diff options
Diffstat (limited to 'drivers/scsi/ata_piix.c')
| -rw-r--r-- | drivers/scsi/ata_piix.c | 1040 |
1 files changed, 0 insertions, 1040 deletions
diff --git a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c deleted file mode 100644 index a9bb3cb7e89..00000000000 --- a/drivers/scsi/ata_piix.c +++ /dev/null @@ -1,1040 +0,0 @@ -/* - * ata_piix.c - Intel PATA/SATA controllers - * - * Maintained by: Jeff Garzik <jgarzik@pobox.com> - * Please ALWAYS copy linux-ide@vger.kernel.org - * on emails. - * - * - * Copyright 2003-2005 Red Hat Inc - * Copyright 2003-2005 Jeff Garzik - * - * - * Copyright header from piix.c: - * - * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer - * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> - * Copyright (C) 2003 Red Hat Inc <alan@redhat.com> - * - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2, or (at your option) - * any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; see the file COPYING. If not, write to - * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. - * - * - * libata documentation is available via 'make {ps|pdf}docs', - * as Documentation/DocBook/libata.* - * - * Hardware documentation available at http://developer.intel.com/ - * - * Documentation - * Publically available from Intel web site. Errata documentation - * is also publically available. As an aide to anyone hacking on this - * driver the list of errata that are relevant is below.going back to - * PIIX4. Older device documentation is now a bit tricky to find. - * - * The chipsets all follow very much the same design. The orginal Triton - * series chipsets do _not_ support independant device timings, but this - * is fixed in Triton II. With the odd mobile exception the chips then - * change little except in gaining more modes until SATA arrives. This - * driver supports only the chips with independant timing (that is those - * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix - * for the early chip drivers. - * - * Errata of note: - * - * Unfixable - * PIIX4 errata #9 - Only on ultra obscure hw - * ICH3 errata #13 - Not observed to affect real hw - * by Intel - * - * Things we must deal with - * PIIX4 errata #10 - BM IDE hang with non UDMA - * (must stop/start dma to recover) - * 440MX errata #15 - As PIIX4 errata #10 - * PIIX4 errata #15 - Must not read control registers - * during a PIO transfer - * 440MX errata #13 - As PIIX4 errata #15 - * ICH2 errata #21 - DMA mode 0 doesn't work right - * ICH0/1 errata #55 - As ICH2 errata #21 - * ICH2 spec c #9 - Extra operations needed to handle - * drive hotswap [NOT YET SUPPORTED] - * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary - * and must be dword aligned - * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3 - * - * Should have been BIOS fixed: - * 450NX: errata #19 - DMA hangs on old 450NX - * 450NX: errata #20 - DMA hangs on old 450NX - * 450NX: errata #25 - Corruption with DMA on old 450NX - * ICH3 errata #15 - IDE deadlock under high load - * (BIOS must set dev 31 fn 0 bit 23) - * ICH3 errata #18 - Don't use native mode - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/pci.h> -#include <linux/init.h> -#include <linux/blkdev.h> -#include <linux/delay.h> -#include <linux/device.h> -#include <scsi/scsi_host.h> -#include <linux/libata.h> - -#define DRV_NAME "ata_piix" -#define DRV_VERSION "2.00" - -enum { - PIIX_IOCFG = 0x54, /* IDE I/O configuration register */ - ICH5_PMR = 0x90, /* port mapping register */ - ICH5_PCS = 0x92, /* port control and status */ - PIIX_SCC = 0x0A, /* sub-class code register */ - - PIIX_FLAG_IGNORE_PCS = (1 << 25), /* ignore PCS present bits */ - PIIX_FLAG_SCR = (1 << 26), /* SCR available */ - PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */ - PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */ - - /* combined mode. if set, PATA is channel 0. - * if clear, PATA is channel 1. - */ - PIIX_PORT_ENABLED = (1 << 0), - PIIX_PORT_PRESENT = (1 << 4), - - PIIX_80C_PRI = (1 << 5) | (1 << 4), - PIIX_80C_SEC = (1 << 7) | (1 << 6), - - /* controller IDs */ - piix4_pata = 0, - ich5_pata = 1, - ich5_sata = 2, - esb_sata = 3, - ich6_sata = 4, - ich6_sata_ahci = 5, - ich6m_sata_ahci = 6, - ich7m_sata_ahci = 7, - ich8_sata_ahci = 8, - - /* constants for mapping table */ - P0 = 0, /* port 0 */ - P1 = 1, /* port 1 */ - P2 = 2, /* port 2 */ - P3 = 3, /* port 3 */ - IDE = -1, /* IDE */ - NA = -2, /* not avaliable */ - RV = -3, /* reserved */ - - PIIX_AHCI_DEVICE = 6, -}; - -struct piix_map_db { - const u32 mask; - const u16 port_enable; - const int present_shift; - const int map[][4]; -}; - -struct piix_host_priv { - const int *map; - const struct piix_map_db *map_db; -}; - -static int piix_init_one (struct pci_dev *pdev, - const struct pci_device_id *ent); -static void piix_host_stop(struct ata_host_set *host_set); -static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev); -static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev); -static void piix_pata_error_handler(struct ata_port *ap); -static void piix_sata_error_handler(struct ata_port *ap); - -static unsigned int in_module_init = 1; - -static const struct pci_device_id piix_pci_tbl[] = { -#ifdef ATA_ENABLE_PATA - { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix4_pata }, - { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata }, - { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata }, - { 0x8086, 0x27df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata }, -#endif - - /* NOTE: The following PCI ids must be kept in sync with the - * list in drivers/pci/quirks.c. - */ - - /* 82801EB (ICH5) */ - { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata }, - /* 82801EB (ICH5) */ - { 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata }, - /* 6300ESB (ICH5 variant with broken PCS present bits) */ - { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata }, - /* 6300ESB pretending RAID */ - { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata }, - /* 82801FB/FW (ICH6/ICH6W) */ - { 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata }, - /* 82801FR/FRW (ICH6R/ICH6RW) */ - { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci }, - /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */ - { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci }, - /* 82801GB/GR/GH (ICH7, identical to ICH6) */ - { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci }, - /* 2801GBM/GHM (ICH7M, identical to ICH6M) */ - { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich7m_sata_ahci }, - /* Enterprise Southbridge 2 (where's the datasheet?) */ - { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci }, - /* SATA Controller 1 IDE (ICH8, no datasheet yet) */ - { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci }, - /* SATA Controller 2 IDE (ICH8, ditto) */ - { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci }, - /* Mobile SATA Controller IDE (ICH8M, ditto) */ - { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci }, - - { } /* terminate list */ -}; - -static struct pci_driver piix_pci_driver = { - .name = DRV_NAME, - .id_table = piix_pci_tbl, - .probe = piix_init_one, - .remove = ata_pci_remove_one, - .suspend = ata_pci_device_suspend, - .resume = ata_pci_device_resume, -}; - -static struct scsi_host_template piix_sht = { - .module = THIS_MODULE, - .name = DRV_NAME, - .ioctl = ata_scsi_ioctl, - .queuecommand = ata_scsi_queuecmd, - .can_queue = ATA_DEF_QUEUE, - .this_id = ATA_SHT_THIS_ID, - .sg_tablesize = LIBATA_MAX_PRD, - .cmd_per_lun = ATA_SHT_CMD_PER_LUN, - .emulated = ATA_SHT_EMULATED, - .use_clustering = ATA_SHT_USE_CLUSTERING, - .proc_name = DRV_NAME, - .dma_boundary = ATA_DMA_BOUNDARY, - .slave_configure = ata_scsi_slave_config, - .slave_destroy = ata_scsi_slave_destroy, - .bios_param = ata_std_bios_param, - .resume = ata_scsi_device_resume, - .suspend = ata_scsi_device_suspend, -}; - -static const struct ata_port_operations piix_pata_ops = { - .port_disable = ata_port_disable, - .set_piomode = piix_set_piomode, - .set_dmamode = piix_set_dmamode, - .mode_filter = ata_pci_default_filter, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, - - .bmdma_setup = ata_bmdma_setup, - .bmdma_start = ata_bmdma_start, - .bmdma_stop = ata_bmdma_stop, - .bmdma_status = ata_bmdma_status, - .qc_prep = ata_qc_prep, - .qc_issue = ata_qc_issue_prot, - .data_xfer = ata_pio_data_xfer, - - .freeze = ata_bmdma_freeze, - .thaw = ata_bmdma_thaw, - .error_handler = piix_pata_error_handler, - .post_internal_cmd = ata_bmdma_post_internal_cmd, - - .irq_handler = ata_interrupt, - .irq_clear = ata_bmdma_irq_clear, - - .port_start = ata_port_start, - .port_stop = ata_port_stop, - .host_stop = piix_host_stop, -}; - -static const struct ata_port_operations piix_sata_ops = { - .port_disable = ata_port_disable, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, - - .bmdma_setup = ata_bmdma_setup, - .bmdma_start = ata_bmdma_start, - .bmdma_stop = ata_bmdma_stop, - .bmdma_status = ata_bmdma_status, - .qc_prep = ata_qc_prep, - .qc_issue = ata_qc_issue_prot, - .data_xfer = ata_pio_data_xfer, - - .freeze = ata_bmdma_freeze, - .thaw = ata_bmdma_thaw, - .error_handler = piix_sata_error_handler, - .post_internal_cmd = ata_bmdma_post_internal_cmd, - - .irq_handler = ata_interrupt, - .irq_clear = ata_bmdma_irq_clear, - - .port_start = ata_port_start, - .port_stop = ata_port_stop, - .host_stop = piix_host_stop, -}; - -static const struct piix_map_db ich5_map_db = { - .mask = 0x7, - .port_enable = 0x3, - .present_shift = 4, - .map = { - /* PM PS SM SS MAP */ - { P0, NA, P1, NA }, /* 000b */ - { P1, NA, P0, NA }, /* 001b */ - { RV, RV, RV, RV }, - { RV, RV, RV, RV }, - { P0, P1, IDE, IDE }, /* 100b */ - { P1, P0, IDE, IDE }, /* 101b */ - { IDE, IDE, P0, P1 }, /* 110b */ - { IDE, IDE, P1, P0 }, /* 111b */ - }, -}; - -static const struct piix_map_db ich6_map_db = { - .mask = 0x3, - .port_enable = 0xf, - .present_shift = 4, - .map = { - /* PM PS SM SS MAP */ - { P0, P2, P1, P3 }, /* 00b */ - { IDE, IDE, P1, P3 }, /* 01b */ - { P0, P2, IDE, IDE }, /* 10b */ - { RV, RV, RV, RV }, - }, -}; - -static const struct piix_map_db ich6m_map_db = { - .mask = 0x3, - .port_enable = 0x5, - .present_shift = 4, - .map = { - /* PM PS SM SS MAP */ - { P0, P2, RV, RV }, /* 00b */ - { RV, RV, RV, RV }, - { P0, P2, IDE, IDE }, /* 10b */ - { RV, RV, RV, RV }, - }, -}; - -static const struct piix_map_db ich7m_map_db = { - .mask = 0x3, - .port_enable = 0x5, - .present_shift = 4, - - /* Map 01b isn't specified in the doc but some notebooks use - * it anyway. ATM, the only case spotted carries subsystem ID - * 1025:0107. This is the only difference from ich6m. - */ - .map = { - /* PM PS SM SS MAP */ - { P0, P2, RV, RV }, /* 00b */ - { IDE, IDE, P1, P3 }, /* 01b */ - { P0, P2, IDE, IDE }, /* 10b */ - { RV, RV, RV, RV }, - }, -}; - -static const struct piix_map_db ich8_map_db = { - .mask = 0x3, - .port_enable = 0x3, - .present_shift = 8, - .map = { - /* PM PS SM SS MAP */ - { P0, NA, P1, NA }, /* 00b (hardwired) */ - { RV, RV, RV, RV }, - { RV, RV, RV, RV }, /* 10b (never) */ - { RV, RV, RV, RV }, - }, -}; - -static const struct piix_map_db *piix_map_db_table[] = { - [ich5_sata] = &ich5_map_db, - [esb_sata] = &ich5_map_db, - [ich6_sata] = &ich6_map_db, - [ich6_sata_ahci] = &ich6_map_db, - [ich6m_sata_ahci] = &ich6m_map_db, - [ich7m_sata_ahci] = &ich7m_map_db, - [ich8_sata_ahci] = &ich8_map_db, -}; - -static struct ata_port_info piix_port_info[] = { - /* piix4_pata */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SLAVE_POSS, - .pio_mask = 0x1f, /* pio0-4 */ -#if 0 - .mwdma_mask = 0x06, /* mwdma1-2 */ -#else - .mwdma_mask = 0x00, /* mwdma broken */ -#endif - .udma_mask = ATA_UDMA_MASK_40C, - .port_ops = &piix_pata_ops, - }, - - /* ich5_pata */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR, - .pio_mask = 0x1f, /* pio0-4 */ -#if 0 - .mwdma_mask = 0x06, /* mwdma1-2 */ -#else - .mwdma_mask = 0x00, /* mwdma broken */ -#endif - .udma_mask = 0x3f, /* udma0-5 */ - .port_ops = &piix_pata_ops, - }, - - /* ich5_sata */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR | - PIIX_FLAG_IGNORE_PCS, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, - - /* i6300esb_sata */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | - PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, - - /* ich6_sata */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | - PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, - - /* ich6_sata_ahci */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | - PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | - PIIX_FLAG_AHCI, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, - - /* ich6m_sata_ahci */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | - PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | - PIIX_FLAG_AHCI, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, - - /* ich7m_sata_ahci */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | - PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | - PIIX_FLAG_AHCI, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, - - /* ich8_sata_ahci */ - { - .sht = &piix_sht, - .host_flags = ATA_FLAG_SATA | - PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | - PIIX_FLAG_AHCI, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 */ - .port_ops = &piix_sata_ops, - }, -}; - -static struct pci_bits piix_enable_bits[] = { - { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ - { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ -}; - -MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik"); -MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers"); -MODULE_LICENSE("GPL"); -MODULE_DEVICE_TABLE(pci, piix_pci_tbl); -MODULE_VERSION(DRV_VERSION); - -static int force_pcs = 0; -module_param(force_pcs, int, 0444); -MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around " - "device mis-detection (0=default, 1=ignore PCS, 2=honor PCS)"); - -/** - * piix_pata_cbl_detect - Probe host controller cable detect info - * @ap: Port for which cable detect info is desired - * - * Read 80c cable indicator from ATA PCI device's PCI config - * register. This register is normally set by firmware (BIOS). - * - * LOCKING: - * None (inherited from caller). - */ -static void piix_pata_cbl_detect(struct ata_port *ap) -{ - struct pci_dev *pdev = to_pci_dev(ap->host_set->dev); - u8 tmp, mask; - - /* no 80c support in host controller? */ - if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0) - goto cbl40; - - /* check BIOS cable detect results */ - mask = ap->hard_port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC; - pci_read_config_byte(pdev, PIIX_IOCFG, &tmp); - if ((tmp & mask) == 0) - goto cbl40; - - ap->cbl = ATA_CBL_PATA80; - return; - -cbl40: - ap->cbl = ATA_CBL_PATA40; - ap->udma_mask &= ATA_UDMA_MASK_40C; -} - -/** - * piix_pata_prereset - prereset for PATA host controller - * @ap: Target port - * - * Prereset including cable detection. - * - * LOCKING: - * None (inherited from caller). - */ -static int piix_pata_prereset(struct ata_port *ap) -{ - struct pci_dev *pdev = to_pci_dev(ap->host_set->dev); - - if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) { - ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n"); - ap->eh_context.i.action &= ~ATA_EH_RESET_MASK; - return 0; - } - - piix_pata_cbl_detect(ap); - - return ata_std_prereset(ap); -} - -static void piix_pata_error_handler(struct ata_port *ap) -{ - ata_bmdma_drive_eh(ap, piix_pata_prereset, ata_std_softreset, NULL, - ata_std_postreset); -} - -/** - * piix_sata_present_mask - determine present mask for SATA host controller - * @ap: Target port - * - * Reads SATA PCI device's PCI config register Port Configuration - * and Status (PCS) to determine port and device availability. - * - * LOCKING: - * None (inherited from caller). - * - * RETURNS: - * determined present_mask - */ -static unsigned int piix_sata_present_mask(struct ata_port *ap) -{ - struct pci_dev *pdev = to_pci_dev(ap->host_set->dev); - struct piix_host_priv *hpriv = ap->host_set->private_data; - const unsigned int *map = hpriv->map; - int base = 2 * ap->hard_port_no; - unsigned int present_mask = 0; - int port, i; - u16 pcs; - - pci_read_config_word(pdev, ICH5_PCS, &pcs); - DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base); - - for (i = 0; i < 2; i++) { - port = map[base + i]; - if (port < 0) - continue; - if ((ap->flags & PIIX_FLAG_IGNORE_PCS) || - (pcs & 1 << (hpriv->map_db->present_shift + port))) - present_mask |= 1 << i; - } - - DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n", - ap->id, pcs, present_mask); - - return present_mask; -} - -/** - * piix_sata_softreset - reset SATA host port via ATA SRST - * @ap: port to reset - * @classes: resulting classes of attached devices - * - * Reset SATA host port via ATA SRST. On controllers with - * reliable PCS present bits, the bits are used to determine - * device presence. - * - * LOCKING: - * Kernel thread context (may sleep) - * - * RETURNS: - * 0 on success, -errno otherwise. - */ -static int piix_sata_softreset(struct ata_port *ap, unsigned int *classes) -{ - unsigned int present_mask; - int i, rc; - - present_mask = piix_sata_present_mask(ap); - - rc = ata_std_softreset(ap, classes); - if (rc) - return rc; - - for (i = 0; i < ATA_MAX_DEVICES; i++) { - if (!(present_mask & (1 << i))) - classes[i] = ATA_DEV_NONE; - } - - return 0; -} - -static void piix_sata_error_handler(struct ata_port *ap) -{ - ata_bmdma_drive_eh(ap, ata_std_prereset, piix_sata_softreset, NULL, - ata_std_postreset); -} - -/** - * piix_set_piomode - Initialize host controller PATA PIO timings - * @ap: Port whose timings we are configuring - * @adev: um - * - * Set PIO mode for device, in host controller PCI config space. - * - * LOCKING: - * None (inherited from caller). - */ - -static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev) -{ - unsigned int pio = adev->pio_mode - XFER_PIO_0; - struct pci_dev *dev = to_pci_dev(ap->host_set->dev); - unsigned int is_slave = (adev->devno != 0); - unsigned int master_port= ap->hard_port_no ? 0x42 : 0x40; - unsigned int slave_port = 0x44; - u16 master_data; - u8 slave_data; - - static const /* ISP RTC */ - u8 timings[][2] = { { 0, 0 }, - { 0, 0 }, - { 1, 0 }, - { 2, 1 }, - { 2, 3 }, }; - - pci_read_config_word(dev, master_port, &master_data); - if (is_slave) { - master_data |= 0x4000; - /* enable PPE, IE and TIME */ - master_data |= 0x0070; - pci_read_config_byte(dev, slave_port, &slave_data); - slave_data &= (ap->hard_port_no ? 0x0f : 0xf0); - slave_data |= - (timings[pio][0] << 2) | - (timings[pio][1] << (ap->hard_port_no ? 4 : 0)); - } else { - master_data &= 0xccf8; - /* enable PPE, IE and TIME */ - master_data |= 0x0007; - master_data |= - (timings[pio][0] << 12) | - (timings[pio][1] << 8); - } - pci_write_config_word(dev, master_port, master_data); - if (is_slave) - pci_write_config_byte(dev, slave_port, slave_data); -} - -/** - * piix_set_dmamode - Initialize host controller PATA PIO timings - * @ap: Port whose timings we are configuring - * @adev: um - * @udma: udma mode, 0 - 6 - * - * Set UDMA mode for device, in host controller PCI config space. - * - * LOCKING: - * None (inherited from caller). - */ - -static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev) -{ - unsigned int udma = adev->dma_mode; /* FIXME: MWDMA too */ - struct pci_dev *dev = to_pci_dev(ap->host_set->dev); - u8 maslave = ap->hard_port_no ? 0x42 : 0x40; - u8 speed = udma; - unsigned int drive_dn = (ap->hard_port_no ? 2 : 0) + adev->devno; - int a_speed = 3 << (drive_dn * 4); - int u_flag = 1 << drive_dn; - int v_flag = 0x01 << drive_dn; - int w_flag = 0x10 << drive_dn; - int u_speed = 0; - int sitre; - u16 reg4042, reg4a; - u8 reg48, reg54, reg55; - - pci_read_config_word(dev, maslave, ®4042); - DPRINTK("reg4042 = 0x%04x\n", reg4042); - sitre = (reg4042 & 0x4000) ? 1 : 0; - pci_read_config_byte(dev, 0x48, ®48); - pci_read_config_word(dev, 0x4a, ®4a); - pci_read_config_byte(dev, 0x54, ®54); - pci_read_config_byte(dev, 0x55, ®55); - - switch(speed) { - case XFER_UDMA_4: - case XFER_UDMA_2: u_speed = 2 << (drive_dn * 4); break; - case XFER_UDMA_6: - case XFER_UDMA_5: - case XFER_UDMA_3: - case XFER_UDMA_1: u_speed = 1 << (drive_dn * 4); break; - case XFER_UDMA_0: u_speed = 0 << (drive_dn * 4); break; - case XFER_MW_DMA_2: - case XFER_MW_DMA_1: break; - default: - BUG(); - return; - } - - if (speed >= XFER_UDMA_0) { - if (!(reg48 & u_flag)) - pci_write_config_byte(dev, 0x48, reg48 | u_flag); - if (speed == XFER_UDMA_5) { - pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag); - } else { - pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag); - } - if ((reg4a & a_speed) != u_speed) - pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed); - if (speed > XFER_UDMA_2) { - if (!(reg54 & v_flag)) - pci_write_config_byte(dev, 0x54, reg54 | v_flag); - } else - pci_write_config_byte(dev, 0x54, reg54 & ~v_flag); - } else { - if (reg48 & u_flag) - pci_write_config_byte(dev, 0x48, reg48 & ~u_flag); - if (reg4a & a_speed) - pci_write_config_word(dev, 0x4a, reg4a & ~a_speed); - if (reg54 & v_flag) - pci_write_config_byte(dev, 0x54, reg54 & ~v_flag); - if (reg55 & w_flag) - pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag); - } -} - -#define AHCI_PCI_BAR 5 -#define AHCI_GLOBAL_CTL 0x04 -#define AHCI_ENABLE (1 << 31) -static int piix_disable_ahci(struct pci_dev *pdev) -{ - void __iomem *mmio; - u32 tmp; - int rc = 0; - - /* BUG: pci_enable_device has not yet been called. This - * works because this device is usually set up by BIOS. - */ - - if (!pci_resource_start(pdev, AHCI_PCI_BAR) || - !pci_resource_len(pdev, AHCI_PCI_BAR)) - return 0; - - mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64); - if (!mmio) - return -ENOMEM; - - tmp = readl(mmio + AHCI_GLOBAL_CTL); - if (tmp & AHCI_ENABLE) { - tmp &= ~AHCI_ENABLE; - writel(tmp, mmio + AHCI_GLOBAL_CTL); - - tmp = readl(mmio + AHCI_GLOBAL_CTL); - if (tmp & AHCI_ENABLE) - rc = -EIO; - } - - pci_iounmap(pdev, mmio); - return rc; -} - -/** - * piix_check_450nx_errata - Check for problem 450NX setup - * @ata_dev: the PCI device to check - * - * Check for the present of 450NX errata #19 and errata #25. If - * they are found return an error code so we can turn off DMA - */ - -static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev) -{ - struct pci_dev *pdev = NULL; - u16 cfg; - u8 rev; - int no_piix_dma = 0; - - while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL) - { - /* Look for 450NX PXB. Check for problem configurations - A PCI quirk checks bit 6 already */ - pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); - pci_read_config_word(pdev, 0x41, &cfg); - /* Only on the original revision: IDE DMA can hang */ - if (rev == 0x00) - no_piix_dma = 1; - /* On all revisions below 5 PXB bus lock must be disabled for IDE */ - else if (cfg & (1<<14) && rev < 5) - no_piix_dma = 2; - } - if (no_piix_dma) - dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n"); - if (no_piix_dma == 2) - dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n"); - return no_piix_dma; -} - -static void __devinit piix_init_pcs(struct pci_dev *pdev, - struct ata_port_info *pinfo, - const struct piix_map_db *map_db) -{ - u16 pcs, new_pcs; - - pci_read_config_word(pdev, ICH5_PCS, &pcs); - - new_pcs = pcs | map_db->port_enable; - - if (new_pcs != pcs) { - DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs); - pci_write_config_word(pdev, ICH5_PCS, new_pcs); - msleep(150); - } - - if (force_pcs == 1) { - dev_printk(KERN_INFO, &pdev->dev, - "force ignoring PCS (0x%x)\n", new_pcs); - pinfo[0].host_flags |= PIIX_FLAG_IGNORE_PCS; - pinfo[1].host_flags |= PIIX_FLAG_IGNORE_PCS; - } else if (force_pcs == 2) { - dev_printk(KERN_INFO, &pdev->dev, - "force honoring PCS (0x%x)\n", new_pcs); - pinfo[0].host_flags &= ~PIIX_FLAG_IGNORE_PCS; - pinfo[1].host_flags &= ~PIIX_FLAG_IGNORE_PCS; - } -} - -static void __devinit piix_init_sata_map(struct pci_dev *pdev, - struct ata_port_info *pinfo, - const struct piix_map_db *map_db) -{ - struct piix_host_priv *hpriv = pinfo[0].private_data; - const unsigned int *map; - int i, invalid_map = 0; - u8 map_value; - - pci_read_config_byte(pdev, ICH5_PMR, &map_value); - - map = map_db->map[map_value & map_db->mask]; - - dev_printk(KERN_INFO, &pdev->dev, "MAP ["); - for (i = 0; i < 4; i++) { - switch (map[i]) { - case RV: - invalid_map = 1; - printk(" XX"); - break; - - case NA: - printk(" --"); - break; - - case IDE: - WARN_ON((i & 1) || map[i + 1] != IDE); - pinfo[i / 2] = piix_port_info[ich5_pata]; - pinfo[i / 2].private_data = hpriv; - i++; - printk(" IDE IDE"); - break; - - default: - printk(" P%d", map[i]); - if (i & 1) - pinfo[i / 2].host_flags |= ATA_FLAG_SLAVE_POSS; - break; - } - } - printk(" ]\n"); - - if (invalid_map) - dev_printk(KERN_ERR, &pdev->dev, - "invalid MAP value %u\n", map_value); - - hpriv->map = map; - hpriv->map_db = map_db; -} - -/** - * piix_init_one - Register PIIX ATA PCI device with kernel services - * @pdev: PCI device to register - * @ent: Entry in piix_pci_tbl matching with @pdev - * - * Called from kernel PCI layer. We probe for combined mode (sigh), - * and then hand over control to libata, for it to do the rest. - * - * LOCKING: - * Inherited from PCI layer (may sleep). - * - * RETURNS: - * Zero on success, or -ERRNO value. - */ - -static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) -{ - static int printed_version; - struct ata_port_info port_info[2]; - struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] }; - struct piix_host_priv *hpriv; - unsigned long host_flags; - - if (!printed_version++) - dev_printk(KERN_DEBUG, &pdev->dev, - "version " DRV_VERSION "\n"); - - /* no hotplugging support (FIXME) */ - if (!in_module_init) - return -ENODEV; - - hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL); - if (!hpriv) - return -ENOMEM; - - port_info[0] = piix_port_info[ent->driver_data]; - port_info[1] = piix_port_info[ent->driver_data]; - port_info[0].private_data = hpriv; - port_info[1].private_data = hpriv; - - host_flags = port_info[0].host_flags; - - if (host_flags & PIIX_FLAG_AHCI) { - u8 tmp; - pci_read_config_byte(pdev, PIIX_SCC, &tmp); - if (tmp == PIIX_AHCI_DEVICE) { - int rc = piix_disable_ahci(pdev); - if (rc) - return rc; - } - } - - /* Initialize SATA map */ - if (host_flags & ATA_FLAG_SATA) { - piix_init_sata_map(pdev, port_info, - piix_map_db_table[ent->driver_data]); - piix_init_pcs(pdev, port_info, - piix_map_db_table[ent->driver_data]); - } - - /* On ICH5, some BIOSen disable the interrupt using the - * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3. - * On ICH6, this bit has the same effect, but only when - * MSI is disabled (and it is disabled, as we don't use - * message-signalled interrupts currently). - */ - if (host_flags & PIIX_FLAG_CHECKINTR) - pci_intx(pdev, 1); - - if (piix_check_450nx_errata(pdev)) { - /* This writes into the master table but it does not - really matter for this errata as we will apply it to - all the PIIX devices on the board */ - port_info[0].mwdma_mask = 0; - port_info[0].udma_mask = 0; - port_info[1].mwdma_mask = 0; - port_info[1].udma_mask = 0; - } - return ata_pci_init_one(pdev, ppinfo, 2); -} - -static void piix_host_stop(struct ata_host_set *host_set) -{ - if (host_set->next == NULL) - kfree(host_set->private_data); - ata_host_stop(host_set); -} - -static int __init piix_init(void) -{ - int rc; - - DPRINTK("pci_module_init\n"); - rc = pci_module_init(&piix_pci_driver); - if (rc) - return rc; - - in_module_init = 0; - - DPRINTK("done\n"); - return 0; -} - -static void __exit piix_exit(void) -{ - pci_unregister_driver(&piix_pci_driver); -} - -module_init(piix_init); -module_exit(piix_exit); - |