
- * sxfer and scntl3 - NCR registers. now_connected - if non-zero,
- * we should reprogram the registers now too.
- *
- * NOTE: For 53c710, scntl3 is actually used for SCF bits from
- * SBCL, as we don't have a SCNTL3.
- */
-
-static void
-set_synchronous (struct Scsi_Host *host, int target, int sxfer, int scntl3,
- int now_connected) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- u32 *script;
- NCR53c7x0_local_setup(host);
-
- /* These are eight bit registers */
- sxfer &= 0xff;
- scntl3 &= 0xff;
-
- hostdata->sync[target].sxfer_sanity = sxfer;
- hostdata->sync[target].scntl3_sanity = scntl3;
-
-/*
- * HARD CODED : synchronous script is EIGHT words long. This
- * must agree with 53c7.8xx.h
- */
-
- if ((hostdata->chip != 700) && (hostdata->chip != 70066)) {
- hostdata->sync[target].select_indirect = (1 << target) << 16 |
- (sxfer << 8);
- hostdata->sync[target].sscf_710 = scntl3;
-
- script = (u32 *) hostdata->sync[target].script;
-
- /* XXX - add NCR53c7x0 code to reprogram SCF bits if we want to */
- script[0] = ((DCMD_TYPE_RWRI | DCMD_RWRI_OPC_MODIFY |
- DCMD_RWRI_OP_MOVE) << 24) |
- (SBCL_REG << 16) | (scntl3 << 8);
- script[1] = 0;
- script += 2;
-
- script[0] = ((DCMD_TYPE_RWRI | DCMD_RWRI_OPC_MODIFY |
- DCMD_RWRI_OP_MOVE) << 24) |
- (SXFER_REG << 16) | (sxfer << 8);
- script[1] = 0;
- script += 2;
-
-#ifdef DEBUG_SYNC_INTR
- if (hostdata->options & OPTION_DEBUG_DISCONNECT) {
- script[0] = ((DCMD_TYPE_TCI|DCMD_TCI_OP_INT) << 24) | DBC_TCI_TRUE;
- script[1] = DEBUG_SYNC_INTR;
- script += 2;
- }
-#endif
-
- script[0] = ((DCMD_TYPE_TCI|DCMD_TCI_OP_RETURN) << 24) | DBC_TCI_TRUE;
- script[1] = 0;
- script += 2;
- }
-
- if (hostdata->options & OPTION_DEBUG_SYNCHRONOUS)
- printk ("scsi%d : target %d sync parameters are sxfer=0x%x, scntl3=0x%x\n",
- host->host_no, target, sxfer, scntl3);
-
- if (now_connected) {
- NCR53c7x0_write8(SBCL_REG, scntl3);
- NCR53c7x0_write8(SXFER_REG, sxfer);
- }
-}
-
-
-/*
- * Function : static int asynchronous (struct Scsi_Host *host, int target)
- *
- * Purpose : reprogram between the selected SCSI Host adapter and target
- * (assumed to be currently connected) for asynchronous transfers.
- *
- * Inputs : host - SCSI host structure, target - numeric target ID.
- *
- * Preconditions : the NCR chip should be in one of the halted states
- */
-
-static void
-asynchronous (struct Scsi_Host *host, int target) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- NCR53c7x0_local_setup(host);
- set_synchronous (host, target, /* no offset */ 0, hostdata->saved_scntl3,
- 1);
- printk ("scsi%d : setting target %d to asynchronous SCSI\n",
- host->host_no, target);
-}
-
-/*
- * XXX - do we want to go out of our way (ie, add extra code to selection
- * in the NCR53c710/NCR53c720 script) to reprogram the synchronous
- * conversion bits, or can we be content in just setting the
- * sxfer bits? I chose to do so [richard@sleepie.demon.co.uk]
- */
-
-/* Table for NCR53c8xx synchronous values */
-
-/* This table is also correct for 710, allowing that scf=4 is equivalent
- * of SSCF=0 (ie use DCNTL, divide by 3) for a 50.01-66.00MHz clock.
- * For any other clock values, we cannot use entries with SCF values of
- * 4. I guess that for a 66MHz clock, the slowest it will set is 2MHz,
- * and for a 50MHz clock, the slowest will be 2.27Mhz. Should check
- * that a device doesn't try and negotiate sync below these limits!
- */
-
-static const struct {
- int div; /* Total clock divisor * 10 */
- unsigned char scf; /* */
- unsigned char tp; /* 4 + tp = xferp divisor */
-} syncs[] = {
-/* div scf tp div scf tp div scf tp */
- { 40, 1, 0}, { 50, 1, 1}, { 60, 1, 2},
- { 70, 1, 3}, { 75, 2, 1}, { 80, 1, 4},
- { 90, 1, 5}, { 100, 1, 6}, { 105, 2, 3},
- { 110, 1, 7}, { 120, 2, 4}, { 135, 2, 5},
- { 140, 3, 3}, { 150, 2, 6}, { 160, 3, 4},
- { 165, 2, 7}, { 180, 3, 5}, { 200, 3, 6},
- { 210, 4, 3}, { 220, 3, 7}, { 240, 4, 4},
- { 270, 4, 5}, { 300, 4, 6}, { 330, 4, 7}
-};
-
-/*
- * Function : static void synchronous (struct Scsi_Host *host, int target,
- * char *msg)
- *
- * Purpose : reprogram transfers between the selected SCSI initiator and
- * target for synchronous SCSI transfers such that the synchronous
- * offset is less than that requested and period at least as long
- * as that requested. Also modify *msg such that it contains
- * an appropriate response.
- *
- * Inputs : host - NCR53c7,8xx SCSI host, target - number SCSI target id,
- * msg - synchronous transfer request.
- */
-
-
-static void
-synchronous (struct Scsi_Host *host, int target, char *msg) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- int desire, divisor, i, limit;
- unsigned char scntl3, sxfer;
-/* The diagnostic message fits on one line, even with max. width integers */
- char buf[80];
-
-/* Desired transfer clock in Hz */
- desire = 1000000000L / (msg[3] * 4);
-/* Scale the available SCSI clock by 10 so we get tenths */
- divisor = (hostdata->scsi_clock * 10) / desire;
-
-/* NCR chips can handle at most an offset of 8 */
- if (msg[4] > 8)
- msg[4] = 8;
-
- if (hostdata->options & OPTION_DEBUG_SDTR)
- printk("scsi%d : optimal synchronous divisor of %d.%01d\n",
- host->host_no, divisor / 10, divisor % 10);
-
- limit = ARRAY_SIZE(syncs) - 1;
- for (i = 0; (i < limit) && (divisor > syncs[i].div); ++i);
-
- if (hostdata->options & OPTION_DEBUG_SDTR)
- printk("scsi%d : selected synchronous divisor of %d.%01d\n",
- host->host_no, syncs[i].div / 10, syncs[i].div % 10);
-
- msg[3] = ((1000000000L / hostdata->scsi_clock) * syncs[i].div / 10 / 4);
-
- if (hostdata->options & OPTION_DEBUG_SDTR)
- printk("scsi%d : selected synchronous period of %dns\n", host->host_no,
- msg[3] * 4);
-
- scntl3 = syncs[i].scf;
- sxfer = (msg[4] << SXFER_MO_SHIFT) | (syncs[i].tp << 4);
- if (hostdata->options & OPTION_DEBUG_SDTR)
- printk ("scsi%d : sxfer=0x%x scntl3=0x%x\n",
- host->host_no, (int) sxfer, (int) scntl3);
- set_synchronous (host, target, sxfer, scntl3, 1);
- sprintf (buf, "scsi%d : setting target %d to ", host->host_no, target);
- print_synchronous (buf, msg);
-}
-
-/*
- * Function : static int NCR53c7x0_dstat_sir_intr (struct Scsi_Host *host,
- * struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : Handler for INT generated instructions for the
- * NCR53c810/820 SCSI SCRIPT
- *
- * Inputs : host - pointer to this host adapter's structure,
- * cmd - pointer to the command (if any) dsa was pointing
- * to.
- *
- */
-
-static int
-NCR53c7x0_dstat_sir_intr (struct Scsi_Host *host, struct
- NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- int print;
- Scsi_Cmnd *c = cmd ? cmd->cmd : NULL;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- u32 dsps,*dsp; /* Argument of the INT instruction */
-
- NCR53c7x0_local_setup(host);
- dsps = NCR53c7x0_read32(DSPS_REG);
- dsp = (u32 *) bus_to_virt(NCR53c7x0_read32(DSP_REG));
-
- /* RGH 150597: Frig. Commands which fail with Check Condition are
- * Flagged as successful - hack dsps to indicate check condition */
-#if 0
- /* RGH 200597: Need to disable for BVME6000, as it gets Check Conditions
- * and then dies. Seems to handle Check Condition at startup, but
- * not mid kernel build. */
- if (dsps == A_int_norm_emulateintfly && cmd && cmd->result == 2)
- dsps = A_int_err_check_condition;
-#endif
-
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : DSPS = 0x%x\n", host->host_no, dsps);
-
- switch (dsps) {
- case A_int_msg_1:
- print = 1;
- switch (hostdata->msg_buf[0]) {
- /*
- * Unless we've initiated synchronous negotiation, I don't
- * think that this should happen.
- */
- case MESSAGE_REJECT:
- hostdata->dsp = hostdata->script + hostdata->E_accept_message /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- if (cmd && (cmd->flags & CMD_FLAG_SDTR)) {
- printk ("scsi%d : target %d rejected SDTR\n", host->host_no,
- c->device->id);
- cmd->flags &= ~CMD_FLAG_SDTR;
- asynchronous (host, c->device->id);
- print = 0;
- }
- break;
- case INITIATE_RECOVERY:
- printk ("scsi%d : extended contingent allegiance not supported yet, rejecting\n",
- host->host_no);
- /* Fall through to default */
- hostdata->dsp = hostdata->script + hostdata->E_reject_message /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- break;
- default:
- printk ("scsi%d : unsupported message, rejecting\n",
- host->host_no);
- hostdata->dsp = hostdata->script + hostdata->E_reject_message /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- }
- if (print) {
- printk ("scsi%d : received message", host->host_no);
- if (c)
- printk (" from target %d lun %d ", c->device->id, c->device->lun);
- spi_print_msg((unsigned char *) hostdata->msg_buf);
- printk("\n");
- }
-
- return SPECIFIC_INT_NOTHING;
-
-
- case A_int_msg_sdtr:
-/*
- * At this point, hostdata->msg_buf contains
- * 0 EXTENDED MESSAGE
- * 1 length
- * 2 SDTR
- * 3 period * 4ns
- * 4 offset
- */
-
- if (cmd) {
- char buf[80];
- sprintf (buf, "scsi%d : target %d %s ", host->host_no, c->device->id,
- (cmd->flags & CMD_FLAG_SDTR) ? "accepting" : "requesting");
- print_synchronous (buf, (unsigned char *) hostdata->msg_buf);
-
- /*
- * Initiator initiated, won't happen unless synchronous
- * transfers are enabled. If we get a SDTR message in
- * response to our SDTR, we should program our parameters
- * such that
- * offset <= requested offset
- * period >= requested period
- */
- if (cmd->flags & CMD_FLAG_SDTR) {
- cmd->flags &= ~CMD_FLAG_SDTR;
- if (hostdata->msg_buf[4])
- synchronous (host, c->device->id, (unsigned char *)
- hostdata->msg_buf);
- else
- asynchronous (host, c->device->id);
- hostdata->dsp = hostdata->script + hostdata->E_accept_message /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- return SPECIFIC_INT_NOTHING;
- } else {
- if (hostdata->options & OPTION_SYNCHRONOUS) {
- cmd->flags |= CMD_FLAG_DID_SDTR;
- synchronous (host, c->device->id, (unsigned char *)
- hostdata->msg_buf);
- } else {
- hostdata->msg_buf[4] = 0; /* 0 offset = async */
- asynchronous (host, c->device->id);
- }
- patch_dsa_32 (cmd->dsa, dsa_msgout_other, 0, 5);
- patch_dsa_32 (cmd->dsa, dsa_msgout_other, 1, (u32)
- virt_to_bus ((void *)&hostdata->msg_buf));
- hostdata->dsp = hostdata->script +
- hostdata->E_respond_message / sizeof(u32);
- hostdata->dsp_changed = 1;
- }
- return SPECIFIC_INT_NOTHING;
- }
- /* Fall through to abort if we couldn't find a cmd, and
- therefore a dsa structure to twiddle */
- case A_int_msg_wdtr:
- hostdata->dsp = hostdata->script + hostdata->E_reject_message /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- return SPECIFIC_INT_NOTHING;
- case A_int_err_unexpected_phase:
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : unexpected phase\n", host->host_no);
- return SPECIFIC_INT_ABORT;
- case A_int_err_selected:
- if ((hostdata->chip / 100) == 8)
- printk ("scsi%d : selected by target %d\n", host->host_no,
- (int) NCR53c7x0_read8(SDID_REG_800) &7);
- else
- printk ("scsi%d : selected by target LCRC=0x%02x\n", host->host_no,
- (int) NCR53c7x0_read8(LCRC_REG_10));
- hostdata->dsp = hostdata->script + hostdata->E_target_abort /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- return SPECIFIC_INT_NOTHING;
- case A_int_err_unexpected_reselect:
- if ((hostdata->chip / 100) == 8)
- printk ("scsi%d : unexpected reselect by target %d lun %d\n",
- host->host_no, (int) NCR53c7x0_read8(SDID_REG_800) & 7,
- hostdata->reselected_identify & 7);
- else
- printk ("scsi%d : unexpected reselect LCRC=0x%02x\n", host->host_no,
- (int) NCR53c7x0_read8(LCRC_REG_10));
- hostdata->dsp = hostdata->script + hostdata->E_initiator_abort /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- return SPECIFIC_INT_NOTHING;
-/*
- * Since contingent allegiance conditions are cleared by the next
- * command issued to a target, we must issue a REQUEST SENSE
- * command after receiving a CHECK CONDITION status, before
- * another command is issued.
- *
- * Since this NCR53c7x0_cmd will be freed after use, we don't
- * care if we step on the various fields, so modify a few things.
- */
- case A_int_err_check_condition:
-#if 0
- if (hostdata->options & OPTION_DEBUG_INTR)
-#endif
- printk ("scsi%d : CHECK CONDITION\n", host->host_no);
- if (!c) {
- printk("scsi%d : CHECK CONDITION with no SCSI command\n",
- host->host_no);
- return SPECIFIC_INT_PANIC;
- }
-
- /*
- * FIXME : this uses the normal one-byte selection message.
- * We may want to renegotiate for synchronous & WIDE transfers
- * since these could be the crux of our problem.
- *
- hostdata->NOP_insn* FIXME : once SCSI-II tagged queuing is implemented, we'll
- * have to set this up so that the rest of the DSA
- * agrees with this being an untagged queue'd command.
- */
-
- patch_dsa_32 (cmd->dsa, dsa_msgout, 0, 1);
-
- /*
- * Modify the table indirect for COMMAND OUT phase, since
- * Request Sense is a six byte command.
- */
-
- patch_dsa_32 (cmd->dsa, dsa_cmdout, 0, 6);
-
- /*
- * The CDB is now mirrored in our local non-cached
- * structure, but keep the old structure up to date as well,
- * just in case anyone looks at it.
- */
-
- /*
- * XXX Need to worry about data buffer alignment/cache state
- * XXX here, but currently never get A_int_err_check_condition,
- * XXX so ignore problem for now.
- */
- cmd->cmnd[0] = c->cmnd[0] = REQUEST_SENSE;
- cmd->cmnd[0] = c->cmnd[1] &= 0xe0; /* Zero all but LUN */
- cmd->cmnd[0] = c->cmnd[2] = 0;
- cmd->cmnd[0] = c->cmnd[3] = 0;
- cmd->cmnd[0] = c->cmnd[4] = sizeof(c->sense_buffer);
- cmd->cmnd[0] = c->cmnd[5] = 0;
-
- /*
- * Disable dataout phase, and program datain to transfer to the
- * sense buffer, and add a jump to other_transfer after the
- * command so overflow/underrun conditions are detected.
- */
-
- patch_dsa_32 (cmd->dsa, dsa_dataout, 0,
- virt_to_bus(hostdata->script) + hostdata->E_other_transfer);
- patch_dsa_32 (cmd->dsa, dsa_datain, 0,
- virt_to_bus(cmd->data_transfer_start));
- cmd->data_transfer_start[0] = (((DCMD_TYPE_BMI | DCMD_BMI_OP_MOVE_I |
- DCMD_BMI_IO)) << 24) | sizeof(c->sense_buffer);
- cmd->data_transfer_start[1] = (u32) virt_to_bus(c->sense_buffer);
-
- cmd->data_transfer_start[2] = ((DCMD_TYPE_TCI | DCMD_TCI_OP_JUMP)
- << 24) | DBC_TCI_TRUE;
- cmd->data_transfer_start[3] = (u32) virt_to_bus(hostdata->script) +
- hostdata->E_other_transfer;
-
- /*
- * Currently, this command is flagged as completed, ie
- * it has valid status and message data. Reflag it as
- * incomplete. Q - need to do something so that original
- * status, etc are used.
- */
-
- cmd->result = cmd->cmd->result = 0xffff;
-
- /*
- * Restart command as a REQUEST SENSE.
- */
- hostdata->dsp = (u32 *) hostdata->script + hostdata->E_select /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- return SPECIFIC_INT_NOTHING;
- case A_int_debug_break:
- return SPECIFIC_INT_BREAK;
- case A_int_norm_aborted:
- hostdata->dsp = (u32 *) hostdata->schedule;
- hostdata->dsp_changed = 1;
- if (cmd)
- abnormal_finished (cmd, DID_ERROR << 16);
- return SPECIFIC_INT_NOTHING;
- case A_int_norm_emulateintfly:
- NCR53c7x0_intfly(host);
- return SPECIFIC_INT_NOTHING;
- case A_int_test_1:
- case A_int_test_2:
- hostdata->idle = 1;
- hostdata->test_completed = (dsps - A_int_test_1) / 0x00010000 + 1;
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk("scsi%d : test%d complete\n", host->host_no,
- hostdata->test_completed);
- return SPECIFIC_INT_NOTHING;
-#ifdef A_int_debug_reselected_ok
- case A_int_debug_reselected_ok:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT)) {
- /*
- * Note - this dsa is not based on location relative to
- * the command structure, but to location relative to the
- * DSA register
- */
- u32 *dsa;
- dsa = (u32 *) bus_to_virt (NCR53c7x0_read32(DSA_REG));
-
- printk("scsi%d : reselected_ok (DSA = 0x%x (virt 0x%p)\n",
- host->host_no, NCR53c7x0_read32(DSA_REG), dsa);
- printk("scsi%d : resume address is 0x%x (virt 0x%p)\n",
- host->host_no, cmd->saved_data_pointer,
- bus_to_virt(cmd->saved_data_pointer));
- print_insn (host, hostdata->script + Ent_reselected_ok /
- sizeof(u32), "", 1);
- if ((hostdata->chip / 100) == 8)
- printk ("scsi%d : sxfer=0x%x, scntl3=0x%x\n",
- host->host_no, NCR53c7x0_read8(SXFER_REG),
- NCR53c7x0_read8(SCNTL3_REG_800));
- else
- printk ("scsi%d : sxfer=0x%x, cannot read SBCL\n",
- host->host_no, NCR53c7x0_read8(SXFER_REG));
- if (c) {
- print_insn (host, (u32 *)
- hostdata->sync[c->device->id].script, "", 1);
- print_insn (host, (u32 *)
- hostdata->sync[c->device->id].script + 2, "", 1);
- }
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_reselect_check
- case A_int_debug_reselect_check:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- u32 *dsa;
-#if 0
- u32 *code;
-#endif
- /*
- * Note - this dsa is not based on location relative to
- * the command structure, but to location relative to the
- * DSA register
- */
- dsa = bus_to_virt (NCR53c7x0_read32(DSA_REG));
- printk("scsi%d : reselected_check_next (DSA = 0x%lx (virt 0x%p))\n",
- host->host_no, virt_to_bus(dsa), dsa);
- if (dsa) {
- printk("scsi%d : resume address is 0x%x (virt 0x%p)\n",
- host->host_no, cmd->saved_data_pointer,
- bus_to_virt (cmd->saved_data_pointer));
-#if 0
- printk("scsi%d : template code :\n", host->host_no);
- for (code = dsa + (Ent_dsa_code_check_reselect - Ent_dsa_zero)
- / sizeof(u32); code < (dsa + Ent_dsa_zero / sizeof(u32));
- code += print_insn (host, code, "", 1));
-#endif
- }
- print_insn (host, hostdata->script + Ent_reselected_ok /
- sizeof(u32), "", 1);
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_dsa_schedule
- case A_int_debug_dsa_schedule:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- u32 *dsa;
- /*
- * Note - this dsa is not based on location relative to
- * the command structure, but to location relative to the
- * DSA register
- */
- dsa = (u32 *) bus_to_virt (NCR53c7x0_read32(DSA_REG));
- printk("scsi%d : dsa_schedule (old DSA = 0x%lx (virt 0x%p))\n",
- host->host_no, virt_to_bus(dsa), dsa);
- if (dsa)
- printk("scsi%d : resume address is 0x%x (virt 0x%p)\n"
- " (temp was 0x%x (virt 0x%p))\n",
- host->host_no, cmd->saved_data_pointer,
- bus_to_virt (cmd->saved_data_pointer),
- NCR53c7x0_read32 (TEMP_REG),
- bus_to_virt (NCR53c7x0_read32(TEMP_REG)));
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_scheduled
- case A_int_debug_scheduled:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- printk("scsi%d : new I/O 0x%x (virt 0x%p) scheduled\n",
- host->host_no, NCR53c7x0_read32(DSA_REG),
- bus_to_virt(NCR53c7x0_read32(DSA_REG)));
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_idle
- case A_int_debug_idle:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- printk("scsi%d : idle\n", host->host_no);
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_cmd
- case A_int_debug_cmd:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- printk("scsi%d : command sent\n");
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_dsa_loaded
- case A_int_debug_dsa_loaded:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- printk("scsi%d : DSA loaded with 0x%x (virt 0x%p)\n", host->host_no,
- NCR53c7x0_read32(DSA_REG),
- bus_to_virt(NCR53c7x0_read32(DSA_REG)));
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_reselected
- case A_int_debug_reselected:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT)) {
- if ((hostdata->chip / 100) == 8)
- printk("scsi%d : reselected by target %d lun %d\n",
- host->host_no, (int) NCR53c7x0_read8(SDID_REG_800) & ~0x80,
- (int) hostdata->reselected_identify & 7);
- else
- printk("scsi%d : reselected by LCRC=0x%02x lun %d\n",
- host->host_no, (int) NCR53c7x0_read8(LCRC_REG_10),
- (int) hostdata->reselected_identify & 7);
- print_queues(host);
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_disconnect_msg
- case A_int_debug_disconnect_msg:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR)) {
- if (c)
- printk("scsi%d : target %d lun %d disconnecting\n",
- host->host_no, c->device->id, c->device->lun);
- else
- printk("scsi%d : unknown target disconnecting\n",
- host->host_no);
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_disconnected
- case A_int_debug_disconnected:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT)) {
- printk ("scsi%d : disconnected, new queues are\n",
- host->host_no);
- print_queues(host);
-#if 0
- /* Not valid on ncr53c710! */
- printk ("scsi%d : sxfer=0x%x, scntl3=0x%x\n",
- host->host_no, NCR53c7x0_read8(SXFER_REG),
- NCR53c7x0_read8(SCNTL3_REG_800));
-#endif
- if (c) {
- print_insn (host, (u32 *)
- hostdata->sync[c->device->id].script, "", 1);
- print_insn (host, (u32 *)
- hostdata->sync[c->device->id].script + 2, "", 1);
- }
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_panic
- case A_int_debug_panic:
- printk("scsi%d : int_debug_panic received\n", host->host_no);
- print_lots (host);
- return SPECIFIC_INT_PANIC;
-#endif
-#ifdef A_int_debug_saved
- case A_int_debug_saved:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT)) {
- printk ("scsi%d : saved data pointer 0x%x (virt 0x%p)\n",
- host->host_no, cmd->saved_data_pointer,
- bus_to_virt (cmd->saved_data_pointer));
- print_progress (c);
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_restored
- case A_int_debug_restored:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT)) {
- if (cmd) {
- int size;
- printk ("scsi%d : restored data pointer 0x%x (virt 0x%p)\n",
- host->host_no, cmd->saved_data_pointer, bus_to_virt (
- cmd->saved_data_pointer));
- size = print_insn (host, (u32 *)
- bus_to_virt(cmd->saved_data_pointer), "", 1);
- size = print_insn (host, (u32 *)
- bus_to_virt(cmd->saved_data_pointer) + size, "", 1);
- print_progress (c);
- }
-#if 0
- printk ("scsi%d : datapath residual %d\n",
- host->host_no, datapath_residual (host)) ;
-#endif
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_sync
- case A_int_debug_sync:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT|OPTION_DEBUG_SDTR)) {
- unsigned char sxfer = NCR53c7x0_read8 (SXFER_REG), scntl3;
- if ((hostdata->chip / 100) == 8) {
- scntl3 = NCR53c7x0_read8 (SCNTL3_REG_800);
- if (c) {
- if (sxfer != hostdata->sync[c->device->id].sxfer_sanity ||
- scntl3 != hostdata->sync[c->device->id].scntl3_sanity) {
- printk ("scsi%d : sync sanity check failed sxfer=0x%x, scntl3=0x%x",
- host->host_no, sxfer, scntl3);
- NCR53c7x0_write8 (SXFER_REG, sxfer);
- NCR53c7x0_write8 (SCNTL3_REG_800, scntl3);
- }
- } else
- printk ("scsi%d : unknown command sxfer=0x%x, scntl3=0x%x\n",
- host->host_no, (int) sxfer, (int) scntl3);
- } else {
- if (c) {
- if (sxfer != hostdata->sync[c->device->id].sxfer_sanity) {
- printk ("scsi%d : sync sanity check failed sxfer=0x%x",
- host->host_no, sxfer);
- NCR53c7x0_write8 (SXFER_REG, sxfer);
- NCR53c7x0_write8 (SBCL_REG,
- hostdata->sync[c->device->id].sscf_710);
- }
- } else
- printk ("scsi%d : unknown command sxfer=0x%x\n",
- host->host_no, (int) sxfer);
- }
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_datain
- case A_int_debug_datain:
- if (hostdata->options & (OPTION_DEBUG_SCRIPT|OPTION_DEBUG_INTR|
- OPTION_DEBUG_DISCONNECT|OPTION_DEBUG_SDTR)) {
- int size;
- if ((hostdata->chip / 100) == 8)
- printk ("scsi%d : In do_datain (%s) sxfer=0x%x, scntl3=0x%x\n"
- " datapath residual=%d\n",
- host->host_no, sbcl_to_phase (NCR53c7x0_read8 (SBCL_REG)),
- (int) NCR53c7x0_read8(SXFER_REG),
- (int) NCR53c7x0_read8(SCNTL3_REG_800),
- datapath_residual (host)) ;
- else
- printk ("scsi%d : In do_datain (%s) sxfer=0x%x\n"
- " datapath residual=%d\n",
- host->host_no, sbcl_to_phase (NCR53c7x0_read8 (SBCL_REG)),
- (int) NCR53c7x0_read8(SXFER_REG),
- datapath_residual (host)) ;
- print_insn (host, dsp, "", 1);
- size = print_insn (host, (u32 *) bus_to_virt(dsp[1]), "", 1);
- print_insn (host, (u32 *) bus_to_virt(dsp[1]) + size, "", 1);
- }
- return SPECIFIC_INT_RESTART;
-#endif
-#ifdef A_int_debug_check_dsa
- case A_int_debug_check_dsa:
- if (NCR53c7x0_read8 (SCNTL1_REG) & SCNTL1_CON) {
- int sdid;
- int tmp;
- char *where;
- if (hostdata->chip / 100 == 8)
- sdid = NCR53c7x0_read8 (SDID_REG_800) & 15;
- else {
- tmp = NCR53c7x0_read8 (SDID_REG_700);
- if (!tmp)
- panic ("SDID_REG_700 = 0");
- tmp >>= 1;
- sdid = 0;
- while (tmp) {
- tmp >>= 1;
- sdid++;
- }
- }
- where = dsp - NCR53c7x0_insn_size(NCR53c7x0_read8
- (DCMD_REG)) == hostdata->script +
- Ent_select_check_dsa / sizeof(u32) ?
- "selection" : "reselection";
- if (c && sdid != c->device->id) {
- printk ("scsi%d : SDID target %d != DSA target %d at %s\n",
- host->host_no, sdid, c->device->id, where);
- print_lots(host);
- dump_events (host, 20);
- return SPECIFIC_INT_PANIC;
- }
- }
- return SPECIFIC_INT_RESTART;
-#endif
- default:
- if ((dsps & 0xff000000) == 0x03000000) {
- printk ("scsi%d : misc debug interrupt 0x%x\n",
- host->host_no, dsps);
- return SPECIFIC_INT_RESTART;
- } else if ((dsps & 0xff000000) == 0x05000000) {
- if (hostdata->events) {
- struct NCR53c7x0_event *event;
- ++hostdata->event_index;
- if (hostdata->event_index >= hostdata->event_size)
- hostdata->event_index = 0;
- event = (struct NCR53c7x0_event *) hostdata->events +
- hostdata->event_index;
- event->event = (enum ncr_event) dsps;
- event->dsa = bus_to_virt(NCR53c7x0_read32(DSA_REG));
- if (NCR53c7x0_read8 (SCNTL1_REG) & SCNTL1_CON) {
- if (hostdata->chip / 100 == 8)
- event->target = NCR53c7x0_read8(SSID_REG_800);
- else {
- unsigned char tmp, sdid;
- tmp = NCR53c7x0_read8 (SDID_REG_700);
- if (!tmp)
- panic ("SDID_REG_700 = 0");
- tmp >>= 1;
- sdid = 0;
- while (tmp) {
- tmp >>= 1;
- sdid++;
- }
- event->target = sdid;
- }
- }
- else
- event->target = 255;
-
- if (event->event == EVENT_RESELECT)
- event->lun = hostdata->reselected_identify & 0xf;
- else if (c)
- event->lun = c->device->lun;
- else
- event->lun = 255;
- do_gettimeofday(&(event->time));
- if (c) {
- event->pid = c->pid;
- memcpy ((void *) event->cmnd, (void *) c->cmnd,
- sizeof (event->cmnd));
- } else {
- event->pid = -1;
- }
- }
- return SPECIFIC_INT_RESTART;
- }
-
- printk ("scsi%d : unknown user interrupt 0x%x\n",
- host->host_no, (unsigned) dsps);
- return SPECIFIC_INT_PANIC;
- }
-}
-
-/*
- * XXX - the stock NCR assembler won't output the scriptu.h file,
- * which undefine's all #define'd CPP symbols from the script.h
- * file, which will create problems if you use multiple scripts
- * with the same symbol names.
- *
- * If you insist on using NCR's assembler, you could generate
- * scriptu.h from script.h using something like
- *
- * grep #define script.h | \
- * sed 's/#define[ ][ ]*\([_a-zA-Z][_a-zA-Z0-9]*\).*$/#undefine \1/' \
- * > scriptu.h
- */
-
-#include "53c7xx_u.h"
-
-/* XXX - add alternate script handling code here */
-
-
-/*
- * Function : static void NCR537xx_soft_reset (struct Scsi_Host *host)
- *
- * Purpose : perform a soft reset of the NCR53c7xx chip
- *
- * Inputs : host - pointer to this host adapter's structure
- *
- * Preconditions : NCR53c7x0_init must have been called for this
- * host.
- *
- */
-
-static void
-NCR53c7x0_soft_reset (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- unsigned long flags;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- NCR53c7x0_local_setup(host);
-
- local_irq_save(flags);
-
- /* Disable scsi chip and s/w level 7 ints */
-
-#ifdef CONFIG_MVME16x
- if (MACH_IS_MVME16x)
- {
- volatile unsigned long v;
-
- v = *(volatile unsigned long *)0xfff4006c;
- v &= ~0x8000;
- *(volatile unsigned long *)0xfff4006c = v;
- v = *(volatile unsigned long *)0xfff4202c;
- v &= ~0x10;
- *(volatile unsigned long *)0xfff4202c = v;
- }
-#endif
- /* Anything specific for your hardware? */
-
- /*
- * Do a soft reset of the chip so that everything is
- * reinitialized to the power-on state.
- *
- * Basically follow the procedure outlined in the NCR53c700
- * data manual under Chapter Six, How to Use, Steps Necessary to
- * Start SCRIPTS, with the exception of actually starting the
- * script and setting up the synchronous transfer gunk.
- */
-
- /* Should we reset the scsi bus here??????????????????? */
-
- NCR53c7x0_write8(ISTAT_REG_700, ISTAT_10_SRST);
- NCR53c7x0_write8(ISTAT_REG_700, 0);
-
- /*
- * saved_dcntl is set up in NCR53c7x0_init() before it is overwritten
- * here. We should have some better way of working out the CF bit
- * setting..
- */
-
- hostdata->saved_dcntl = DCNTL_10_EA|DCNTL_10_COM;
- if (hostdata->scsi_clock > 50000000)
- hostdata->saved_dcntl |= DCNTL_700_CF_3;
- else
- if (hostdata->scsi_clock > 37500000)
- hostdata->saved_dcntl |= DCNTL_700_CF_2;
-#if 0
- else
- /* Any clocks less than 37.5MHz? */
-#endif
-
- if (hostdata->options & OPTION_DEBUG_TRACE)
- NCR53c7x0_write8(DCNTL_REG, hostdata->saved_dcntl | DCNTL_SSM);
- else
- NCR53c7x0_write8(DCNTL_REG, hostdata->saved_dcntl);
- /* Following disables snooping - snooping is not required, as non-
- * cached pages are used for shared data, and appropriate use is
- * made of cache_push/cache_clear. Indeed, for 68060
- * enabling snooping causes disk corruption of ext2fs free block
- * bitmaps and the like. If you have a 68060 with snooping hardwared
- * on, then you need to enable CONFIG_060_WRITETHROUGH.
- */
- NCR53c7x0_write8(CTEST7_REG, CTEST7_10_TT1|CTEST7_STD);
- /* Actually burst of eight, according to my 53c710 databook */
- NCR53c7x0_write8(hostdata->dmode, DMODE_10_BL_8 | DMODE_10_FC2);
- NCR53c7x0_write8(SCID_REG, 1 << host->this_id);
- NCR53c7x0_write8(SBCL_REG, 0);
- NCR53c7x0_write8(SCNTL1_REG, SCNTL1_ESR_700);
- NCR53c7x0_write8(SCNTL0_REG, ((hostdata->options & OPTION_PARITY) ?
- SCNTL0_EPC : 0) | SCNTL0_EPG_700 | SCNTL0_ARB1 | SCNTL0_ARB2);
-
- /*
- * Enable all interrupts, except parity which we only want when
- * the user requests it.
- */
-
- NCR53c7x0_write8(DIEN_REG, DIEN_700_BF |
- DIEN_ABRT | DIEN_SSI | DIEN_SIR | DIEN_700_OPC);
-
- NCR53c7x0_write8(SIEN_REG_700, ((hostdata->options & OPTION_PARITY) ?
- SIEN_PAR : 0) | SIEN_700_STO | SIEN_RST | SIEN_UDC |
- SIEN_SGE | SIEN_MA);
-
-#ifdef CONFIG_MVME16x
- if (MACH_IS_MVME16x)
- {
- volatile unsigned long v;
-
- /* Enable scsi chip and s/w level 7 ints */
- v = *(volatile unsigned long *)0xfff40080;
- v = (v & ~(0xf << 28)) | (4 << 28);
- *(volatile unsigned long *)0xfff40080 = v;
- v = *(volatile unsigned long *)0xfff4006c;
- v |= 0x8000;
- *(volatile unsigned long *)0xfff4006c = v;
- v = *(volatile unsigned long *)0xfff4202c;
- v = (v & ~0xff) | 0x10 | 4;
- *(volatile unsigned long *)0xfff4202c = v;
- }
-#endif
- /* Anything needed for your hardware? */
- local_irq_restore(flags);
-}
-
-
-/*
- * Function static struct NCR53c7x0_cmd *allocate_cmd (Scsi_Cmnd *cmd)
- *
- * Purpose : Return the first free NCR53c7x0_cmd structure (which are
- * reused in a LIFO manner to minimize cache thrashing).
- *
- * Side effects : If we haven't yet scheduled allocation of NCR53c7x0_cmd
- * structures for this device, do so. Attempt to complete all scheduled
- * allocations using get_zeroed_page(), putting NCR53c7x0_cmd structures on
- * the free list. Teach programmers not to drink and hack.
- *
- * Inputs : cmd - SCSI command
- *
- * Returns : NCR53c7x0_cmd structure allocated on behalf of cmd;
- * NULL on failure.
- */
-
-static void
-my_free_page (void *addr, int dummy)
-{
- /* XXX This assumes default cache mode to be IOMAP_FULL_CACHING, which
- * XXX may be invalid (CONFIG_060_WRITETHROUGH)
- */
- kernel_set_cachemode((void *)addr, 4096, IOMAP_FULL_CACHING);
- free_page ((u32)addr);
-}
-
-static struct NCR53c7x0_cmd *
-allocate_cmd (Scsi_Cmnd *cmd) {
- struct Scsi_Host *host = cmd->device->host;
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) host->hostdata[0];
- u32 real; /* Real address */
- int size; /* Size of *tmp */
- struct NCR53c7x0_cmd *tmp;
- unsigned long flags;
-
- if (hostdata->options & OPTION_DEBUG_ALLOCATION)
- printk ("scsi%d : num_cmds = %d, can_queue = %d\n"
- " target = %d, lun = %d, %s\n",
- host->host_no, hostdata->num_cmds, host->can_queue,
- cmd->device->id, cmd->device->lun, (hostdata->cmd_allocated[cmd->device->id] &
- (1 << cmd->device->lun)) ? "already allocated" : "not allocated");
-
-/*
- * If we have not yet reserved commands for this I_T_L nexus, and
- * the device exists (as indicated by permanent Scsi_Cmnd structures
- * being allocated under 1.3.x, or being outside of scan_scsis in
- * 1.2.x), do so now.
- */
- if (!(hostdata->cmd_allocated[cmd->device->id] & (1 << cmd->device->lun)) &&
- cmd->device && cmd->device->has_cmdblocks) {
- if ((hostdata->extra_allocate + hostdata->num_cmds) < host->can_queue)
- hostdata->extra_allocate += host->cmd_per_lun;
- hostdata->cmd_allocated[cmd->device->id] |= (1 << cmd->device->lun);
- }
-
- for (; hostdata->extra_allocate > 0 ; --hostdata->extra_allocate,
- ++hostdata->num_cmds) {
- /* historically, kmalloc has returned unaligned addresses; pad so we
- have enough room to ROUNDUP */
- size = hostdata->max_cmd_size + sizeof (void *);
-#ifdef FORCE_DSA_ALIGNMENT
- /*
- * 53c710 rev.0 doesn't have an add-with-carry instruction.
- * Ensure we allocate enough memory to force alignment.
- */
- size += 256;
-#endif
-/* FIXME: for ISA bus '7xx chips, we need to or GFP_DMA in here */
-
- if (size > 4096) {
- printk (KERN_ERR "53c7xx: allocate_cmd size > 4K\n");
- return NULL;
- }
- real = get_zeroed_page(GFP_ATOMIC);
- if (real == 0)
- return NULL;
- cache_push(virt_to_phys((void *)real), 4096);
- cache_clear(virt_to_phys((void *)real), 4096);
- kernel_set_cachemode((void *)real, 4096, IOMAP_NOCACHE_SER);
- tmp = ROUNDUP(real, void *);
-#ifdef FORCE_DSA_ALIGNMENT
- {
- if (((u32)tmp & 0xff) > CmdPageStart)
- tmp = (struct NCR53c7x0_cmd *)((u32)tmp + 255);
- tmp = (struct NCR53c7x0_cmd *)(((u32)tmp & ~0xff) + CmdPageStart);
-#if 0
- printk ("scsi: size = %d, real = 0x%08x, tmp set to 0x%08x\n",
- size, real, (u32)tmp);
-#endif
- }
-#endif
- tmp->real = (void *)real;
- tmp->size = size;
- tmp->free = ((void (*)(void *, int)) my_free_page);
- local_irq_save(flags);
- tmp->next = hostdata->free;
- hostdata->free = tmp;
- local_irq_restore(flags);
- }
- local_irq_save(flags);
- tmp = (struct NCR53c7x0_cmd *) hostdata->free;
- if (tmp) {
- hostdata->free = tmp->next;
- }
- local_irq_restore(flags);
- if (!tmp)
- printk ("scsi%d : can't allocate command for target %d lun %d\n",
- host->host_no, cmd->device->id, cmd->device->lun);
- return tmp;
-}
-
-/*
- * Function static struct NCR53c7x0_cmd *create_cmd (Scsi_Cmnd *cmd)
- *
- *
- * Purpose : allocate a NCR53c7x0_cmd structure, initialize it based on the
- * Scsi_Cmnd structure passed in cmd, including dsa and Linux field
- * initialization, and dsa code relocation.
- *
- * Inputs : cmd - SCSI command
- *
- * Returns : NCR53c7x0_cmd structure corresponding to cmd,
- * NULL on failure.
- */
-static struct NCR53c7x0_cmd *
-create_cmd (Scsi_Cmnd *cmd) {
- NCR53c7x0_local_declare();
- struct Scsi_Host *host = cmd->device->host;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- struct NCR53c7x0_cmd *tmp; /* NCR53c7x0_cmd structure for this command */
- int datain, /* Number of instructions per phase */
- dataout;
- int data_transfer_instructions, /* Count of dynamic instructions */
- i; /* Counter */
- u32 *cmd_datain, /* Address of datain/dataout code */
- *cmd_dataout; /* Incremented as we assemble */
-#ifdef notyet
- unsigned char *msgptr; /* Current byte in select message */
- int msglen; /* Length of whole select message */
-#endif
- unsigned long flags;
- u32 exp_select_indirect; /* Used in sanity check */
- NCR53c7x0_local_setup(cmd->device->host);
-
- if (!(tmp = allocate_cmd (cmd)))
- return NULL;
-
- /*
- * Copy CDB and initialised result fields from Scsi_Cmnd to NCR53c7x0_cmd.
- * We do this because NCR53c7x0_cmd may have a special cache mode
- * selected to cope with lack of bus snooping, etc.
- */
-
- memcpy(tmp->cmnd, cmd->cmnd, 12);
- tmp->result = cmd->result;
-
- /*
- * Decide whether we need to generate commands for DATA IN,
- * DATA OUT, neither, or both based on the SCSI command
- */
-
- switch (cmd->cmnd[0]) {
- /* These commands do DATA IN */
- case INQUIRY:
- case MODE_SENSE:
- case READ_6:
- case READ_10:
- case READ_CAPACITY:
- case REQUEST_SENSE:
- case READ_BLOCK_LIMITS:
- case READ_TOC:
- datain = 2 * (cmd->use_sg ? cmd->use_sg : 1) + 3;
- dataout = 0;
- break;
- /* These commands do DATA OUT */
- case MODE_SELECT:
- case WRITE_6:
- case WRITE_10:
-#if 0
- printk("scsi%d : command is ", host->host_no);
- __scsi_print_command(cmd->cmnd);
-#endif
-#if 0
- printk ("scsi%d : %d scatter/gather segments\n", host->host_no,
- cmd->use_sg);
-#endif
- datain = 0;
- dataout = 2 * (cmd->use_sg ? cmd->use_sg : 1) + 3;
-#if 0
- hostdata->options |= OPTION_DEBUG_INTR;
-#endif
- break;
- /*
- * These commands do no data transfer, we should force an
- * interrupt if a data phase is attempted on them.
- */
- case TEST_UNIT_READY:
- case ALLOW_MEDIUM_REMOVAL:
- case START_STOP:
- datain = dataout = 0;
- break;
- /*
- * We don't know about these commands, so generate code to handle
- * both DATA IN and DATA OUT phases. More efficient to identify them
- * and add them to the above cases.
- */
- default:
- printk("scsi%d : datain+dataout for command ", host->host_no);
- __scsi_print_command(cmd->cmnd);
- datain = dataout = 2 * (cmd->use_sg ? cmd->use_sg : 1) + 3;
- }
-
- /*
- * New code : so that active pointers work correctly regardless
- * of where the saved data pointer is at, we want to immediately
- * enter the dynamic code after selection, and on a non-data
- * phase perform a CALL to the non-data phase handler, with
- * returns back to this address.
- *
- * If a phase mismatch is encountered in the middle of a
- * Block MOVE instruction, we want to _leave_ that instruction
- * unchanged as the current case is, modify a temporary buffer,
- * and point the active pointer (TEMP) at that.
- *
- * Furthermore, we want to implement a saved data pointer,
- * set by the SAVE_DATA_POINTERs message.
- *
- * So, the data transfer segments will change to
- * CALL data_transfer, WHEN NOT data phase
- * MOVE x, x, WHEN data phase
- * ( repeat )
- * JUMP other_transfer
- */
-
- data_transfer_instructions = datain + dataout;
-
- /*
- * When we perform a request sense, we overwrite various things,
- * including the data transfer code. Make sure we have enough
- * space to do that.
- */
-
- if (data_transfer_instructions < 2)
- data_transfer_instructions = 2;
-
-
- /*
- * The saved data pointer is set up so that a RESTORE POINTERS message
- * will start the data transfer over at the beginning.
- */
-
- tmp->saved_data_pointer = virt_to_bus (hostdata->script) +
- hostdata->E_data_transfer;
-
- /*
- * Initialize Linux specific fields.
- */
-
- tmp->cmd = cmd;
- tmp->next = NULL;
- tmp->flags = 0;
- tmp->dsa_next_addr = virt_to_bus(tmp->dsa) + hostdata->dsa_next -
- hostdata->dsa_start;
- tmp->dsa_addr = virt_to_bus(tmp->dsa) - hostdata->dsa_start;
-
- /*
- * Calculate addresses of dynamic code to fill in DSA
- */
-
- tmp->data_transfer_start = tmp->dsa + (hostdata->dsa_end -
- hostdata->dsa_start) / sizeof(u32);
- tmp->data_transfer_end = tmp->data_transfer_start +
- 2 * data_transfer_instructions;
-
- cmd_datain = datain ? tmp->data_transfer_start : NULL;
- cmd_dataout = dataout ? (datain ? cmd_datain + 2 * datain : tmp->
- data_transfer_start) : NULL;
-
- /*
- * Fill in the NCR53c7x0_cmd structure as follows
- * dsa, with fixed up DSA code
- * datain code
- * dataout code
- */
-
- /* Copy template code into dsa and perform all necessary fixups */
- if (hostdata->dsa_fixup)
- hostdata->dsa_fixup(tmp);
-
- patch_dsa_32(tmp->dsa, dsa_next, 0, 0);
- /*
- * XXX is this giving 53c710 access to the Scsi_Cmnd in some way?
- * Do we need to change it for caching reasons?
- */
- patch_dsa_32(tmp->dsa, dsa_cmnd, 0, virt_to_bus(cmd));
-
- if (hostdata->options & OPTION_DEBUG_SYNCHRONOUS) {
-
- exp_select_indirect = ((1 << cmd->device->id) << 16) |
- (hostdata->sync[cmd->device->id].sxfer_sanity << 8);
-
- if (hostdata->sync[cmd->device->id].select_indirect !=
- exp_select_indirect) {
- printk ("scsi%d : sanity check failed select_indirect=0x%x\n",
- host->host_no, hostdata->sync[cmd->device->id].select_indirect);
- FATAL(host);
-
- }
- }
-
- patch_dsa_32(tmp->dsa, dsa_select, 0,
- hostdata->sync[cmd->device->id].select_indirect);
-
- /*
- * Right now, we'll do the WIDE and SYNCHRONOUS negotiations on
- * different commands; although it should be trivial to do them
- * both at the same time.
- */
- if (hostdata->initiate_wdtr & (1 << cmd->device->id)) {
- memcpy ((void *) (tmp->select + 1), (void *) wdtr_message,
- sizeof(wdtr_message));
- patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1 + sizeof(wdtr_message));
- local_irq_save(flags);
- hostdata->initiate_wdtr &= ~(1 << cmd->device->id);
- local_irq_restore(flags);
- } else if (hostdata->initiate_sdtr & (1 << cmd->device->id)) {
- memcpy ((void *) (tmp->select + 1), (void *) sdtr_message,
- sizeof(sdtr_message));
- patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1 + sizeof(sdtr_message));
- tmp->flags |= CMD_FLAG_SDTR;
- local_irq_save(flags);
- hostdata->initiate_sdtr &= ~(1 << cmd->device->id);
- local_irq_restore(flags);
-
- }
-#if 1
- else if (!(hostdata->talked_to & (1 << cmd->device->id)) &&
- !(hostdata->options & OPTION_NO_ASYNC)) {
-
- memcpy ((void *) (tmp->select + 1), (void *) async_message,
- sizeof(async_message));
- patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1 + sizeof(async_message));
- tmp->flags |= CMD_FLAG_SDTR;
- }
-#endif
- else
- patch_dsa_32(tmp->dsa, dsa_msgout, 0, 1);
-
- hostdata->talked_to |= (1 << cmd->device->id);
- tmp->select[0] = (hostdata->options & OPTION_DISCONNECT) ?
- IDENTIFY (1, cmd->device->lun) : IDENTIFY (0, cmd->device->lun);
- patch_dsa_32(tmp->dsa, dsa_msgout, 1, virt_to_bus(tmp->select));
- patch_dsa_32(tmp->dsa, dsa_cmdout, 0, cmd->cmd_len);
- patch_dsa_32(tmp->dsa, dsa_cmdout, 1, virt_to_bus(tmp->cmnd));
- patch_dsa_32(tmp->dsa, dsa_dataout, 0, cmd_dataout ?
- virt_to_bus (cmd_dataout)
- : virt_to_bus (hostdata->script) + hostdata->E_other_transfer);
- patch_dsa_32(tmp->dsa, dsa_datain, 0, cmd_datain ?
- virt_to_bus (cmd_datain)
- : virt_to_bus (hostdata->script) + hostdata->E_other_transfer);
- /*
- * XXX - need to make endian aware, should use separate variables
- * for both status and message bytes.
- */
- patch_dsa_32(tmp->dsa, dsa_msgin, 0, 1);
-/*
- * FIXME : these only works for little endian. We probably want to
- * provide message and status fields in the NCR53c7x0_cmd
- * structure, and assign them to cmd->result when we're done.
- */
-#ifdef BIG_ENDIAN
- patch_dsa_32(tmp->dsa, dsa_msgin, 1, virt_to_bus(&tmp->result) + 2);
- patch_dsa_32(tmp->dsa, dsa_status, 0, 1);
- patch_dsa_32(tmp->dsa, dsa_status, 1, virt_to_bus(&tmp->result) + 3);
-#else
- patch_dsa_32(tmp->dsa, dsa_msgin, 1, virt_to_bus(&tmp->result) + 1);
- patch_dsa_32(tmp->dsa, dsa_status, 0, 1);
- patch_dsa_32(tmp->dsa, dsa_status, 1, virt_to_bus(&tmp->result));
-#endif
- patch_dsa_32(tmp->dsa, dsa_msgout_other, 0, 1);
- patch_dsa_32(tmp->dsa, dsa_msgout_other, 1,
- virt_to_bus(&(hostdata->NCR53c7xx_msg_nop)));
-
- /*
- * Generate code for zero or more of the DATA IN, DATA OUT phases
- * in the format
- *
- * CALL data_transfer, WHEN NOT phase
- * MOVE first buffer length, first buffer address, WHEN phase
- * ...
- * MOVE last buffer length, last buffer address, WHEN phase
- * JUMP other_transfer
- */
-
-/*
- * See if we're getting to data transfer by generating an unconditional
- * interrupt.
- */
-#if 0
- if (datain) {
- cmd_datain[0] = 0x98080000;
- cmd_datain[1] = 0x03ffd00d;
- cmd_datain += 2;
- }
-#endif
-
-/*
- * XXX - I'm undecided whether all of this nonsense is faster
- * in the long run, or whether I should just go and implement a loop
- * on the NCR chip using table indirect mode?
- *
- * In any case, this is how it _must_ be done for 53c700/700-66 chips,
- * so this stays even when we come up with something better.
- *
- * When we're limited to 1 simultaneous command, no overlapping processing,
- * we're seeing 630K/sec, with 7% CPU usage on a slow Syquest 45M
- * drive.
- *
- * Not bad, not good. We'll see.
- */
-
- tmp->bounce.len = 0; /* Assume aligned buffer */
-
- for (i = 0; cmd->use_sg ? (i < cmd->use_sg) : !i; cmd_datain += 4,
- cmd_dataout += 4, ++i) {
- u32 vbuf = cmd->use_sg
- ? (u32)page_address(((struct scatterlist *)cmd->request_buffer)[i].page)+
- ((struct scatterlist *)cmd->request_buffer)[i].offset
- : (u32)(cmd->request_buffer);
- u32 bbuf = virt_to_bus((void *)vbuf);
- u32 count = cmd->use_sg ?
- ((struct scatterlist *)cmd->request_buffer)[i].length :
- cmd->request_bufflen;
-
- /*
- * If we have buffers which are not aligned with 16 byte cache
- * lines, then we just hope nothing accesses the other parts of
- * those cache lines while the transfer is in progress. That would
- * fill the cache, and subsequent reads of the dma data would pick
- * up the wrong thing.
- * XXX We need a bounce buffer to handle that correctly.
- */
-
- if (((bbuf & 15) || (count & 15)) && (datain || dataout))
- {
- /* Bounce buffer needed */
- if (cmd->use_sg)
- printk ("53c7xx: Non-aligned buffer with use_sg\n");
- else if (datain && dataout)
- printk ("53c7xx: Non-aligned buffer with datain && dataout\n");
- else if (count > 256)
- printk ("53c7xx: Non-aligned transfer > 256 bytes\n");
- else
- {
- if (datain)
- {
- tmp->bounce.len = count;
- tmp->bounce.addr = vbuf;
- bbuf = virt_to_bus(tmp->bounce.buf);
- tmp->bounce.buf[0] = 0xff;
- tmp->bounce.buf[1] = 0xfe;
- tmp->bounce.buf[2] = 0xfd;
- tmp->bounce.buf[3] = 0xfc;
- }
- if (dataout)
- {
- memcpy ((void *)tmp->bounce.buf, (void *)vbuf, count);
- bbuf = virt_to_bus(tmp->bounce.buf);
- }
- }
- }
-
- if (datain) {
- cache_clear(virt_to_phys((void *)vbuf), count);
- /* CALL other_in, WHEN NOT DATA_IN */
- cmd_datain[0] = ((DCMD_TYPE_TCI | DCMD_TCI_OP_CALL |
- DCMD_TCI_IO) << 24) |
- DBC_TCI_WAIT_FOR_VALID | DBC_TCI_COMPARE_PHASE;
- cmd_datain[1] = virt_to_bus (hostdata->script) +
- hostdata->E_other_in;
- /* MOVE count, buf, WHEN DATA_IN */
- cmd_datain[2] = ((DCMD_TYPE_BMI | DCMD_BMI_OP_MOVE_I | DCMD_BMI_IO)
- << 24) | count;
- cmd_datain[3] = bbuf;
-#if 0
- print_insn (host, cmd_datain, "dynamic ", 1);
- print_insn (host, cmd_datain + 2, "dynamic ", 1);
-#endif
- }
- if (dataout) {
- cache_push(virt_to_phys((void *)vbuf), count);
- /* CALL other_out, WHEN NOT DATA_OUT */
- cmd_dataout[0] = ((DCMD_TYPE_TCI | DCMD_TCI_OP_CALL) << 24) |
- DBC_TCI_WAIT_FOR_VALID | DBC_TCI_COMPARE_PHASE;
- cmd_dataout[1] = virt_to_bus(hostdata->script) +
- hostdata->E_other_out;
- /* MOVE count, buf, WHEN DATA+OUT */
- cmd_dataout[2] = ((DCMD_TYPE_BMI | DCMD_BMI_OP_MOVE_I) << 24)
- | count;
- cmd_dataout[3] = bbuf;
-#if 0
- print_insn (host, cmd_dataout, "dynamic ", 1);
- print_insn (host, cmd_dataout + 2, "dynamic ", 1);
-#endif
- }
- }
-
- /*
- * Install JUMP instructions after the data transfer routines to return
- * control to the do_other_transfer routines.
- */
-
-
- if (datain) {
- cmd_datain[0] = ((DCMD_TYPE_TCI | DCMD_TCI_OP_JUMP) << 24) |
- DBC_TCI_TRUE;
- cmd_datain[1] = virt_to_bus(hostdata->script) +
- hostdata->E_other_transfer;
-#if 0
- print_insn (host, cmd_datain, "dynamic jump ", 1);
-#endif
- cmd_datain += 2;
- }
-#if 0
- if (datain) {
- cmd_datain[0] = 0x98080000;
- cmd_datain[1] = 0x03ffdeed;
- cmd_datain += 2;
- }
-#endif
- if (dataout) {
- cmd_dataout[0] = ((DCMD_TYPE_TCI | DCMD_TCI_OP_JUMP) << 24) |
- DBC_TCI_TRUE;
- cmd_dataout[1] = virt_to_bus(hostdata->script) +
- hostdata->E_other_transfer;
-#if 0
- print_insn (host, cmd_dataout, "dynamic jump ", 1);
-#endif
- cmd_dataout += 2;
- }
-
- return tmp;
-}
-
-/*
- * Function : int NCR53c7xx_queue_command (Scsi_Cmnd *cmd,
- * void (*done)(Scsi_Cmnd *))
- *
- * Purpose : enqueues a SCSI command
- *
- * Inputs : cmd - SCSI command, done - function called on completion, with
- * a pointer to the command descriptor.
- *
- * Returns : 0
- *
- * Side effects :
- * cmd is added to the per instance driver issue_queue, with major
- * twiddling done to the host specific fields of cmd. If the
- * process_issue_queue coroutine isn't running, it is restarted.
- *
- * NOTE : we use the host_scribble field of the Scsi_Cmnd structure to
- * hold our own data, and pervert the ptr field of the SCp field
- * to create a linked list.
- */
-
-int
-NCR53c7xx_queue_command (Scsi_Cmnd *cmd, void (* done)(Scsi_Cmnd *)) {
- struct Scsi_Host *host = cmd->device->host;
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) host->hostdata[0];
- unsigned long flags;
- Scsi_Cmnd *tmp;
-
- cmd->scsi_done = done;
- cmd->host_scribble = NULL;
- cmd->SCp.ptr = NULL;
- cmd->SCp.buffer = NULL;
-
-#ifdef VALID_IDS
- /* Ignore commands on invalid IDs */
- if (!hostdata->valid_ids[cmd->device->id]) {
- printk("scsi%d : ignoring target %d lun %d\n", host->host_no,
- cmd->device->id, cmd->device->lun);
- cmd->result = (DID_BAD_TARGET << 16);
- done(cmd);
- return 0;
- }
-#endif
-
- local_irq_save(flags);
- if ((hostdata->options & (OPTION_DEBUG_INIT_ONLY|OPTION_DEBUG_PROBE_ONLY))
- || ((hostdata->options & OPTION_DEBUG_TARGET_LIMIT) &&
- !(hostdata->debug_lun_limit[cmd->device->id] & (1 << cmd->device->lun)))
-#ifdef LINUX_1_2
- || cmd->device->id > 7
-#else
- || cmd->device->id >= host->max_id
-#endif
- || cmd->device->id == host->this_id
- || hostdata->state == STATE_DISABLED) {
- printk("scsi%d : disabled or bad target %d lun %d\n", host->host_no,
- cmd->device->id, cmd->device->lun);
- cmd->result = (DID_BAD_TARGET << 16);
- done(cmd);
- local_irq_restore(flags);
- return 0;
- }
-
- if ((hostdata->options & OPTION_DEBUG_NCOMMANDS_LIMIT) &&
- (hostdata->debug_count_limit == 0)) {
- printk("scsi%d : maximum commands exceeded\n", host->host_no);
- cmd->result = (DID_BAD_TARGET << 16);
- done(cmd);
- local_irq_restore(flags);
- return 0;
- }
-
- if (hostdata->options & OPTION_DEBUG_READ_ONLY) {
- switch (cmd->cmnd[0]) {
- case WRITE_6:
- case WRITE_10:
- printk("scsi%d : WRITE attempted with NO_WRITE debugging flag set\n",
- host->host_no);
- cmd->result = (DID_BAD_TARGET << 16);
- done(cmd);
- local_irq_restore(flags);
- return 0;
- }
- }
-
- if ((hostdata->options & OPTION_DEBUG_TARGET_LIMIT) &&
- hostdata->debug_count_limit != -1)
- --hostdata->debug_count_limit;
-
- cmd->result = 0xffff; /* The NCR will overwrite message
- and status with valid data */
- cmd->host_scribble = (unsigned char *) tmp = create_cmd (cmd);
-
- /*
- * REQUEST SENSE commands are inserted at the head of the queue
- * so that we do not clear the contingent allegiance condition
- * they may be looking at.
- */
-
- if (!(hostdata->issue_queue) || (cmd->cmnd[0] == REQUEST_SENSE)) {
- cmd->SCp.ptr = (unsigned char *) hostdata->issue_queue;
- hostdata->issue_queue = cmd;
- } else {
- for (tmp = (Scsi_Cmnd *) hostdata->issue_queue; tmp->SCp.ptr;
- tmp = (Scsi_Cmnd *) tmp->SCp.ptr);
- tmp->SCp.ptr = (unsigned char *) cmd;
- }
- local_irq_restore(flags);
- run_process_issue_queue();
- return 0;
-}
-
-/*
- * Function : void to_schedule_list (struct Scsi_Host *host,
- * struct NCR53c7x0_hostdata * hostdata, Scsi_Cmnd *cmd)
- *
- * Purpose : takes a SCSI command which was just removed from the
- * issue queue, and deals with it by inserting it in the first
- * free slot in the schedule list or by terminating it immediately.
- *
- * Inputs :
- * host - SCSI host adapter; hostdata - hostdata structure for
- * this adapter; cmd - a pointer to the command; should have
- * the host_scribble field initialized to point to a valid
- *
- * Side effects :
- * cmd is added to the per instance schedule list, with minor
- * twiddling done to the host specific fields of cmd.
- *
- */
-
-static __inline__ void
-to_schedule_list (struct Scsi_Host *host, struct NCR53c7x0_hostdata *hostdata,
- struct NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- Scsi_Cmnd *tmp = cmd->cmd;
- unsigned long flags;
- /* dsa start is negative, so subtraction is used */
- volatile u32 *ncrcurrent;
-
- int i;
- NCR53c7x0_local_setup(host);
-#if 0
- printk("scsi%d : new dsa is 0x%lx (virt 0x%p)\n", host->host_no,
- virt_to_bus(hostdata->dsa), hostdata->dsa);
-#endif
-
- local_irq_save(flags);
-
- /*
- * Work around race condition : if an interrupt fired and we
- * got disabled forget about this command.
- */
-
- if (hostdata->state == STATE_DISABLED) {
- printk("scsi%d : driver disabled\n", host->host_no);
- tmp->result = (DID_BAD_TARGET << 16);
- cmd->next = (struct NCR53c7x0_cmd *) hostdata->free;
- hostdata->free = cmd;
- tmp->scsi_done(tmp);
- local_irq_restore(flags);
- return;
- }
-
- for (i = host->can_queue, ncrcurrent = hostdata->schedule;
- i > 0 && ncrcurrent[0] != hostdata->NOP_insn;
- --i, ncrcurrent += 2 /* JUMP instructions are two words */);
-
- if (i > 0) {
- ++hostdata->busy[tmp->device->id][tmp->device->lun];
- cmd->next = hostdata->running_list;
- hostdata->running_list = cmd;
-
- /* Restore this instruction to a NOP once the command starts */
- cmd->dsa [(hostdata->dsa_jump_dest - hostdata->dsa_start) /
- sizeof(u32)] = (u32) virt_to_bus ((void *)ncrcurrent);
- /* Replace the current jump operand. */
- ncrcurrent[1] =
- virt_to_bus ((void *) cmd->dsa) + hostdata->E_dsa_code_begin -
- hostdata->E_dsa_code_template;
- /* Replace the NOP instruction with a JUMP */
- ncrcurrent[0] = ((DCMD_TYPE_TCI|DCMD_TCI_OP_JUMP) << 24) |
- DBC_TCI_TRUE;
- } else {
- printk ("scsi%d: no free slot\n", host->host_no);
- disable(host);
- tmp->result = (DID_ERROR << 16);
- cmd->next = (struct NCR53c7x0_cmd *) hostdata->free;
- hostdata->free = cmd;
- tmp->scsi_done(tmp);
- local_irq_restore(flags);
- return;
- }
-
- /*
- * If the NCR chip is in an idle state, start it running the scheduler
- * immediately. Otherwise, signal the chip to jump to schedule as
- * soon as it is idle.
- */
-
- if (hostdata->idle) {
- hostdata->idle = 0;
- hostdata->state = STATE_RUNNING;
- NCR53c7x0_write32 (DSP_REG, virt_to_bus ((void *)hostdata->schedule));
- if (hostdata->options & OPTION_DEBUG_TRACE)
- NCR53c7x0_write8 (DCNTL_REG, hostdata->saved_dcntl |
- DCNTL_SSM | DCNTL_STD);
- } else {
- NCR53c7x0_write8(hostdata->istat, ISTAT_10_SIGP);
- }
-
- local_irq_restore(flags);
-}
-
-/*
- * Function : busyp (struct Scsi_Host *host, struct NCR53c7x0_hostdata
- * *hostdata, Scsi_Cmnd *cmd)
- *
- * Purpose : decide if we can pass the given SCSI command on to the
- * device in question or not.
- *
- * Returns : non-zero when we're busy, 0 when we aren't.
- */
-
-static __inline__ int
-busyp (struct Scsi_Host *host, struct NCR53c7x0_hostdata *hostdata,
- Scsi_Cmnd *cmd) {
- /* FIXME : in the future, this needs to accommodate SCSI-II tagged
- queuing, and we may be able to play with fairness here a bit.
- */
- return hostdata->busy[cmd->device->id][cmd->device->lun];
-}
-
-/*
- * Function : process_issue_queue (void)
- *
- * Purpose : transfer commands from the issue queue to NCR start queue
- * of each NCR53c7/8xx in the system, avoiding kernel stack
- * overflows when the scsi_done() function is invoked recursively.
- *
- * NOTE : process_issue_queue exits with interrupts *disabled*, so the
- * caller must reenable them if it desires.
- *
- * NOTE : process_issue_queue should be called from both
- * NCR53c7x0_queue_command() and from the interrupt handler
- * after command completion in case NCR53c7x0_queue_command()
- * isn't invoked again but we've freed up resources that are
- * needed.
- */
-
-static void
-process_issue_queue (unsigned long flags) {
- Scsi_Cmnd *tmp, *prev;
- struct Scsi_Host *host;
- struct NCR53c7x0_hostdata *hostdata;
- int done;
-
- /*
- * We run (with interrupts disabled) until we're sure that none of
- * the host adapters have anything that can be done, at which point
- * we set process_issue_queue_running to 0 and exit.
- *
- * Interrupts are enabled before doing various other internal
- * instructions, after we've decided that we need to run through
- * the loop again.
- *
- */
-
- do {
- local_irq_disable(); /* Freeze request queues */
- done = 1;
- for (host = first_host; host && host->hostt == the_template;
- host = host->next) {
- hostdata = (struct NCR53c7x0_hostdata *) host->hostdata[0];
- local_irq_disable();
- if (hostdata->issue_queue) {
- if (hostdata->state == STATE_DISABLED) {
- tmp = (Scsi_Cmnd *) hostdata->issue_queue;
- hostdata->issue_queue = (Scsi_Cmnd *) tmp->SCp.ptr;
- tmp->result = (DID_BAD_TARGET << 16);
- if (tmp->host_scribble) {
- ((struct NCR53c7x0_cmd *)tmp->host_scribble)->next =
- hostdata->free;
- hostdata->free =
- (struct NCR53c7x0_cmd *)tmp->host_scribble;
- tmp->host_scribble = NULL;
- }
- tmp->scsi_done (tmp);
- done = 0;
- } else
- for (tmp = (Scsi_Cmnd *) hostdata->issue_queue,
- prev = NULL; tmp; prev = tmp, tmp = (Scsi_Cmnd *)
- tmp->SCp.ptr)
- if (!tmp->host_scribble ||
- !busyp (host, hostdata, tmp)) {
- if (prev)
- prev->SCp.ptr = tmp->SCp.ptr;
- else
- hostdata->issue_queue = (Scsi_Cmnd *)
- tmp->SCp.ptr;
- tmp->SCp.ptr = NULL;
- if (tmp->host_scribble) {
- if (hostdata->options & OPTION_DEBUG_QUEUES)
- printk ("scsi%d : moving command for target %d lun %d to start list\n",
- host->host_no, tmp->device->id, tmp->device->lun);
-
-
- to_schedule_list (host, hostdata,
- (struct NCR53c7x0_cmd *)
- tmp->host_scribble);
- } else {
- if (((tmp->result & 0xff) == 0xff) ||
- ((tmp->result & 0xff00) == 0xff00)) {
- printk ("scsi%d : danger Will Robinson!\n",
- host->host_no);
- tmp->result = DID_ERROR << 16;
- disable (host);
- }
- tmp->scsi_done(tmp);
- }
- done = 0;
- } /* if target/lun is not busy */
- } /* if hostdata->issue_queue */
- if (!done)
- local_irq_restore(flags);
- } /* for host */
- } while (!done);
- process_issue_queue_running = 0;
-}
-
-/*
- * Function : static void intr_scsi (struct Scsi_Host *host,
- * struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : handle all SCSI interrupts, indicated by the setting
- * of the SIP bit in the ISTAT register.
- *
- * Inputs : host, cmd - host and NCR command causing the interrupt, cmd
- * may be NULL.
- */
-
-static void
-intr_scsi (struct Scsi_Host *host, struct NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) host->hostdata[0];
- unsigned char sstat0_sist0, sist1, /* Registers */
- fatal; /* Did a fatal interrupt
- occur ? */
-
- NCR53c7x0_local_setup(host);
-
- fatal = 0;
-
- sstat0_sist0 = NCR53c7x0_read8(SSTAT0_REG);
- sist1 = 0;
-
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : SIST0 0x%0x, SIST1 0x%0x\n", host->host_no,
- sstat0_sist0, sist1);
-
- /* 250ms selection timeout */
- if (sstat0_sist0 & SSTAT0_700_STO) {
- fatal = 1;
- if (hostdata->options & OPTION_DEBUG_INTR) {
- printk ("scsi%d : Selection Timeout\n", host->host_no);
- if (cmd) {
- printk("scsi%d : target %d, lun %d, command ",
- host->host_no, cmd->cmd->device->id, cmd->cmd->device->lun);
- __scsi_print_command (cmd->cmd->cmnd);
- printk("scsi%d : dsp = 0x%x (virt 0x%p)\n", host->host_no,
- NCR53c7x0_read32(DSP_REG),
- bus_to_virt(NCR53c7x0_read32(DSP_REG)));
- } else {
- printk("scsi%d : no command\n", host->host_no);
- }
- }
-/*
- * XXX - question : how do we want to handle the Illegal Instruction
- * interrupt, which may occur before or after the Selection Timeout
- * interrupt?
- */
-
- if (1) {
- hostdata->idle = 1;
- hostdata->expecting_sto = 0;
-
- if (hostdata->test_running) {
- hostdata->test_running = 0;
- hostdata->test_completed = 3;
- } else if (cmd) {
- abnormal_finished(cmd, DID_BAD_TARGET << 16);
- }
-#if 0
- hostdata->intrs = 0;
-#endif
- }
- }
-
-/*
- * FIXME : in theory, we can also get a UDC when a STO occurs.
- */
- if (sstat0_sist0 & SSTAT0_UDC) {
- fatal = 1;
- if (cmd) {
- printk("scsi%d : target %d lun %d unexpected disconnect\n",
- host->host_no, cmd->cmd->device->id, cmd->cmd->device->lun);
- print_lots (host);
- abnormal_finished(cmd, DID_ERROR << 16);
- } else
- printk("scsi%d : unexpected disconnect (no command)\n",
- host->host_no);
-
- hostdata->dsp = (u32 *) hostdata->schedule;
- hostdata->dsp_changed = 1;
- }
-
- /* SCSI PARITY error */
- if (sstat0_sist0 & SSTAT0_PAR) {
- fatal = 1;
- if (cmd && cmd->cmd) {
- printk("scsi%d : target %d lun %d parity error.\n",
- host->host_no, cmd->cmd->device->id, cmd->cmd->device->lun);
- abnormal_finished (cmd, DID_PARITY << 16);
- } else
- printk("scsi%d : parity error\n", host->host_no);
- /* Should send message out, parity error */
-
- /* XXX - Reduce synchronous transfer rate! */
- hostdata->dsp = hostdata->script + hostdata->E_initiator_abort /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- /* SCSI GROSS error */
- }
-
- if (sstat0_sist0 & SSTAT0_SGE) {
- fatal = 1;
- printk("scsi%d : gross error, saved2_dsa = 0x%x\n", host->host_no,
- (unsigned int)hostdata->saved2_dsa);
- print_lots (host);
-
- /*
- * A SCSI gross error may occur when we have
- *
- * - A synchronous offset which causes the SCSI FIFO to be overwritten.
- *
- * - A REQ which causes the maximum synchronous offset programmed in
- * the SXFER register to be exceeded.
- *
- * - A phase change with an outstanding synchronous offset.
- *
- * - Residual data in the synchronous data FIFO, with a transfer
- * other than a synchronous receive is started.$#
- */
-
-
- /* XXX Should deduce synchronous transfer rate! */
- hostdata->dsp = hostdata->script + hostdata->E_initiator_abort /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- /* Phase mismatch */
- }
-
- if (sstat0_sist0 & SSTAT0_MA) {
- fatal = 1;
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : SSTAT0_MA\n", host->host_no);
- intr_phase_mismatch (host, cmd);
- }
-
-#if 0
- if (sstat0_sist0 & SIST0_800_RSL)
- printk ("scsi%d : Oh no Mr. Bill!\n", host->host_no);
-#endif
-
-/*
- * If a fatal SCSI interrupt occurs, we must insure that the DMA and
- * SCSI FIFOs were flushed.
- */
-
- if (fatal) {
- if (!hostdata->dstat_valid) {
- hostdata->dstat = NCR53c7x0_read8(DSTAT_REG);
- hostdata->dstat_valid = 1;
- }
-
- if (!(hostdata->dstat & DSTAT_DFE)) {
- printk ("scsi%d : DMA FIFO not empty\n", host->host_no);
- /*
- * Really need to check this code for 710 RGH.
- * Havn't seen any problems, but maybe we should FLUSH before
- * clearing sometimes.
- */
- NCR53c7x0_write8 (CTEST8_REG, CTEST8_10_CLF);
- while (NCR53c7x0_read8 (CTEST8_REG) & CTEST8_10_CLF)
- ;
- hostdata->dstat |= DSTAT_DFE;
- }
- }
-}
-
-#ifdef CYCLIC_TRACE
-
-/*
- * The following implements a cyclic log of instructions executed, if you turn
- * TRACE on. It will also print the log for you. Very useful when debugging
- * 53c710 support, possibly not really needed any more.
- */
-
-u32 insn_log[4096];
-u32 insn_log_index = 0;
-
-void log1 (u32 i)
-{
- insn_log[insn_log_index++] = i;
- if (insn_log_index == 4096)
- insn_log_index = 0;
-}
-
-void log_insn (u32 *ip)
-{
- log1 ((u32)ip);
- log1 (*ip);
- log1 (*(ip+1));
- if (((*ip >> 24) & DCMD_TYPE_MASK) == DCMD_TYPE_MMI)
- log1 (*(ip+2));
-}
-
-void dump_log(void)
-{
- int cnt = 0;
- int i = insn_log_index;
- int size;
- struct Scsi_Host *host = first_host;
-
- while (cnt < 4096) {
- printk ("%08x (+%6x): ", insn_log[i], (insn_log[i] - (u32)&(((struct NCR53c7x0_hostdata *)host->hostdata[0])->script))/4);
- if (++i == 4096)
- i = 0;
- cnt++;
- if (((insn_log[i] >> 24) & DCMD_TYPE_MASK) == DCMD_TYPE_MMI)
- size = 3;
- else
- size = 2;
- while (size--) {
- printk ("%08x ", insn_log[i]);
- if (++i == 4096)
- i = 0;
- cnt++;
- }
- printk ("\n");
- }
-}
-#endif
-
-
-/*
- * Function : static void NCR53c7x0_intfly (struct Scsi_Host *host)
- *
- * Purpose : Scan command queue for specified host, looking for completed
- * commands.
- *
- * Inputs : Scsi_Host pointer.
- *
- * This is called from the interrupt handler, when a simulated INTFLY
- * interrupt occurs.
- */
-
-static void
-NCR53c7x0_intfly (struct Scsi_Host *host)
-{
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata; /* host->hostdata[0] */
- struct NCR53c7x0_cmd *cmd, /* command which halted */
- **cmd_prev_ptr;
- unsigned long flags;
- char search_found = 0; /* Got at least one ? */
-
- hostdata = (struct NCR53c7x0_hostdata *) host->hostdata[0];
- NCR53c7x0_local_setup(host);
-
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : INTFLY\n", host->host_no);
-
- /*
- * Traverse our list of running commands, and look
- * for those with valid (non-0xff ff) status and message
- * bytes encoded in the result which signify command
- * completion.
- */
-
- local_irq_save(flags);
-restart:
- for (cmd_prev_ptr = (struct NCR53c7x0_cmd **)&(hostdata->running_list),
- cmd = (struct NCR53c7x0_cmd *) hostdata->running_list; cmd ;
- cmd_prev_ptr = (struct NCR53c7x0_cmd **) &(cmd->next),
- cmd = (struct NCR53c7x0_cmd *) cmd->next)
- {
- Scsi_Cmnd *tmp;
-
- if (!cmd) {
- printk("scsi%d : very weird.\n", host->host_no);
- break;
- }
-
- if (!(tmp = cmd->cmd)) {
- printk("scsi%d : weird. NCR53c7x0_cmd has no Scsi_Cmnd\n",
- host->host_no);
- continue;
- }
- /* Copy the result over now; may not be complete,
- * but subsequent tests may as well be done on
- * cached memory.
- */
- tmp->result = cmd->result;
-
- if (((tmp->result & 0xff) == 0xff) ||
- ((tmp->result & 0xff00) == 0xff00))
- continue;
-
- search_found = 1;
-
- if (cmd->bounce.len)
- memcpy ((void *)cmd->bounce.addr,
- (void *)cmd->bounce.buf, cmd->bounce.len);
-
- /* Important - remove from list _before_ done is called */
- if (cmd_prev_ptr)
- *cmd_prev_ptr = (struct NCR53c7x0_cmd *) cmd->next;
-
- --hostdata->busy[tmp->device->id][tmp->device->lun];
- cmd->next = hostdata->free;
- hostdata->free = cmd;
-
- tmp->host_scribble = NULL;
-
- if (hostdata->options & OPTION_DEBUG_INTR) {
- printk ("scsi%d : command complete : pid %lu, id %d,lun %d result 0x%x ",
- host->host_no, tmp->pid, tmp->device->id, tmp->device->lun, tmp->result);
- __scsi_print_command (tmp->cmnd);
- }
-
- tmp->scsi_done(tmp);
- goto restart;
- }
- local_irq_restore(flags);
-
- if (!search_found) {
- printk ("scsi%d : WARNING : INTFLY with no completed commands.\n",
- host->host_no);
- } else {
- run_process_issue_queue();
- }
- return;
-}
-
-/*
- * Function : static irqreturn_t NCR53c7x0_intr (int irq, void *dev_id)
- *
- * Purpose : handle NCR53c7x0 interrupts for all NCR devices sharing
- * the same IRQ line.
- *
- * Inputs : Since we're using the IRQF_DISABLED interrupt handler
- * semantics, irq indicates the interrupt which invoked
- * this handler.
- *
- * On the 710 we simualte an INTFLY with a script interrupt, and the
- * script interrupt handler will call back to this function.
- */
-
-static irqreturn_t
-NCR53c7x0_intr (int irq, void *dev_id)
-{
- NCR53c7x0_local_declare();
- struct Scsi_Host *host; /* Host we are looking at */
- unsigned char istat; /* Values of interrupt regs */
- struct NCR53c7x0_hostdata *hostdata; /* host->hostdata[0] */
- struct NCR53c7x0_cmd *cmd; /* command which halted */
- u32 *dsa; /* DSA */
- int handled = 0;
-
-#ifdef NCR_DEBUG
- char buf[80]; /* Debugging sprintf buffer */
- size_t buflen; /* Length of same */
-#endif
-
- host = (struct Scsi_Host *)dev_id;
- hostdata = (struct NCR53c7x0_hostdata *) host->hostdata[0];
- NCR53c7x0_local_setup(host);
-
- /*
- * Only read istat once per loop, since reading it again will unstack
- * interrupts
- */
-
- while ((istat = NCR53c7x0_read8(hostdata->istat)) & (ISTAT_SIP|ISTAT_DIP)) {
- handled = 1;
- hostdata->dsp_changed = 0;
- hostdata->dstat_valid = 0;
- hostdata->state = STATE_HALTED;
-
- if (NCR53c7x0_read8 (SSTAT2_REG) & SSTAT2_FF_MASK)
- printk ("scsi%d : SCSI FIFO not empty\n", host->host_no);
-
- /*
- * NCR53c700 and NCR53c700-66 change the current SCSI
- * process, hostdata->ncrcurrent, in the Linux driver so
- * cmd = hostdata->ncrcurrent.
- *
- * With other chips, we must look through the commands
- * executing and find the command structure which
- * corresponds to the DSA register.
- */
-
- if (hostdata->options & OPTION_700) {
- cmd = (struct NCR53c7x0_cmd *) hostdata->ncrcurrent;
- } else {
- dsa = bus_to_virt(NCR53c7x0_read32(DSA_REG));
- for (cmd = (struct NCR53c7x0_cmd *) hostdata->running_list;
- cmd && (dsa + (hostdata->dsa_start / sizeof(u32))) != cmd->dsa;
- cmd = (struct NCR53c7x0_cmd *)(cmd->next))
- ;
- }
- if (hostdata->options & OPTION_DEBUG_INTR) {
- if (cmd) {
- printk("scsi%d : interrupt for pid %lu, id %d, lun %d ",
- host->host_no, cmd->cmd->pid, (int) cmd->cmd->device->id,
- (int) cmd->cmd->device->lun);
- __scsi_print_command (cmd->cmd->cmnd);
- } else {
- printk("scsi%d : no active command\n", host->host_no);
- }
- }
-
- if (istat & ISTAT_SIP) {
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : ISTAT_SIP\n", host->host_no);
- intr_scsi (host, cmd);
- }
-
- if (istat & ISTAT_DIP) {
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : ISTAT_DIP\n", host->host_no);
- intr_dma (host, cmd);
- }
-
- if (!hostdata->dstat_valid) {
- hostdata->dstat = NCR53c7x0_read8(DSTAT_REG);
- hostdata->dstat_valid = 1;
- }
-
- if (!(hostdata->dstat & DSTAT_DFE)) {
- printk ("scsi%d : DMA FIFO not empty\n", host->host_no);
- /* Really need to check this out for 710 RGH */
- NCR53c7x0_write8 (CTEST8_REG, CTEST8_10_CLF);
- while (NCR53c7x0_read8 (CTEST8_REG) & CTEST8_10_CLF)
- ;
- hostdata->dstat |= DSTAT_DFE;
- }
-
- if (!hostdata->idle && hostdata->state == STATE_HALTED) {
- if (!hostdata->dsp_changed)
- hostdata->dsp = (u32 *)bus_to_virt(NCR53c7x0_read32(DSP_REG));
-#if 0
- printk("scsi%d : new dsp is 0x%lx (virt 0x%p)\n",
- host->host_no, virt_to_bus(hostdata->dsp), hostdata->dsp);
-#endif
-
- hostdata->state = STATE_RUNNING;
- NCR53c7x0_write32 (DSP_REG, virt_to_bus(hostdata->dsp));
- if (hostdata->options & OPTION_DEBUG_TRACE) {
-#ifdef CYCLIC_TRACE
- log_insn (hostdata->dsp);
-#else
- print_insn (host, hostdata->dsp, "t ", 1);
-#endif
- NCR53c7x0_write8 (DCNTL_REG,
- hostdata->saved_dcntl | DCNTL_SSM | DCNTL_STD);
- }
- }
- }
- return IRQ_HANDLED;
-}
-
-
-/*
- * Function : static int abort_connected (struct Scsi_Host *host)
- *
- * Purpose : Assuming that the NCR SCSI processor is currently
- * halted, break the currently established nexus. Clean
- * up of the NCR53c7x0_cmd and Scsi_Cmnd structures should
- * be done on receipt of the abort interrupt.
- *
- * Inputs : host - SCSI host
- *
- */
-
-static int
-abort_connected (struct Scsi_Host *host) {
-#ifdef NEW_ABORT
- NCR53c7x0_local_declare();
-#endif
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
-/* FIXME : this probably should change for production kernels; at the
- least, counter should move to a per-host structure. */
- static int counter = 5;
-#ifdef NEW_ABORT
- int sstat, phase, offset;
- u32 *script;
- NCR53c7x0_local_setup(host);
-#endif
-
- if (--counter <= 0) {
- disable(host);
- return 0;
- }
-
- printk ("scsi%d : DANGER : abort_connected() called \n",
- host->host_no);
-
-#ifdef NEW_ABORT
-
-/*
- * New strategy : Rather than using a generic abort routine,
- * we'll specifically try to source or sink the appropriate
- * amount of data for the phase we're currently in (taking into
- * account the current synchronous offset)
- */
-
- sstat = NCR53c8x0_read8 (SSTAT2_REG);
- offset = OFFSET (sstat & SSTAT2_FF_MASK) >> SSTAT2_FF_SHIFT;
- phase = sstat & SSTAT2_PHASE_MASK;
-
-/*
- * SET ATN
- * MOVE source_or_sink, WHEN CURRENT PHASE
- * < repeat for each outstanding byte >
- * JUMP send_abort_message
- */
-
- script = hostdata->abort_script = kmalloc (
- 8 /* instruction size */ * (
- 1 /* set ATN */ +
- (!offset ? 1 : offset) /* One transfer per outstanding byte */ +
- 1 /* send abort message */),
- GFP_ATOMIC);
-
-
-#else /* def NEW_ABORT */
- hostdata->dsp = hostdata->script + hostdata->E_initiator_abort /
- sizeof(u32);
-#endif /* def NEW_ABORT */
- hostdata->dsp_changed = 1;
-
-/* XXX - need to flag the command as aborted after the abort_connected
- code runs
- */
- return 0;
-}
-
-/*
- * Function : static int datapath_residual (Scsi_Host *host)
- *
- * Purpose : return residual data count of what's in the chip.
- *
- * Inputs : host - SCSI host
- */
-
-static int
-datapath_residual (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- int count, synchronous, sstat;
- unsigned int ddir;
-
- NCR53c7x0_local_setup(host);
- /* COMPAT : the 700 and 700-66 need to use DFIFO_00_BO_MASK */
- count = ((NCR53c7x0_read8 (DFIFO_REG) & DFIFO_10_BO_MASK) -
- (NCR53c7x0_read32 (DBC_REG) & DFIFO_10_BO_MASK)) & DFIFO_10_BO_MASK;
- synchronous = NCR53c7x0_read8 (SXFER_REG) & SXFER_MO_MASK;
- /* COMPAT : DDIR is elsewhere on non-'8xx chips. */
- ddir = NCR53c7x0_read8 (CTEST0_REG_700) & CTEST0_700_DDIR;
-
- if (ddir) {
- /* Receive */
- if (synchronous)
- count += (NCR53c7x0_read8 (SSTAT2_REG) & SSTAT2_FF_MASK) >> SSTAT2_FF_SHIFT;
- else
- if (NCR53c7x0_read8 (SSTAT1_REG) & SSTAT1_ILF)
- ++count;
- } else {
- /* Send */
- sstat = NCR53c7x0_read8 (SSTAT1_REG);
- if (sstat & SSTAT1_OLF)
- ++count;
- if (synchronous && (sstat & SSTAT1_ORF))
- ++count;
- }
- return count;
-}
-
-/*
- * Function : static const char * sbcl_to_phase (int sbcl)_
- *
- * Purpose : Convert SBCL register to user-parsable phase representation
- *
- * Inputs : sbcl - value of sbcl register
- */
-
-
-static const char *
-sbcl_to_phase (int sbcl) {
- switch (sbcl & SBCL_PHASE_MASK) {
- case SBCL_PHASE_DATAIN:
- return "DATAIN";
- case SBCL_PHASE_DATAOUT:
- return "DATAOUT";
- case SBCL_PHASE_MSGIN:
- return "MSGIN";
- case SBCL_PHASE_MSGOUT:
- return "MSGOUT";
- case SBCL_PHASE_CMDOUT:
- return "CMDOUT";
- case SBCL_PHASE_STATIN:
- return "STATUSIN";
- default:
- return "unknown";
- }
-}
-
-/*
- * Function : static const char * sstat2_to_phase (int sstat)_
- *
- * Purpose : Convert SSTAT2 register to user-parsable phase representation
- *
- * Inputs : sstat - value of sstat register
- */
-
-
-static const char *
-sstat2_to_phase (int sstat) {
- switch (sstat & SSTAT2_PHASE_MASK) {
- case SSTAT2_PHASE_DATAIN:
- return "DATAIN";
- case SSTAT2_PHASE_DATAOUT:
- return "DATAOUT";
- case SSTAT2_PHASE_MSGIN:
- return "MSGIN";
- case SSTAT2_PHASE_MSGOUT:
- return "MSGOUT";
- case SSTAT2_PHASE_CMDOUT:
- return "CMDOUT";
- case SSTAT2_PHASE_STATIN:
- return "STATUSIN";
- default:
- return "unknown";
- }
-}
-
-/*
- * Function : static void intr_phase_mismatch (struct Scsi_Host *host,
- * struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : Handle phase mismatch interrupts
- *
- * Inputs : host, cmd - host and NCR command causing the interrupt, cmd
- * may be NULL.
- *
- * Side effects : The abort_connected() routine is called or the NCR chip
- * is restarted, jumping to the command_complete entry point, or
- * patching the address and transfer count of the current instruction
- * and calling the msg_in entry point as appropriate.
- */
-
-static void
-intr_phase_mismatch (struct Scsi_Host *host, struct NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- u32 dbc_dcmd, *dsp, *dsp_next;
- unsigned char dcmd, sbcl;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- int residual;
- enum {ACTION_ABORT, ACTION_ABORT_PRINT, ACTION_CONTINUE} action =
- ACTION_ABORT_PRINT;
- const char *where = NULL;
-
- NCR53c7x0_local_setup(host);
-
- /*
- * Corrective action is based on where in the SCSI SCRIPT(tm) the error
- * occurred, as well as which SCSI phase we are currently in.
- */
- dsp_next = bus_to_virt(NCR53c7x0_read32(DSP_REG));
-
- /*
- * Fetch the current instruction, and remove the operands for easier
- * interpretation.
- */
- dbc_dcmd = NCR53c7x0_read32(DBC_REG);
- dcmd = (dbc_dcmd & 0xff000000) >> 24;
- /*
- * Like other processors, the NCR adjusts the instruction pointer before
- * instruction decode. Set the DSP address back to what it should
- * be for this instruction based on its size (2 or 3 32 bit words).
- */
- dsp = dsp_next - NCR53c7x0_insn_size(dcmd);
-
-
- /*
- * Read new SCSI phase from the SBCL lines. Since all of our code uses
- * a WHEN conditional instead of an IF conditional, we don't need to
- * wait for a new REQ.
- */
- sbcl = NCR53c7x0_read8(SBCL_REG) & SBCL_PHASE_MASK;
-
- if (!cmd) {
- action = ACTION_ABORT_PRINT;
- where = "no current command";
- /*
- * The way my SCSI SCRIPTS(tm) are architected, recoverable phase
- * mismatches should only occur where we're doing a multi-byte
- * BMI instruction. Specifically, this means
- *
- * - select messages (a SCSI-I target may ignore additional messages
- * after the IDENTIFY; any target may reject a SDTR or WDTR)
- *
- * - command out (targets may send a message to signal an error
- * condition, or go into STATUSIN after they've decided
- * they don't like the command.
- *
- * - reply_message (targets may reject a multi-byte message in the
- * middle)
- *
- * - data transfer routines (command completion with buffer space
- * left, disconnect message, or error message)
- */
- } else if (((dsp >= cmd->data_transfer_start &&
- dsp < cmd->data_transfer_end)) || dsp == (cmd->residual + 2)) {
- if ((dcmd & (DCMD_TYPE_MASK|DCMD_BMI_OP_MASK|DCMD_BMI_INDIRECT|
- DCMD_BMI_MSG|DCMD_BMI_CD)) == (DCMD_TYPE_BMI|
- DCMD_BMI_OP_MOVE_I)) {
- residual = datapath_residual (host);
- if (hostdata->options & OPTION_DEBUG_DISCONNECT)
- printk ("scsi%d : handling residual transfer (+ %d bytes from DMA FIFO)\n",
- host->host_no, residual);
-
- /*
- * The first instruction is a CALL to the alternate handler for
- * this data transfer phase, so we can do calls to
- * munge_msg_restart as we would if control were passed
- * from normal dynamic code.
- */
- if (dsp != cmd->residual + 2) {
- cmd->residual[0] = ((DCMD_TYPE_TCI | DCMD_TCI_OP_CALL |
- ((dcmd & DCMD_BMI_IO) ? DCMD_TCI_IO : 0)) << 24) |
- DBC_TCI_WAIT_FOR_VALID | DBC_TCI_COMPARE_PHASE;
- cmd->residual[1] = virt_to_bus(hostdata->script)
- + ((dcmd & DCMD_BMI_IO)
- ? hostdata->E_other_in : hostdata->E_other_out);
- }
-
- /*
- * The second instruction is the a data transfer block
- * move instruction, reflecting the pointer and count at the
- * time of the phase mismatch.
- */
- cmd->residual[2] = dbc_dcmd + residual;
- cmd->residual[3] = NCR53c7x0_read32(DNAD_REG) - residual;
-
- /*
- * The third and final instruction is a jump to the instruction
- * which follows the instruction which had to be 'split'
- */
- if (dsp != cmd->residual + 2) {
- cmd->residual[4] = ((DCMD_TYPE_TCI|DCMD_TCI_OP_JUMP)
- << 24) | DBC_TCI_TRUE;
- cmd->residual[5] = virt_to_bus(dsp_next);
- }
-
- /*
- * For the sake of simplicity, transfer control to the
- * conditional CALL at the start of the residual buffer.
- */
- hostdata->dsp = cmd->residual;
- hostdata->dsp_changed = 1;
- action = ACTION_CONTINUE;
- } else {
- where = "non-BMI dynamic DSA code";
- action = ACTION_ABORT_PRINT;
- }
- } else if (dsp == (hostdata->script + hostdata->E_select_msgout / 4 + 2)) {
- /* RGH 290697: Added +2 above, to compensate for the script
- * instruction which disables the selection timer. */
- /* Release ATN */
- NCR53c7x0_write8 (SOCL_REG, 0);
- switch (sbcl) {
- /*
- * Some devices (SQ555 come to mind) grab the IDENTIFY message
- * sent on selection, and decide to go into COMMAND OUT phase
- * rather than accepting the rest of the messages or rejecting
- * them. Handle these devices gracefully.
- */
- case SBCL_PHASE_CMDOUT:
- hostdata->dsp = dsp + 2 /* two _words_ */;
- hostdata->dsp_changed = 1;
- printk ("scsi%d : target %d ignored SDTR and went into COMMAND OUT\n",
- host->host_no, cmd->cmd->device->id);
- cmd->flags &= ~CMD_FLAG_SDTR;
- action = ACTION_CONTINUE;
- break;
- case SBCL_PHASE_MSGIN:
- hostdata->dsp = hostdata->script + hostdata->E_msg_in /
- sizeof(u32);
- hostdata->dsp_changed = 1;
- action = ACTION_CONTINUE;
- break;
- default:
- where="select message out";
- action = ACTION_ABORT_PRINT;
- }
- /*
- * Some SCSI devices will interpret a command as they read the bytes
- * off the SCSI bus, and may decide that the command is Bogus before
- * they've read the entire command off the bus.
- */
- } else if (dsp == hostdata->script + hostdata->E_cmdout_cmdout / sizeof
- (u32)) {
- hostdata->dsp = hostdata->script + hostdata->E_data_transfer /
- sizeof (u32);
- hostdata->dsp_changed = 1;
- action = ACTION_CONTINUE;
- /* FIXME : we need to handle message reject, etc. within msg_respond. */
-#ifdef notyet
- } else if (dsp == hostdata->script + hostdata->E_reply_message) {
- switch (sbcl) {
- /* Any other phase mismatches abort the currently executing command. */
-#endif
- } else {
- where = "unknown location";
- action = ACTION_ABORT_PRINT;
- }
-
- /* Flush DMA FIFO */
- if (!hostdata->dstat_valid) {
- hostdata->dstat = NCR53c7x0_read8(DSTAT_REG);
- hostdata->dstat_valid = 1;
- }
- if (!(hostdata->dstat & DSTAT_DFE)) {
- /* Really need to check this out for 710 RGH */
- NCR53c7x0_write8 (CTEST8_REG, CTEST8_10_CLF);
- while (NCR53c7x0_read8 (CTEST8_REG) & CTEST8_10_CLF);
- hostdata->dstat |= DSTAT_DFE;
- }
-
- switch (action) {
- case ACTION_ABORT_PRINT:
- printk("scsi%d : %s : unexpected phase %s.\n",
- host->host_no, where ? where : "unknown location",
- sbcl_to_phase(sbcl));
- print_lots (host);
- /* Fall through to ACTION_ABORT */
- case ACTION_ABORT:
- abort_connected (host);
- break;
- case ACTION_CONTINUE:
- break;
- }
-
-#if 0
- if (hostdata->dsp_changed) {
- printk("scsi%d: new dsp 0x%p\n", host->host_no, hostdata->dsp);
- print_insn (host, hostdata->dsp, "", 1);
- }
-#endif
-}
-
-/*
- * Function : static void intr_bf (struct Scsi_Host *host,
- * struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : handle BUS FAULT interrupts
- *
- * Inputs : host, cmd - host and NCR command causing the interrupt, cmd
- * may be NULL.
- */
-
-static void
-intr_bf (struct Scsi_Host *host, struct NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- u32 *dsp,
- *next_dsp, /* Current dsp */
- *dsa,
- dbc_dcmd; /* DCMD (high eight bits) + DBC */
- char *reason = NULL;
- /* Default behavior is for a silent error, with a retry until we've
- exhausted retries. */
- enum {MAYBE, ALWAYS, NEVER} retry = MAYBE;
- int report = 0;
- NCR53c7x0_local_setup(host);
-
- dbc_dcmd = NCR53c7x0_read32 (DBC_REG);
- next_dsp = bus_to_virt (NCR53c7x0_read32(DSP_REG));
- dsp = next_dsp - NCR53c7x0_insn_size ((dbc_dcmd >> 24) & 0xff);
-/* FIXME - check chip type */
- dsa = bus_to_virt (NCR53c7x0_read32(DSA_REG));
-
- /*
- * Bus faults can be caused by either a Bad Address or
- * Target Abort. We should check the Received Target Abort
- * bit of the PCI status register and Master Abort Bit.
- *
- * - Master Abort bit indicates that no device claimed
- * the address with DEVSEL within five clocks
- *
- * - Target Abort bit indicates that a target claimed it,
- * but changed its mind once it saw the byte enables.
- *
- */
-
- /* 53c710, not PCI system */
- report = 1;
- reason = "Unknown";
-
-#ifndef notyet
- report = 1;
-#endif
- if (report && reason)
- {
- printk(KERN_ALERT "scsi%d : BUS FAULT reason = %s\n",
- host->host_no, reason ? reason : "unknown");
- print_lots (host);
- }
-
-#ifndef notyet
- retry = NEVER;
-#endif
-
- /*
- * TODO : we should attempt to recover from any spurious bus
- * faults. After X retries, we should figure that things are
- * sufficiently wedged, and call NCR53c7xx_reset.
- *
- * This code should only get executed once we've decided that we
- * cannot retry.
- */
-
- if (retry == NEVER) {
- printk(KERN_ALERT " mail richard@sleepie.demon.co.uk\n");
- FATAL (host);
- }
-}
-
-/*
- * Function : static void intr_dma (struct Scsi_Host *host,
- * struct NCR53c7x0_cmd *cmd)
- *
- * Purpose : handle all DMA interrupts, indicated by the setting
- * of the DIP bit in the ISTAT register.
- *
- * Inputs : host, cmd - host and NCR command causing the interrupt, cmd
- * may be NULL.
- */
-
-static void
-intr_dma (struct Scsi_Host *host, struct NCR53c7x0_cmd *cmd) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned char dstat; /* DSTAT */
- u32 *dsp,
- *next_dsp, /* Current dsp */
- *dsa,
- dbc_dcmd; /* DCMD (high eight bits) + DBC */
- int tmp;
- unsigned long flags;
- NCR53c7x0_local_setup(host);
-
- if (!hostdata->dstat_valid) {
- hostdata->dstat = NCR53c7x0_read8(DSTAT_REG);
- hostdata->dstat_valid = 1;
- }
-
- dstat = hostdata->dstat;
-
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk("scsi%d : DSTAT=0x%x\n", host->host_no, (int) dstat);
-
- dbc_dcmd = NCR53c7x0_read32 (DBC_REG);
- next_dsp = bus_to_virt(NCR53c7x0_read32(DSP_REG));
- dsp = next_dsp - NCR53c7x0_insn_size ((dbc_dcmd >> 24) & 0xff);
-/* XXX - check chip type */
- dsa = bus_to_virt(NCR53c7x0_read32(DSA_REG));
-
- /*
- * DSTAT_ABRT is the aborted interrupt. This is set whenever the
- * SCSI chip is aborted.
- *
- * With NCR53c700 and NCR53c700-66 style chips, we should only
- * get this when the chip is currently running the accept
- * reselect/select code and we have set the abort bit in the
- * ISTAT register.
- *
- */
-
- if (dstat & DSTAT_ABRT) {
-#if 0
- /* XXX - add code here to deal with normal abort */
- if ((hostdata->options & OPTION_700) && (hostdata->state ==
- STATE_ABORTING)) {
- } else
-#endif
- {
- printk(KERN_ALERT "scsi%d : unexpected abort interrupt at\n"
- " ", host->host_no);
- print_insn (host, dsp, KERN_ALERT "s ", 1);
- FATAL (host);
- }
- }
-
- /*
- * DSTAT_SSI is the single step interrupt. Should be generated
- * whenever we have single stepped or are tracing.
- */
-
- if (dstat & DSTAT_SSI) {
- if (hostdata->options & OPTION_DEBUG_TRACE) {
- /* Don't print instr. until we write DSP at end of intr function */
- } else if (hostdata->options & OPTION_DEBUG_SINGLE) {
- print_insn (host, dsp, "s ", 0);
- local_irq_save(flags);
-/* XXX - should we do this, or can we get away with writing dsp? */
-
- NCR53c7x0_write8 (DCNTL_REG, (NCR53c7x0_read8(DCNTL_REG) &
- ~DCNTL_SSM) | DCNTL_STD);
- local_irq_restore(flags);
- } else {
- printk(KERN_ALERT "scsi%d : unexpected single step interrupt at\n"
- " ", host->host_no);
- print_insn (host, dsp, KERN_ALERT "", 1);
- printk(KERN_ALERT " mail drew@PoohSticks.ORG\n");
- FATAL (host);
- }
- }
-
- /*
- * DSTAT_IID / DSTAT_OPC (same bit, same meaning, only the name
- * is different) is generated whenever an illegal instruction is
- * encountered.
- *
- * XXX - we may want to emulate INTFLY here, so we can use
- * the same SCSI SCRIPT (tm) for NCR53c710 through NCR53c810
- * chips.
- */
-
- if (dstat & DSTAT_OPC) {
- /*
- * Ascertain if this IID interrupts occurred before or after a STO
- * interrupt. Since the interrupt handling code now leaves
- * DSP unmodified until _after_ all stacked interrupts have been
- * processed, reading the DSP returns the original DSP register.
- * This means that if dsp lies between the select code, and
- * message out following the selection code (where the IID interrupt
- * would have to have occurred by due to the implicit wait for REQ),
- * we have an IID interrupt resulting from a STO condition and
- * can ignore it.
- */
-
- if (((dsp >= (hostdata->script + hostdata->E_select / sizeof(u32))) &&
- (dsp <= (hostdata->script + hostdata->E_select_msgout /
- sizeof(u32) + 8))) || (hostdata->test_running == 2)) {
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : ignoring DSTAT_IID for SSTAT_STO\n",
- host->host_no);
- if (hostdata->expecting_iid) {
- hostdata->expecting_iid = 0;
- hostdata->idle = 1;
- if (hostdata->test_running == 2) {
- hostdata->test_running = 0;
- hostdata->test_completed = 3;
- } else if (cmd)
- abnormal_finished (cmd, DID_BAD_TARGET << 16);
- } else {
- hostdata->expecting_sto = 1;
- }
- /*
- * We can't guarantee we'll be able to execute the WAIT DISCONNECT
- * instruction within the 3.4us of bus free and arbitration delay
- * that a target can RESELECT in and assert REQ after we've dropped
- * ACK. If this happens, we'll get an illegal instruction interrupt.
- * Doing away with the WAIT DISCONNECT instructions broke everything,
- * so instead I'll settle for moving one WAIT DISCONNECT a few
- * instructions closer to the CLEAR ACK before it to minimize the
- * chances of this happening, and handle it if it occurs anyway.
- *
- * Simply continue with what we were doing, and control should
- * be transferred to the schedule routine which will ultimately
- * pass control onto the reselection or selection (not yet)
- * code.
- */
- } else if (dbc_dcmd == 0x48000000 && (NCR53c7x0_read8 (SBCL_REG) &
- SBCL_REQ)) {
- if (!(hostdata->options & OPTION_NO_PRINT_RACE))
- {
- printk("scsi%d: REQ before WAIT DISCONNECT IID\n",
- host->host_no);
- hostdata->options |= OPTION_NO_PRINT_RACE;
- }
- } else {
- printk(KERN_ALERT "scsi%d : invalid instruction\n", host->host_no);
- print_lots (host);
- printk(KERN_ALERT " mail Richard@sleepie.demon.co.uk with ALL\n"
- " boot messages and diagnostic output\n");
- FATAL (host);
- }
- }
-
- /*
- * DSTAT_BF are bus fault errors. DSTAT_800_BF is valid for 710 also.
- */
-
- if (dstat & DSTAT_800_BF) {
- intr_bf (host, cmd);
- }
-
-
- /*
- * DSTAT_SIR interrupts are generated by the execution of
- * the INT instruction. Since the exact values available
- * are determined entirely by the SCSI script running,
- * and are local to a particular script, a unique handler
- * is called for each script.
- */
-
- if (dstat & DSTAT_SIR) {
- if (hostdata->options & OPTION_DEBUG_INTR)
- printk ("scsi%d : DSTAT_SIR\n", host->host_no);
- switch ((tmp = hostdata->dstat_sir_intr (host, cmd))) {
- case SPECIFIC_INT_NOTHING:
- case SPECIFIC_INT_RESTART:
- break;
- case SPECIFIC_INT_ABORT:
- abort_connected(host);
- break;
- case SPECIFIC_INT_PANIC:
- printk(KERN_ALERT "scsi%d : failure at ", host->host_no);
- print_insn (host, dsp, KERN_ALERT "", 1);
- printk(KERN_ALERT " dstat_sir_intr() returned SPECIFIC_INT_PANIC\n");
- FATAL (host);
- break;
- case SPECIFIC_INT_BREAK:
- intr_break (host, cmd);
- break;
- default:
- printk(KERN_ALERT "scsi%d : failure at ", host->host_no);
- print_insn (host, dsp, KERN_ALERT "", 1);
- printk(KERN_ALERT" dstat_sir_intr() returned unknown value %d\n",
- tmp);
- FATAL (host);
- }
- }
-}
-
-/*
- * Function : static int print_insn (struct Scsi_Host *host,
- * u32 *insn, int kernel)
- *
- * Purpose : print numeric representation of the instruction pointed
- * to by insn to the debugging or kernel message buffer
- * as appropriate.
- *
- * If desired, a user level program can interpret this
- * information.
- *
- * Inputs : host, insn - host, pointer to instruction, prefix -
- * string to prepend, kernel - use printk instead of debugging buffer.
- *
- * Returns : size, in u32s, of instruction printed.
- */
-
-/*
- * FIXME: should change kernel parameter so that it takes an ENUM
- * specifying severity - either KERN_ALERT or KERN_PANIC so
- * all panic messages are output with the same severity.
- */
-
-static int
-print_insn (struct Scsi_Host *host, const u32 *insn,
- const char *prefix, int kernel) {
- char buf[160], /* Temporary buffer and pointer. ICKY
- arbitrary length. */
-
-
- *tmp;
- unsigned char dcmd; /* dcmd register for *insn */
- int size;
-
- /*
- * Check to see if the instruction pointer is not bogus before
- * indirecting through it; avoiding red-zone at start of
- * memory.
- *
- * FIXME: icky magic needs to happen here on non-intel boxes which
- * don't have kernel memory mapped in like this. Might be reasonable
- * to use vverify()?
- */
-
- if (virt_to_phys((void *)insn) < PAGE_SIZE ||
- virt_to_phys((void *)(insn + 8)) > virt_to_phys(high_memory) ||
- ((((dcmd = (insn[0] >> 24) & 0xff) & DCMD_TYPE_MMI) == DCMD_TYPE_MMI) &&
- virt_to_phys((void *)(insn + 12)) > virt_to_phys(high_memory))) {
- size = 0;
- sprintf (buf, "%s%p: address out of range\n",
- prefix, insn);
- } else {
-/*
- * FIXME : (void *) cast in virt_to_bus should be unnecessary, because
- * it should take const void * as argument.
- */
-#if !defined(CONFIG_MVME16x) && !defined(CONFIG_BVME6000)
- sprintf(buf, "%s0x%lx (virt 0x%p) : 0x%08x 0x%08x (virt 0x%p)",
- (prefix ? prefix : ""), virt_to_bus((void *) insn), insn,
- insn[0], insn[1], bus_to_virt (insn[1]));
-#else
- /* Remove virtual addresses to reduce output, as they are the same */
- sprintf(buf, "%s0x%x (+%x) : 0x%08x 0x%08x",
- (prefix ? prefix : ""), (u32)insn, ((u32)insn -
- (u32)&(((struct NCR53c7x0_hostdata *)host->hostdata[0])->script))/4,
- insn[0], insn[1]);
-#endif
- tmp = buf + strlen(buf);
- if ((dcmd & DCMD_TYPE_MASK) == DCMD_TYPE_MMI) {
-#if !defined(CONFIG_MVME16x) && !defined(CONFIG_BVME6000)
- sprintf (tmp, " 0x%08x (virt 0x%p)\n", insn[2],
- bus_to_virt(insn[2]));
-#else
- /* Remove virtual addr to reduce output, as it is the same */
- sprintf (tmp, " 0x%08x\n", insn[2]);
-#endif
- size = 3;
- } else {
- sprintf (tmp, "\n");
- size = 2;
- }
- }
-
- if (kernel)
- printk ("%s", buf);
-#ifdef NCR_DEBUG
- else {
- size_t len = strlen(buf);
- debugger_kernel_write(host, buf, len);
- }
-#endif
- return size;
-}
-
-/*
- * Function : int NCR53c7xx_abort (Scsi_Cmnd *cmd)
- *
- * Purpose : Abort an errant SCSI command, doing all necessary
- * cleanup of the issue_queue, running_list, shared Linux/NCR
- * dsa issue and reconnect queues.
- *
- * Inputs : cmd - command to abort, code - entire result field
- *
- * Returns : 0 on success, -1 on failure.
- */
-
-int
-NCR53c7xx_abort (Scsi_Cmnd *cmd) {
- NCR53c7x0_local_declare();
- struct Scsi_Host *host = cmd->device->host;
- struct NCR53c7x0_hostdata *hostdata = host ? (struct NCR53c7x0_hostdata *)
- host->hostdata[0] : NULL;
- unsigned long flags;
- struct NCR53c7x0_cmd *curr, **prev;
- Scsi_Cmnd *me, **last;
-#if 0
- static long cache_pid = -1;
-#endif
-
-
- if (!host) {
- printk ("Bogus SCSI command pid %ld; no host structure\n",
- cmd->pid);
- return SCSI_ABORT_ERROR;
- } else if (!hostdata) {
- printk ("Bogus SCSI host %d; no hostdata\n", host->host_no);
- return SCSI_ABORT_ERROR;
- }
- NCR53c7x0_local_setup(host);
-
-/*
- * CHECK : I don't think that reading ISTAT will unstack any interrupts,
- * since we need to write the INTF bit to clear it, and SCSI/DMA
- * interrupts don't clear until we read SSTAT/SIST and DSTAT registers.
- *
- * See that this is the case. Appears to be correct on the 710, at least.
- *
- * I suspect that several of our failures may be coming from a new fatal
- * interrupt (possibly due to a phase mismatch) happening after we've left
- * the interrupt handler, but before the PIC has had the interrupt condition
- * cleared.
- */
-
- if (NCR53c7x0_read8(hostdata->istat) & (ISTAT_DIP|ISTAT_SIP)) {
- printk ("scsi%d : dropped interrupt for command %ld\n", host->host_no,
- cmd->pid);
- NCR53c7x0_intr (host->irq, NULL, NULL);
- return SCSI_ABORT_BUSY;
- }
-
- local_irq_save(flags);
-#if 0
- if (cache_pid == cmd->pid)
- panic ("scsi%d : bloody fetus %d\n", host->host_no, cmd->pid);
- else
- cache_pid = cmd->pid;
-#endif
-
-
-/*
- * The command could be hiding in the issue_queue. This would be very
- * nice, as commands can't be moved from the high level driver's issue queue
- * into the shared queue until an interrupt routine is serviced, and this
- * moving is atomic.
- *
- * If this is the case, we don't have to worry about anything - we simply
- * pull the command out of the old queue, and call it aborted.
- */
-
- for (me = (Scsi_Cmnd *) hostdata->issue_queue,
- last = (Scsi_Cmnd **) &(hostdata->issue_queue);
- me && me != cmd; last = (Scsi_Cmnd **)&(me->SCp.ptr),
- me = (Scsi_Cmnd *)me->SCp.ptr);
-
- if (me) {
- *last = (Scsi_Cmnd *) me->SCp.ptr;
- if (me->host_scribble) {
- ((struct NCR53c7x0_cmd *)me->host_scribble)->next = hostdata->free;
- hostdata->free = (struct NCR53c7x0_cmd *) me->host_scribble;
- me->host_scribble = NULL;
- }
- cmd->result = DID_ABORT << 16;
- cmd->scsi_done(cmd);
- printk ("scsi%d : found command %ld in Linux issue queue\n",
- host->host_no, me->pid);
- local_irq_restore(flags);
- run_process_issue_queue();
- return SCSI_ABORT_SUCCESS;
- }
-
-/*
- * That failing, the command could be in our list of already executing
- * commands. If this is the case, drastic measures are called for.
- */
-
- for (curr = (struct NCR53c7x0_cmd *) hostdata->running_list,
- prev = (struct NCR53c7x0_cmd **) &(hostdata->running_list);
- curr && curr->cmd != cmd; prev = (struct NCR53c7x0_cmd **)
- &(curr->next), curr = (struct NCR53c7x0_cmd *) curr->next);
-
- if (curr) {
- if ((curr->result & 0xff) != 0xff && (curr->result & 0xff00) != 0xff00) {
- cmd->result = curr->result;
- if (prev)
- *prev = (struct NCR53c7x0_cmd *) curr->next;
- curr->next = (struct NCR53c7x0_cmd *) hostdata->free;
- cmd->host_scribble = NULL;
- hostdata->free = curr;
- cmd->scsi_done(cmd);
- printk ("scsi%d : found finished command %ld in running list\n",
- host->host_no, cmd->pid);
- local_irq_restore(flags);
- return SCSI_ABORT_NOT_RUNNING;
- } else {
- printk ("scsi%d : DANGER : command running, can not abort.\n",
- cmd->device->host->host_no);
- local_irq_restore(flags);
- return SCSI_ABORT_BUSY;
- }
- }
-
-/*
- * And if we couldn't find it in any of our queues, it must have been
- * a dropped interrupt.
- */
-
- curr = (struct NCR53c7x0_cmd *) cmd->host_scribble;
- if (curr) {
- curr->next = hostdata->free;
- hostdata->free = curr;
- cmd->host_scribble = NULL;
- }
-
- if (curr == NULL || ((curr->result & 0xff00) == 0xff00) ||
- ((curr->result & 0xff) == 0xff)) {
- printk ("scsi%d : did this command ever run?\n", host->host_no);
- cmd->result = DID_ABORT << 16;
- } else {
- printk ("scsi%d : probably lost INTFLY, normal completion\n",
- host->host_no);
- cmd->result = curr->result;
-/*
- * FIXME : We need to add an additional flag which indicates if a
- * command was ever counted as BUSY, so if we end up here we can
- * decrement the busy count if and only if it is necessary.
- */
- --hostdata->busy[cmd->device->id][cmd->device->lun];
- }
- local_irq_restore(flags);
- cmd->scsi_done(cmd);
-
-/*
- * We need to run process_issue_queue since termination of this command
- * may allow another queued command to execute first?
- */
- return SCSI_ABORT_NOT_RUNNING;
-}
-
-/*
- * Function : int NCR53c7xx_reset (Scsi_Cmnd *cmd)
- *
- * Purpose : perform a hard reset of the SCSI bus and NCR
- * chip.
- *
- * Inputs : cmd - command which caused the SCSI RESET
- *
- * Returns : 0 on success.
- */
-
-int
-NCR53c7xx_reset (Scsi_Cmnd *cmd, unsigned int reset_flags) {
- NCR53c7x0_local_declare();
- unsigned long flags;
- int found = 0;
- struct NCR53c7x0_cmd * c;
- Scsi_Cmnd *tmp;
- /*
- * When we call scsi_done(), it's going to wake up anything sleeping on the
- * resources which were in use by the aborted commands, and we'll start to
- * get new commands.
- *
- * We can't let this happen until after we've re-initialized the driver
- * structures, and can't reinitialize those structures until after we've
- * dealt with their contents.
- *
- * So, we need to find all of the commands which were running, stick
- * them on a linked list of completed commands (we'll use the host_scribble
- * pointer), do our reinitialization, and then call the done function for
- * each command.
- */
- Scsi_Cmnd *nuke_list = NULL;
- struct Scsi_Host *host = cmd->device->host;
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) host->hostdata[0];
-
- NCR53c7x0_local_setup(host);
- local_irq_save(flags);
- ncr_halt (host);
- print_lots (host);
- dump_events (host, 30);
- ncr_scsi_reset (host);
- for (tmp = nuke_list = return_outstanding_commands (host, 1 /* free */,
- 0 /* issue */ ); tmp; tmp = (Scsi_Cmnd *) tmp->SCp.buffer)
- if (tmp == cmd) {
- found = 1;
- break;
- }
-
- /*
- * If we didn't find the command which caused this reset in our running
- * list, then we've lost it. See that it terminates normally anyway.
- */
- if (!found) {
- c = (struct NCR53c7x0_cmd *) cmd->host_scribble;
- if (c) {
- cmd->host_scribble = NULL;
- c->next = hostdata->free;
- hostdata->free = c;
- } else
- printk ("scsi%d: lost command %ld\n", host->host_no, cmd->pid);
- cmd->SCp.buffer = (struct scatterlist *) nuke_list;
- nuke_list = cmd;
- }
-
- NCR53c7x0_driver_init (host);
- hostdata->soft_reset (host);
- if (hostdata->resets == 0)
- disable(host);
- else if (hostdata->resets != -1)
- --hostdata->resets;
- local_irq_restore(flags);
- for (; nuke_list; nuke_list = tmp) {
- tmp = (Scsi_Cmnd *) nuke_list->SCp.buffer;
- nuke_list->result = DID_RESET << 16;
- nuke_list->scsi_done (nuke_list);
- }
- local_irq_restore(flags);
- return SCSI_RESET_SUCCESS;
-}
-
-/*
- * The NCR SDMS bios follows Annex A of the SCSI-CAM draft, and
- * therefore shares the scsicam_bios_param function.
- */
-
-/*
- * Function : int insn_to_offset (Scsi_Cmnd *cmd, u32 *insn)
- *
- * Purpose : convert instructions stored at NCR pointer into data
- * pointer offset.
- *
- * Inputs : cmd - SCSI command; insn - pointer to instruction. Either current
- * DSP, or saved data pointer.
- *
- * Returns : offset on success, -1 on failure.
- */
-
-
-static int
-insn_to_offset (Scsi_Cmnd *cmd, u32 *insn) {
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) cmd->device->host->hostdata[0];
- struct NCR53c7x0_cmd *ncmd =
- (struct NCR53c7x0_cmd *) cmd->host_scribble;
- int offset = 0, buffers;
- struct scatterlist *segment;
- char *ptr;
- int found = 0;
-
-/*
- * With the current code implementation, if the insn is inside dynamically
- * generated code, the data pointer will be the instruction preceding
- * the next transfer segment.
- */
-
- if (!check_address ((unsigned long) ncmd, sizeof (struct NCR53c7x0_cmd)) &&
- ((insn >= ncmd->data_transfer_start &&
- insn < ncmd->data_transfer_end) ||
- (insn >= ncmd->residual &&
- insn < (ncmd->residual +
- sizeof(ncmd->residual))))) {
- ptr = bus_to_virt(insn[3]);
-
- if ((buffers = cmd->use_sg)) {
- for (offset = 0,
- segment = (struct scatterlist *) cmd->request_buffer;
- buffers && !((found = ((ptr >= (char *)page_address(segment->page)+segment->offset) &&
- (ptr < ((char *)page_address(segment->page)+segment->offset+segment->length)))));
- --buffers, offset += segment->length, ++segment)
-#if 0
- printk("scsi%d: comparing 0x%p to 0x%p\n",
- cmd->device->host->host_no, saved, page_address(segment->page+segment->offset));
-#else
- ;
-#endif
- offset += ptr - ((char *)page_address(segment->page)+segment->offset);
- } else {
- found = 1;
- offset = ptr - (char *) (cmd->request_buffer);
- }
- } else if ((insn >= hostdata->script +
- hostdata->E_data_transfer / sizeof(u32)) &&
- (insn <= hostdata->script +
- hostdata->E_end_data_transfer / sizeof(u32))) {
- found = 1;
- offset = 0;
- }
- return found ? offset : -1;
-}
-
-
-
-/*
- * Function : void print_progress (Scsi_Cmnd *cmd)
- *
- * Purpose : print the current location of the saved data pointer
- *
- * Inputs : cmd - command we are interested in
- *
- */
-
-static void
-print_progress (Scsi_Cmnd *cmd) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_cmd *ncmd =
- (struct NCR53c7x0_cmd *) cmd->host_scribble;
- int offset, i;
- char *where;
- u32 *ptr;
- NCR53c7x0_local_setup (cmd->device->host);
-
- if (check_address ((unsigned long) ncmd,sizeof (struct NCR53c7x0_cmd)) == 0)
- {
- printk("\nNCR53c7x0_cmd fields:\n");
- printk(" bounce.len=0x%x, addr=0x%0x, buf[]=0x%02x %02x %02x %02x\n",
- ncmd->bounce.len, ncmd->bounce.addr, ncmd->bounce.buf[0],
- ncmd->bounce.buf[1], ncmd->bounce.buf[2], ncmd->bounce.buf[3]);
- printk(" result=%04x, cdb[0]=0x%02x\n", ncmd->result, ncmd->cmnd[0]);
- }
-
- for (i = 0; i < 2; ++i) {
- if (check_address ((unsigned long) ncmd,
- sizeof (struct NCR53c7x0_cmd)) == -1)
- continue;
- if (!i) {
- where = "saved";
- ptr = bus_to_virt(ncmd->saved_data_pointer);
- } else {
- where = "active";
- ptr = bus_to_virt (NCR53c7x0_read32 (DSP_REG) -
- NCR53c7x0_insn_size (NCR53c7x0_read8 (DCMD_REG)) *
- sizeof(u32));
- }
- offset = insn_to_offset (cmd, ptr);
-
- if (offset != -1)
- printk ("scsi%d : %s data pointer at offset %d\n",
- cmd->device->host->host_no, where, offset);
- else {
- int size;
- printk ("scsi%d : can't determine %s data pointer offset\n",
- cmd->device->host->host_no, where);
- if (ncmd) {
- size = print_insn (cmd->device->host,
- bus_to_virt(ncmd->saved_data_pointer), "", 1);
- print_insn (cmd->device->host,
- bus_to_virt(ncmd->saved_data_pointer) + size * sizeof(u32),
- "", 1);
- }
- }
- }
-}
-
-
-static void
-print_dsa (struct Scsi_Host *host, u32 *dsa, const char *prefix) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- int i, len;
- char *ptr;
- Scsi_Cmnd *cmd;
-
- if (check_address ((unsigned long) dsa, hostdata->dsa_end -
- hostdata->dsa_start) == -1) {
- printk("scsi%d : bad dsa virt 0x%p\n", host->host_no, dsa);
- return;
- }
- printk("%sscsi%d : dsa at phys 0x%lx (virt 0x%p)\n"
- " + %d : dsa_msgout length = %u, data = 0x%x (virt 0x%p)\n" ,
- prefix ? prefix : "",
- host->host_no, virt_to_bus (dsa), dsa, hostdata->dsa_msgout,
- dsa[hostdata->dsa_msgout / sizeof(u32)],
- dsa[hostdata->dsa_msgout / sizeof(u32) + 1],
- bus_to_virt (dsa[hostdata->dsa_msgout / sizeof(u32) + 1]));
-
- /*
- * Only print messages if they're sane in length so we don't
- * blow the kernel printk buffer on something which won't buy us
- * anything.
- */
-
- if (dsa[hostdata->dsa_msgout / sizeof(u32)] <
- sizeof (hostdata->free->select))
- for (i = dsa[hostdata->dsa_msgout / sizeof(u32)],
- ptr = bus_to_virt (dsa[hostdata->dsa_msgout / sizeof(u32) + 1]);
- i > 0 && !check_address ((unsigned long) ptr, 1);
- ptr += len, i -= len) {
- printk(" ");
- len = spi_print_msg(ptr);
- printk("\n");
- if (!len)
- break;
- }
-
- printk(" + %d : select_indirect = 0x%x\n",
- hostdata->dsa_select, dsa[hostdata->dsa_select / sizeof(u32)]);
- cmd = (Scsi_Cmnd *) bus_to_virt(dsa[hostdata->dsa_cmnd / sizeof(u32)]);
- printk(" + %d : dsa_cmnd = 0x%x ", hostdata->dsa_cmnd,
- (u32) virt_to_bus(cmd));
- /* XXX Maybe we should access cmd->host_scribble->result here. RGH */
- if (cmd) {
- printk(" result = 0x%x, target = %d, lun = %d, cmd = ",
- cmd->result, cmd->device->id, cmd->device->lun);
- __scsi_print_command(cmd->cmnd);
- } else
- printk("\n");
- printk(" + %d : dsa_next = 0x%x\n", hostdata->dsa_next,
- dsa[hostdata->dsa_next / sizeof(u32)]);
- if (cmd) {
- printk("scsi%d target %d : sxfer_sanity = 0x%x, scntl3_sanity = 0x%x\n"
- " script : ",
- host->host_no, cmd->device->id,
- hostdata->sync[cmd->device->id].sxfer_sanity,
- hostdata->sync[cmd->device->id].scntl3_sanity);
- for (i = 0; i < (sizeof(hostdata->sync[cmd->device->id].script) / 4); ++i)
- printk ("0x%x ", hostdata->sync[cmd->device->id].script[i]);
- printk ("\n");
- print_progress (cmd);
- }
-}
-/*
- * Function : void print_queues (Scsi_Host *host)
- *
- * Purpose : print the contents of the NCR issue and reconnect queues
- *
- * Inputs : host - SCSI host we are interested in
- *
- */
-
-static void
-print_queues (struct Scsi_Host *host) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- u32 *dsa, *next_dsa;
- volatile u32 *ncrcurrent;
- int left;
- Scsi_Cmnd *cmd, *next_cmd;
- unsigned long flags;
-
- printk ("scsi%d : issue queue\n", host->host_no);
-
- for (left = host->can_queue, cmd = (Scsi_Cmnd *) hostdata->issue_queue;
- left >= 0 && cmd;
- cmd = next_cmd) {
- next_cmd = (Scsi_Cmnd *) cmd->SCp.ptr;
- local_irq_save(flags);
- if (cmd->host_scribble) {
- if (check_address ((unsigned long) (cmd->host_scribble),
- sizeof (cmd->host_scribble)) == -1)
- printk ("scsi%d: scsi pid %ld bad pointer to NCR53c7x0_cmd\n",
- host->host_no, cmd->pid);
- /* print_dsa does sanity check on address, no need to check */
- else
- print_dsa (host, ((struct NCR53c7x0_cmd *) cmd->host_scribble)
- -> dsa, "");
- } else
- printk ("scsi%d : scsi pid %ld for target %d lun %d has no NCR53c7x0_cmd\n",
- host->host_no, cmd->pid, cmd->device->id, cmd->device->lun);
- local_irq_restore(flags);
- }
-
- if (left <= 0) {
- printk ("scsi%d : loop detected in issue queue\n",
- host->host_no);
- }
-
- /*
- * Traverse the NCR reconnect and start DSA structures, printing out
- * each element until we hit the end or detect a loop. Currently,
- * the reconnect structure is a linked list; and the start structure
- * is an array. Eventually, the reconnect structure will become a
- * list as well, since this simplifies the code.
- */
-
- printk ("scsi%d : schedule dsa array :\n", host->host_no);
- for (left = host->can_queue, ncrcurrent = hostdata->schedule;
- left > 0; ncrcurrent += 2, --left)
- if (ncrcurrent[0] != hostdata->NOP_insn)
-/* FIXME : convert pointer to dsa_begin to pointer to dsa. */
- print_dsa (host, bus_to_virt (ncrcurrent[1] -
- (hostdata->E_dsa_code_begin -
- hostdata->E_dsa_code_template)), "");
- printk ("scsi%d : end schedule dsa array\n", host->host_no);
-
- printk ("scsi%d : reconnect_dsa_head :\n", host->host_no);
-
- for (left = host->can_queue,
- dsa = bus_to_virt (hostdata->reconnect_dsa_head);
- left >= 0 && dsa;
- dsa = next_dsa) {
- local_irq_save(flags);
- if (check_address ((unsigned long) dsa, sizeof(dsa)) == -1) {
- printk ("scsi%d: bad DSA pointer 0x%p", host->host_no,
- dsa);
- next_dsa = NULL;
- }
- else
- {
- next_dsa = bus_to_virt(dsa[hostdata->dsa_next / sizeof(u32)]);
- print_dsa (host, dsa, "");
- }
- local_irq_restore(flags);
- }
- printk ("scsi%d : end reconnect_dsa_head\n", host->host_no);
- if (left < 0)
- printk("scsi%d: possible loop in ncr reconnect list\n",
- host->host_no);
-}
-
-static void
-print_lots (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) host->hostdata[0];
- u32 *dsp_next, *dsp, *dsa, dbc_dcmd;
- unsigned char dcmd, sbcl;
- int i, size;
- NCR53c7x0_local_setup(host);
-
- if ((dsp_next = bus_to_virt(NCR53c7x0_read32 (DSP_REG)))) {
- dbc_dcmd = NCR53c7x0_read32(DBC_REG);
- dcmd = (dbc_dcmd & 0xff000000) >> 24;
- dsp = dsp_next - NCR53c7x0_insn_size(dcmd);
- dsa = bus_to_virt(NCR53c7x0_read32(DSA_REG));
- sbcl = NCR53c7x0_read8 (SBCL_REG);
-
- /*
- * For the 53c710, the following will report value 0 for SCNTL3
- * and STEST0 - we don't have these registers.
- */
- printk ("scsi%d : DCMD|DBC=0x%x, DNAD=0x%x (virt 0x%p)\n"
- " DSA=0x%lx (virt 0x%p)\n"
- " DSPS=0x%x, TEMP=0x%x (virt 0x%p), DMODE=0x%x\n"
- " SXFER=0x%x, SCNTL3=0x%x\n"
- " %s%s%sphase=%s, %d bytes in SCSI FIFO\n"
- " SCRATCH=0x%x, saved2_dsa=0x%0lx\n",
- host->host_no, dbc_dcmd, NCR53c7x0_read32(DNAD_REG),
- bus_to_virt(NCR53c7x0_read32(DNAD_REG)),
- virt_to_bus(dsa), dsa,
- NCR53c7x0_read32(DSPS_REG), NCR53c7x0_read32(TEMP_REG),
- bus_to_virt (NCR53c7x0_read32(TEMP_REG)),
- (int) NCR53c7x0_read8(hostdata->dmode),
- (int) NCR53c7x0_read8(SXFER_REG),
- ((hostdata->chip / 100) == 8) ?
- (int) NCR53c7x0_read8(SCNTL3_REG_800) : 0,
- (sbcl & SBCL_BSY) ? "BSY " : "",
- (sbcl & SBCL_SEL) ? "SEL " : "",
- (sbcl & SBCL_REQ) ? "REQ " : "",
- sstat2_to_phase(NCR53c7x0_read8 (((hostdata->chip / 100) == 8) ?
- SSTAT1_REG : SSTAT2_REG)),
- (NCR53c7x0_read8 ((hostdata->chip / 100) == 8 ?
- SSTAT1_REG : SSTAT2_REG) & SSTAT2_FF_MASK) >> SSTAT2_FF_SHIFT,
- ((hostdata->chip / 100) == 8) ? NCR53c7x0_read8 (STEST0_REG_800) :
- NCR53c7x0_read32(SCRATCHA_REG_800),
- hostdata->saved2_dsa);
- printk ("scsi%d : DSP 0x%lx (virt 0x%p) ->\n", host->host_no,
- virt_to_bus(dsp), dsp);
- for (i = 6; i > 0; --i, dsp += size)
- size = print_insn (host, dsp, "", 1);
- if (NCR53c7x0_read8 (SCNTL1_REG) & SCNTL1_CON) {
- if ((hostdata->chip / 100) == 8)
- printk ("scsi%d : connected (SDID=0x%x, SSID=0x%x)\n",
- host->host_no, NCR53c7x0_read8 (SDID_REG_800),
- NCR53c7x0_read8 (SSID_REG_800));
- else
- printk ("scsi%d : connected (SDID=0x%x)\n",
- host->host_no, NCR53c7x0_read8 (SDID_REG_700));
- print_dsa (host, dsa, "");
- }
-
-#if 1
- print_queues (host);
-#endif
- }
-}
-
-/*
- * Function : static int shutdown (struct Scsi_Host *host)
- *
- * Purpose : does a clean (we hope) shutdown of the NCR SCSI
- * chip. Use prior to dumping core, unloading the NCR driver,
- *
- * Returns : 0 on success
- */
-static int
-shutdown (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- unsigned long flags;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- NCR53c7x0_local_setup(host);
- local_irq_save(flags);
-/* Get in a state where we can reset the SCSI bus */
- ncr_halt (host);
- ncr_scsi_reset (host);
- hostdata->soft_reset(host);
-
- disable (host);
- local_irq_restore(flags);
- return 0;
-}
-
-/*
- * Function : void ncr_scsi_reset (struct Scsi_Host *host)
- *
- * Purpose : reset the SCSI bus.
- */
-
-static void
-ncr_scsi_reset (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- unsigned long flags;
- NCR53c7x0_local_setup(host);
- local_irq_save(flags);
- NCR53c7x0_write8(SCNTL1_REG, SCNTL1_RST);
- udelay(25); /* Minimum amount of time to assert RST */
- NCR53c7x0_write8(SCNTL1_REG, 0);
- local_irq_restore(flags);
-}
-
-/*
- * Function : void hard_reset (struct Scsi_Host *host)
- *
- */
-
-static void
-hard_reset (struct Scsi_Host *host) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned long flags;
- local_irq_save(flags);
- ncr_scsi_reset(host);
- NCR53c7x0_driver_init (host);
- if (hostdata->soft_reset)
- hostdata->soft_reset (host);
- local_irq_restore(flags);
-}
-
-
-/*
- * Function : Scsi_Cmnd *return_outstanding_commands (struct Scsi_Host *host,
- * int free, int issue)
- *
- * Purpose : return a linked list (using the SCp.buffer field as next,
- * so we don't perturb hostdata. We don't use a field of the
- * NCR53c7x0_cmd structure since we may not have allocated one
- * for the command causing the reset.) of Scsi_Cmnd structures that
- * had propagated below the Linux issue queue level. If free is set,
- * free the NCR53c7x0_cmd structures which are associated with
- * the Scsi_Cmnd structures, and clean up any internal
- * NCR lists that the commands were on. If issue is set,
- * also return commands in the issue queue.
- *
- * Returns : linked list of commands
- *
- * NOTE : the caller should insure that the NCR chip is halted
- * if the free flag is set.
- */
-
-static Scsi_Cmnd *
-return_outstanding_commands (struct Scsi_Host *host, int free, int issue) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- struct NCR53c7x0_cmd *c;
- int i;
- u32 *ncrcurrent;
- Scsi_Cmnd *list = NULL, *tmp;
- for (c = (struct NCR53c7x0_cmd *) hostdata->running_list; c;
- c = (struct NCR53c7x0_cmd *) c->next) {
- if (c->cmd->SCp.buffer) {
- printk ("scsi%d : loop detected in running list!\n", host->host_no);
- break;
- } else {
- printk ("Duh? Bad things happening in the NCR driver\n");
- break;
- }
-
- c->cmd->SCp.buffer = (struct scatterlist *) list;
- list = c->cmd;
- if (free) {
- c->next = hostdata->free;
- hostdata->free = c;
- }
- }
-
- if (free) {
- for (i = 0, ncrcurrent = (u32 *) hostdata->schedule;
- i < host->can_queue; ++i, ncrcurrent += 2) {
- ncrcurrent[0] = hostdata->NOP_insn;
- ncrcurrent[1] = 0xdeadbeef;
- }
- hostdata->ncrcurrent = NULL;
- }
-
- if (issue) {
- for (tmp = (Scsi_Cmnd *) hostdata->issue_queue; tmp; tmp = tmp->next) {
- if (tmp->SCp.buffer) {
- printk ("scsi%d : loop detected in issue queue!\n",
- host->host_no);
- break;
- }
- tmp->SCp.buffer = (struct scatterlist *) list;
- list = tmp;
- }
- if (free)
- hostdata->issue_queue = NULL;
-
- }
- return list;
-}
-
-/*
- * Function : static int disable (struct Scsi_Host *host)
- *
- * Purpose : disables the given NCR host, causing all commands
- * to return a driver error. Call this so we can unload the
- * module during development and try again. Eventually,
- * we should be able to find clean workarounds for these
- * problems.
- *
- * Inputs : host - hostadapter to twiddle
- *
- * Returns : 0 on success.
- */
-
-static int
-disable (struct Scsi_Host *host) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- unsigned long flags;
- Scsi_Cmnd *nuke_list, *tmp;
- local_irq_save(flags);
- if (hostdata->state != STATE_HALTED)
- ncr_halt (host);
- nuke_list = return_outstanding_commands (host, 1 /* free */, 1 /* issue */);
- hard_reset (host);
- hostdata->state = STATE_DISABLED;
- local_irq_restore(flags);
- printk ("scsi%d : nuking commands\n", host->host_no);
- for (; nuke_list; nuke_list = tmp) {
- tmp = (Scsi_Cmnd *) nuke_list->SCp.buffer;
- nuke_list->result = DID_ERROR << 16;
- nuke_list->scsi_done(nuke_list);
- }
- printk ("scsi%d : done. \n", host->host_no);
- printk (KERN_ALERT "scsi%d : disabled. Unload and reload\n",
- host->host_no);
- return 0;
-}
-
-/*
- * Function : static int ncr_halt (struct Scsi_Host *host)
- *
- * Purpose : halts the SCSI SCRIPTS(tm) processor on the NCR chip
- *
- * Inputs : host - SCSI chip to halt
- *
- * Returns : 0 on success
- */
-
-static int
-ncr_halt (struct Scsi_Host *host) {
- NCR53c7x0_local_declare();
- unsigned long flags;
- unsigned char istat, tmp;
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- int stage;
- NCR53c7x0_local_setup(host);
-
- local_irq_save(flags);
- /* Stage 0 : eat all interrupts
- Stage 1 : set ABORT
- Stage 2 : eat all but abort interrupts
- Stage 3 : eat all interrupts
- */
- for (stage = 0;;) {
- if (stage == 1) {
- NCR53c7x0_write8(hostdata->istat, ISTAT_ABRT);
- ++stage;
- }
- istat = NCR53c7x0_read8 (hostdata->istat);
- if (istat & ISTAT_SIP) {
- tmp = NCR53c7x0_read8(SSTAT0_REG);
- } else if (istat & ISTAT_DIP) {
- tmp = NCR53c7x0_read8(DSTAT_REG);
- if (stage == 2) {
- if (tmp & DSTAT_ABRT) {
- NCR53c7x0_write8(hostdata->istat, 0);
- ++stage;
- } else {
- printk(KERN_ALERT "scsi%d : could not halt NCR chip\n",
- host->host_no);
- disable (host);
- }
- }
- }
- if (!(istat & (ISTAT_SIP|ISTAT_DIP))) {
- if (stage == 0)
- ++stage;
- else if (stage == 3)
- break;
- }
- }
- hostdata->state = STATE_HALTED;
- local_irq_restore(flags);
-#if 0
- print_lots (host);
-#endif
- return 0;
-}
-
-/*
- * Function: event_name (int event)
- *
- * Purpose: map event enum into user-readable strings.
- */
-
-static const char *
-event_name (int event) {
- switch (event) {
- case EVENT_NONE: return "none";
- case EVENT_ISSUE_QUEUE: return "to issue queue";
- case EVENT_START_QUEUE: return "to start queue";
- case EVENT_SELECT: return "selected";
- case EVENT_DISCONNECT: return "disconnected";
- case EVENT_RESELECT: return "reselected";
- case EVENT_COMPLETE: return "completed";
- case EVENT_IDLE: return "idle";
- case EVENT_SELECT_FAILED: return "select failed";
- case EVENT_BEFORE_SELECT: return "before select";
- case EVENT_RESELECT_FAILED: return "reselect failed";
- default: return "unknown";
- }
-}
-
-/*
- * Function : void dump_events (struct Scsi_Host *host, count)
- *
- * Purpose : print last count events which have occurred.
- */
-static void
-dump_events (struct Scsi_Host *host, int count) {
- struct NCR53c7x0_hostdata *hostdata = (struct NCR53c7x0_hostdata *)
- host->hostdata[0];
- struct NCR53c7x0_event event;
- int i;
- unsigned long flags;
- if (hostdata->events) {
- if (count > hostdata->event_size)
- count = hostdata->event_size;
- for (i = hostdata->event_index; count > 0;
- i = (i ? i - 1 : hostdata->event_size -1), --count) {
-/*
- * By copying the event we're currently examining with interrupts
- * disabled, we can do multiple printk(), etc. operations and
- * still be guaranteed that they're happening on the same
- * event structure.
- */
- local_irq_save(flags);
-#if 0
- event = hostdata->events[i];
-#else
- memcpy ((void *) &event, (void *) &(hostdata->events[i]),
- sizeof(event));
-#endif
-
- local_irq_restore(flags);
- printk ("scsi%d : %s event %d at %ld secs %ld usecs target %d lun %d\n",
- host->host_no, event_name (event.event), count,
- (long) event.time.tv_sec, (long) event.time.tv_usec,
- event.target, event.lun);
- if (event.dsa)
- printk (" event for dsa 0x%lx (virt 0x%p)\n",
- virt_to_bus(event.dsa), event.dsa);
- if (event.pid != -1) {
- printk (" event for pid %ld ", event.pid);
- __scsi_print_command (event.cmnd);
- }
- }
- }
-}
-
-/*
- * Function: check_address
- *
- * Purpose: Check to see if a possibly corrupt pointer will fault the
- * kernel.
- *
- * Inputs: addr - address; size - size of area
- *
- * Returns: 0 if area is OK, -1 on error.
- *
- * NOTES: should be implemented in terms of vverify on kernels
- * that have it.
- */
-
-static int
-check_address (unsigned long addr, int size) {
- return (virt_to_phys((void *)addr) < PAGE_SIZE || virt_to_phys((void *)(addr + size)) > virt_to_phys(high_memory) ? -1 : 0);
-}
-
-#ifdef MODULE
-int
-NCR53c7x0_release(struct Scsi_Host *host) {
- struct NCR53c7x0_hostdata *hostdata =
- (struct NCR53c7x0_hostdata *) host->hostdata[0];
- struct NCR53c7x0_cmd *cmd, *tmp;
- shutdown (host);
- if (host->irq != SCSI_IRQ_NONE)
- {
- int irq_count;
- struct Scsi_Host *tmp;
- for (irq_count = 0, tmp = first_host; tmp; tmp = tmp->next)
- if (tmp->hostt == the_template && tmp->irq == host->irq)
- ++irq_count;
- if (irq_count == 1)
- free_irq(host->irq, NULL);
- }
- if (host->dma_channel != DMA_NONE)
- free_dma(host->dma_channel);
- if (host->io_port)
- release_region(host->io_port, host->n_io_port);
-
- for (cmd = (struct NCR53c7x0_cmd *) hostdata->free; cmd; cmd = tmp,
- --hostdata->num_cmds) {
- tmp = (struct NCR53c7x0_cmd *) cmd->next;
- /*
- * If we're going to loop, try to stop it to get a more accurate
- * count of the leaked commands.
- */
- cmd->next = NULL;
- if (cmd->free)
- cmd->free ((void *) cmd->real, cmd->size);
- }
- if (hostdata->num_cmds)
- printk ("scsi%d : leaked %d NCR53c7x0_cmd structures\n",
- host->host_no, hostdata->num_cmds);
-
- vfree(hostdata->events);
-
- /* XXX This assumes default cache mode to be IOMAP_FULL_CACHING, which
- * XXX may be invalid (CONFIG_060_WRITETHROUGH)
- */
- kernel_set_cachemode((void *)hostdata, 8192, IOMAP_FULL_CACHING);
- free_pages ((u32)hostdata, 1);
- return 1;
-}
-#endif /* def MODULE */