diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/8250.c | 74 | ||||
| -rw-r--r-- | drivers/serial/8250_au1x00.c | 5 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart.h | 58 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_core.c | 307 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_cpm1.c | 56 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_cpm2.c | 16 | ||||
| -rw-r--r-- | drivers/serial/imx.c | 40 | ||||
| -rw-r--r-- | drivers/serial/serial_core.c | 114 |
8 files changed, 440 insertions, 230 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index 674b15c78f6..bbf78aaf9e0 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -362,6 +362,40 @@ serial_out(struct uart_8250_port *up, int offset, int value) #define serial_inp(up, offset) serial_in(up, offset) #define serial_outp(up, offset, value) serial_out(up, offset, value) +/* Uart divisor latch read */ +static inline int _serial_dl_read(struct uart_8250_port *up) +{ + return serial_inp(up, UART_DLL) | serial_inp(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static inline void _serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_outp(up, UART_DLL, value & 0xff); + serial_outp(up, UART_DLM, value >> 8 & 0xff); +} + +#ifdef CONFIG_SERIAL_8250_AU1X00 +/* Au1x00 haven't got a standard divisor latch */ +static int serial_dl_read(struct uart_8250_port *up) +{ + if (up->port.iotype == UPIO_AU) + return __raw_readl(up->port.membase + 0x28); + else + return _serial_dl_read(up); +} + +static void serial_dl_write(struct uart_8250_port *up, int value) +{ + if (up->port.iotype == UPIO_AU) + __raw_writel(value, up->port.membase + 0x28); + else + _serial_dl_write(up, value); +} +#else +#define serial_dl_read(up) _serial_dl_read(up) +#define serial_dl_write(up, value) _serial_dl_write(up, value) +#endif /* * For the 16C950 @@ -494,7 +528,8 @@ static void disable_rsa(struct uart_8250_port *up) */ static int size_fifo(struct uart_8250_port *up) { - unsigned char old_fcr, old_mcr, old_dll, old_dlm, old_lcr; + unsigned char old_fcr, old_mcr, old_lcr; + unsigned short old_dl; int count; old_lcr = serial_inp(up, UART_LCR); @@ -505,10 +540,8 @@ static int size_fifo(struct uart_8250_port *up) UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); serial_outp(up, UART_MCR, UART_MCR_LOOP); serial_outp(up, UART_LCR, UART_LCR_DLAB); - old_dll = serial_inp(up, UART_DLL); - old_dlm = serial_inp(up, UART_DLM); - serial_outp(up, UART_DLL, 0x01); - serial_outp(up, UART_DLM, 0x00); + old_dl = serial_dl_read(up); + serial_dl_write(up, 0x0001); serial_outp(up, UART_LCR, 0x03); for (count = 0; count < 256; count++) serial_outp(up, UART_TX, count); @@ -519,8 +552,7 @@ static int size_fifo(struct uart_8250_port *up) serial_outp(up, UART_FCR, old_fcr); serial_outp(up, UART_MCR, old_mcr); serial_outp(up, UART_LCR, UART_LCR_DLAB); - serial_outp(up, UART_DLL, old_dll); - serial_outp(up, UART_DLM, old_dlm); + serial_dl_write(up, old_dl); serial_outp(up, UART_LCR, old_lcr); return count; @@ -750,8 +782,7 @@ static void autoconfig_16550a(struct uart_8250_port *up) serial_outp(up, UART_LCR, 0xE0); - quot = serial_inp(up, UART_DLM) << 8; - quot += serial_inp(up, UART_DLL); + quot = serial_dl_read(up); quot <<= 3; status1 = serial_in(up, 0x04); /* EXCR1 */ @@ -759,8 +790,7 @@ static void autoconfig_16550a(struct uart_8250_port *up) status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */ serial_outp(up, 0x04, status1); - serial_outp(up, UART_DLL, quot & 0xff); - serial_outp(up, UART_DLM, quot >> 8); + serial_dl_write(up, quot); serial_outp(up, UART_LCR, 0); @@ -1862,8 +1892,7 @@ serial8250_set_termios(struct uart_port *port, struct termios *termios, serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */ } - serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */ - serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */ + serial_dl_write(up, quot); /* * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR @@ -1906,6 +1935,9 @@ static int serial8250_request_std_resource(struct uart_8250_port *up) int ret = 0; switch (up->port.iotype) { + case UPIO_AU: + size = 0x100000; + /* fall thru */ case UPIO_MEM: if (!up->port.mapbase) break; @@ -1938,6 +1970,9 @@ static void serial8250_release_std_resource(struct uart_8250_port *up) unsigned int size = 8 << up->port.regshift; switch (up->port.iotype) { + case UPIO_AU: + size = 0x100000; + /* fall thru */ case UPIO_MEM: if (!up->port.mapbase) break; @@ -2200,10 +2235,17 @@ static void serial8250_console_write(struct console *co, const char *s, unsigned int count) { struct uart_8250_port *up = &serial8250_ports[co->index]; + unsigned long flags; unsigned int ier; + int locked = 1; touch_nmi_watchdog(); + if (oops_in_progress) { + locked = spin_trylock_irqsave(&up->port.lock, flags); + } else + spin_lock_irqsave(&up->port.lock, flags); + /* * First save the IER then disable the interrupts */ @@ -2221,8 +2263,10 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) * and restore the IER */ wait_for_xmitr(up, BOTH_EMPTY); - up->ier |= UART_IER_THRI; - serial_out(up, UART_IER, ier | UART_IER_THRI); + serial_out(up, UART_IER, ier); + + if (locked) + spin_unlock_irqrestore(&up->port.lock, flags); } static int serial8250_console_setup(struct console *co, char *options) diff --git a/drivers/serial/8250_au1x00.c b/drivers/serial/8250_au1x00.c index 3d1bfd07208..58015fd14be 100644 --- a/drivers/serial/8250_au1x00.c +++ b/drivers/serial/8250_au1x00.c @@ -30,13 +30,12 @@ { \ .iobase = _base, \ .membase = (void __iomem *)_base,\ - .mapbase = _base, \ + .mapbase = CPHYSADDR(_base), \ .irq = _irq, \ .uartclk = 0, /* filled */ \ .regshift = 2, \ .iotype = UPIO_AU, \ - .flags = UPF_SKIP_TEST | \ - UPF_IOREMAP, \ + .flags = UPF_SKIP_TEST \ } static struct plat_serial8250_port au1x00_data[] = { diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h index 73c8a088c16..3b35cb77953 100644 --- a/drivers/serial/cpm_uart/cpm_uart.h +++ b/drivers/serial/cpm_uart/cpm_uart.h @@ -5,11 +5,20 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * + * 2006 (c) MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + * */ #ifndef CPM_UART_H #define CPM_UART_H #include <linux/config.h> +#include <linux/platform_device.h> +#include <linux/fs_uart_pd.h> #if defined(CONFIG_CPM2) #include "cpm_uart_cpm2.h" @@ -26,14 +35,14 @@ #define FLAG_SMC 0x00000002 #define FLAG_CONSOLE 0x00000001 -#define UART_SMC1 0 -#define UART_SMC2 1 -#define UART_SCC1 2 -#define UART_SCC2 3 -#define UART_SCC3 4 -#define UART_SCC4 5 +#define UART_SMC1 fsid_smc1_uart +#define UART_SMC2 fsid_smc2_uart +#define UART_SCC1 fsid_scc1_uart +#define UART_SCC2 fsid_scc2_uart +#define UART_SCC3 fsid_scc3_uart +#define UART_SCC4 fsid_scc4_uart -#define UART_NR 6 +#define UART_NR fs_uart_nr #define RX_NUM_FIFO 4 #define RX_BUF_SIZE 32 @@ -64,6 +73,7 @@ struct uart_cpm_port { uint dp_addr; void *mem_addr; dma_addr_t dma_addr; + u32 mem_size; /* helpers */ int baud; int bits; @@ -90,4 +100,38 @@ void scc2_lineif(struct uart_cpm_port *pinfo); void scc3_lineif(struct uart_cpm_port *pinfo); void scc4_lineif(struct uart_cpm_port *pinfo); +/* + virtual to phys transtalion +*/ +static inline unsigned long cpu2cpm_addr(void* addr, struct uart_cpm_port *pinfo) +{ + int offset; + u32 val = (u32)addr; + /* sane check */ + if (likely((val >= (u32)pinfo->mem_addr)) && + (val<((u32)pinfo->mem_addr + pinfo->mem_size))) { + offset = val - (u32)pinfo->mem_addr; + return pinfo->dma_addr+offset; + } + /* something nasty happened */ + BUG(); + return 0; +} + +static inline void *cpm2cpu_addr(unsigned long addr, struct uart_cpm_port *pinfo) +{ + int offset; + u32 val = addr; + /* sane check */ + if (likely((val >= pinfo->dma_addr) && + (val<(pinfo->dma_addr + pinfo->mem_size)))) { + offset = val - (u32)pinfo->dma_addr; + return (void*)(pinfo->mem_addr+offset); + } + /* something nasty happened */ + BUG(); + return 0; +} + + #endif /* CPM_UART_H */ diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index b7bf4c698a4..969f9490043 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -12,7 +12,8 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * (C) 2004 Intracom, S.A. - * (C) 2005 MontaVista Software, Inc. by Vitaly Bordug <vbordug@ru.mvista.com> + * (C) 2005-2006 MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -41,6 +42,7 @@ #include <linux/device.h> #include <linux/bootmem.h> #include <linux/dma-mapping.h> +#include <linux/fs_uart_pd.h> #include <asm/io.h> #include <asm/irq.h> @@ -60,7 +62,7 @@ /* Track which ports are configured as uarts */ int cpm_uart_port_map[UART_NR]; /* How many ports did we config as uarts */ -int cpm_uart_nr; +int cpm_uart_nr = 0; /**************************************************************/ @@ -71,18 +73,51 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo); /**************************************************************/ -static inline unsigned long cpu2cpm_addr(void *addr) + +/* Place-holder for board-specific stuff */ +struct platform_device* __attribute__ ((weak)) __init +early_uart_get_pdev(int index) +{ + return NULL; +} + + +static void cpm_uart_count(void) { - if ((unsigned long)addr >= CPM_ADDR) - return (unsigned long)addr; - return virt_to_bus(addr); + cpm_uart_nr = 0; +#ifdef CONFIG_SERIAL_CPM_SMC1 + cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1; +#endif +#ifdef CONFIG_SERIAL_CPM_SMC2 + cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC1 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC2 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC3 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3; +#endif +#ifdef CONFIG_SERIAL_CPM_SCC4 + cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4; +#endif } -static inline void *cpm2cpu_addr(unsigned long addr) +/* Get UART number by its id */ +static int cpm_uart_id2nr(int id) { - if (addr >= CPM_ADDR) - return (void *)addr; - return bus_to_virt(addr); + int i; + if (id < UART_NR) { + for (i=0; i<UART_NR; i++) { + if (cpm_uart_port_map[i] == id) + return i; + } + } + + /* not found or invalid argument */ + return -1; } /* @@ -258,7 +293,7 @@ static void cpm_uart_int_rx(struct uart_port *port, struct pt_regs *regs) } /* get pointer */ - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); /* loop through the buffer */ while (i-- > 0) { @@ -438,7 +473,11 @@ static void cpm_uart_shutdown(struct uart_port *port) } /* Shut them really down and reinit buffer descriptors */ - cpm_line_cr_cmd(line, CPM_CR_STOP_TX); + if (IS_SMC(pinfo)) + cpm_line_cr_cmd(line, CPM_CR_STOP_TX); + else + cpm_line_cr_cmd(line, CPM_CR_GRA_STOP_TX); + cpm_uart_initbd(pinfo); } } @@ -601,7 +640,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) /* Pick next descriptor and fill from buffer */ bdp = pinfo->tx_cur; - p = cpm2cpu_addr(bdp->cbd_bufaddr); + p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *p++ = port->x_char; bdp->cbd_datlen = 1; @@ -628,7 +667,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) while (!(bdp->cbd_sc & BD_SC_READY) && (xmit->tail != xmit->head)) { count = 0; - p = cpm2cpu_addr(bdp->cbd_bufaddr); + p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); while (count < pinfo->tx_fifosize) { *p++ = xmit->buf[xmit->tail]; xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); @@ -677,12 +716,12 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo) mem_addr = pinfo->mem_addr; bdp = pinfo->rx_cur = pinfo->rx_bd_base; for (i = 0; i < (pinfo->rx_nrfifos - 1); i++, bdp++) { - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_EMPTY | BD_SC_INTRPT; mem_addr += pinfo->rx_fifosize; } - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT; /* Set the physical address of the host memory @@ -692,12 +731,12 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo) mem_addr = pinfo->mem_addr + L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize); bdp = pinfo->tx_cur = pinfo->tx_bd_base; for (i = 0; i < (pinfo->tx_nrfifos - 1); i++, bdp++) { - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_INTRPT; mem_addr += pinfo->tx_fifosize; } - bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr); + bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo); bdp->cbd_sc = BD_SC_WRAP | BD_SC_INTRPT; } @@ -829,14 +868,6 @@ static int cpm_uart_request_port(struct uart_port *port) if (pinfo->flags & FLAG_CONSOLE) return 0; - /* - * Setup any port IO, connect any baud rate generators, - * etc. This is expected to be handled by board - * dependant code - */ - if (pinfo->set_lineif) - pinfo->set_lineif(pinfo); - if (IS_SMC(pinfo)) { pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); @@ -988,6 +1019,58 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = { }, }; +int cpm_uart_drv_get_platform_data(struct platform_device *pdev, int is_con) +{ + struct resource *r; + struct fs_uart_platform_info *pdata = pdev->dev.platform_data; + int idx = pdata->fs_no; /* It is UART_SMCx or UART_SCCx index */ + struct uart_cpm_port *pinfo; + int line; + u32 mem, pram; + + line = cpm_uart_id2nr(idx); + if(line < 0) { + printk(KERN_ERR"%s(): port %d is not registered", __FUNCTION__, idx); + return -1; + } + + pinfo = (struct uart_cpm_port *) &cpm_uart_ports[idx]; + + pinfo->brg = pdata->brg; + + if (!is_con) { + pinfo->port.line = line; + pinfo->port.flags = UPF_BOOT_AUTOCONF; + } + + if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs"))) + return -EINVAL; + mem = r->start; + + if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram"))) + return -EINVAL; + pram = r->start; + + if(idx > fsid_smc2_uart) { + pinfo->sccp = (scc_t *)mem; + pinfo->sccup = (scc_uart_t *)pram; + } else { + pinfo->smcp = (smc_t *)mem; + pinfo->smcup = (smc_uart_t *)pram; + } + pinfo->tx_nrfifos = pdata->tx_num_fifo; + pinfo->tx_fifosize = pdata->tx_buf_size; + + pinfo->rx_nrfifos = pdata->rx_num_fifo; + pinfo->rx_fifosize = pdata->rx_buf_size; + + pinfo->port.uartclk = pdata->uart_clk; + pinfo->port.mapbase = (unsigned long)mem; + pinfo->port.irq = platform_get_irq(pdev, 0); + + return 0; +} + #ifdef CONFIG_SERIAL_CPM_CONSOLE /* * Print a string to the serial port trying not to disturb @@ -1027,7 +1110,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, * If the buffer address is in the CPM DPRAM, don't * convert it. */ - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *cp = *s; @@ -1044,7 +1127,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, while ((bdp->cbd_sc & BD_SC_READY) != 0) ; - cp = cpm2cpu_addr(bdp->cbd_bufaddr); + cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo); *cp = 13; bdp->cbd_datlen = 1; @@ -1067,9 +1150,7 @@ static void cpm_uart_console_write(struct console *co, const char *s, pinfo->tx_cur = (volatile cbd_t *) bdp; } -/* - * Setup console. Be careful is called early ! - */ + static int __init cpm_uart_console_setup(struct console *co, char *options) { struct uart_port *port; @@ -1080,9 +1161,27 @@ static int __init cpm_uart_console_setup(struct console *co, char *options) int flow = 'n'; int ret; + struct fs_uart_platform_info *pdata; + struct platform_device* pdev = early_uart_get_pdev(co->index); + port = (struct uart_port *)&cpm_uart_ports[cpm_uart_port_map[co->index]]; pinfo = (struct uart_cpm_port *)port; + if (!pdev) { + pr_info("cpm_uart: console: compat mode\n"); + /* compatibility - will be cleaned up */ + cpm_uart_init_portdesc(); + + if (pinfo->set_lineif) + pinfo->set_lineif(pinfo); + } else { + pdata = pdev->dev.platform_data; + if (pdata) + if (pdata->init_ioports) + pdata->init_ioports(); + + cpm_uart_drv_get_platform_data(pdev, 1); + } pinfo->flags |= FLAG_CONSOLE; @@ -1097,14 +1196,6 @@ static int __init cpm_uart_console_setup(struct console *co, char *options) baud = 9600; } - /* - * Setup any port IO, connect any baud rate generators, - * etc. This is expected to be handled by board - * dependant code - */ - if (pinfo->set_lineif) - pinfo->set_lineif(pinfo); - if (IS_SMC(pinfo)) { pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); @@ -1143,11 +1234,8 @@ static struct console cpm_scc_uart_console = { int __init cpm_uart_console_init(void) { - int ret = cpm_uart_init_portdesc(); - - if (!ret) - register_console(&cpm_scc_uart_console); - return ret; + register_console(&cpm_scc_uart_console); + return 0; } console_initcall(cpm_uart_console_init); @@ -1165,44 +1253,129 @@ static struct uart_driver cpm_reg = { .minor = SERIAL_CPM_MINOR, .cons = CPM_UART_CONSOLE, }; - -static int __init cpm_uart_init(void) +static int cpm_uart_drv_probe(struct device *dev) { - int ret, i; - - printk(KERN_INFO "Serial: CPM driver $Revision: 0.01 $\n"); + struct platform_device *pdev = to_platform_device(dev); + struct fs_uart_platform_info *pdata; + int ret = -ENODEV; -#ifndef CONFIG_SERIAL_CPM_CONSOLE - ret = cpm_uart_init_portdesc(); - if (ret) + if(!pdev) { + printk(KERN_ERR"CPM UART: platform data missing!\n"); return ret; -#endif + } - cpm_reg.nr = cpm_uart_nr; - ret = uart_register_driver(&cpm_reg); + pdata = pdev->dev.platform_data; + pr_debug("cpm_uart_drv_probe: Adding CPM UART %d\n", cpm_uart_id2nr(pdata->fs_no)); - if (ret) + if ((ret = cpm_uart_drv_get_platform_data(pdev, 0))) return ret; - for (i = 0; i < cpm_uart_nr; i++) { - int con = cpm_uart_port_map[i]; - cpm_uart_ports[con].port.line = i; - cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF; - uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); - } + if (pdata->init_ioports) + pdata->init_ioports(); - return ret; + ret = uart_add_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port); + + return ret; } -static void __exit cpm_uart_exit(void) +static int cpm_uart_drv_remove(struct device *dev) { + struct platform_device *pdev = to_platform_device(dev); + struct fs_uart_platform_info *pdata = pdev->dev.platform_data; + + pr_debug("cpm_uart_drv_remove: Removing CPM UART %d\n", + cpm_uart_id2nr(pdata->fs_no)); + + uart_remove_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port); + return 0; +} + +static struct device_driver cpm_smc_uart_driver = { + .name = "fsl-cpm-smc:uart", + .bus = &platform_bus_type, + .probe = cpm_uart_drv_probe, + .remove = cpm_uart_drv_remove, +}; + +static struct device_driver cpm_scc_uart_driver = { + .name = "fsl-cpm-scc:uart", + .bus = &platform_bus_type, + .probe = cpm_uart_drv_probe, + .remove = cpm_uart_drv_remove, +}; + +/* + This is supposed to match uart devices on platform bus, + */ +static int match_is_uart (struct device* dev, void* data) +{ + struct platform_device* pdev = container_of(dev, struct platform_device, dev); + int ret = 0; + /* this was setfunc as uart */ + if(strstr(pdev->name,":uart")) { + ret = 1; + } + return ret; +} + + +static int cpm_uart_init(void) { + + int ret; int i; + struct device *dev; + printk(KERN_INFO "Serial: CPM driver $Revision: 0.02 $\n"); + + /* lookup the bus for uart devices */ + dev = bus_find_device(&platform_bus_type, NULL, 0, match_is_uart); + + /* There are devices on the bus - all should be OK */ + if (dev) { + cpm_uart_count(); + cpm_reg.nr = cpm_uart_nr; + + if (!(ret = uart_register_driver(&cpm_reg))) { + if ((ret = driver_register(&cpm_smc_uart_driver))) { + uart_unregister_driver(&cpm_reg); + return ret; + } + if ((ret = driver_register(&cpm_scc_uart_driver))) { + driver_unregister(&cpm_scc_uart_driver); + uart_unregister_driver(&cpm_reg); + } + } + } else { + /* No capable platform devices found - falling back to legacy mode */ + pr_info("cpm_uart: WARNING: no UART devices found on platform bus!\n"); + pr_info( + "cpm_uart: the driver will guess configuration, but this mode is no longer supported.\n"); +#ifndef CONFIG_SERIAL_CPM_CONSOLE + ret = cpm_uart_init_portdesc(); + if (ret) + return ret; +#endif + + cpm_reg.nr = cpm_uart_nr; + ret = uart_register_driver(&cpm_reg); + + if (ret) + return ret; + + for (i = 0; i < cpm_uart_nr; i++) { + int con = cpm_uart_port_map[i]; + cpm_uart_ports[con].port.line = i; + cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF; + uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); + } - for (i = 0; i < cpm_uart_nr; i++) { - int con = cpm_uart_port_map[i]; - uart_remove_one_port(&cpm_reg, &cpm_uart_ports[con].port); } + return ret; +} +static void __exit cpm_uart_exit(void) +{ + driver_unregister(&cpm_scc_uart_driver); + driver_unregister(&cpm_smc_uart_driver); uart_unregister_driver(&cpm_reg); } diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c index d789ee55cbb..17406a05ce1 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c @@ -8,6 +8,8 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * (C) 2004 Intracom, S.A. + * (C) 2006 MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -81,58 +83,11 @@ void cpm_line_cr_cmd(int line, int cmd) void smc1_lineif(struct uart_cpm_port *pinfo) { - volatile cpm8xx_t *cp = cpmp; - - (void)cp; /* fix warning */ -#if defined (CONFIG_MPC885ADS) - /* Enable SMC1 transceivers */ - { - cp->cp_pepar |= 0x000000c0; - cp->cp_pedir &= ~0x000000c0; - cp->cp_peso &= ~0x00000040; - cp->cp_peso |= 0x00000080; - } -#elif defined (CONFIG_MPC86XADS) - unsigned int iobits = 0x000000c0; - - if (!pinfo->is_portb) { - cp->cp_pbpar |= iobits; - cp->cp_pbdir &= ~iobits; - cp->cp_pbodr &= ~iobits; - } else { - ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits; - } -#endif pinfo->brg = 1; } void smc2_lineif(struct uart_cpm_port *pinfo) { - volatile cpm8xx_t *cp = cpmp; - - (void)cp; /* fix warning */ -#if defined (CONFIG_MPC885ADS) - cp->cp_pepar |= 0x00000c00; - cp->cp_pedir &= ~0x00000c00; - cp->cp_peso &= ~0x00000400; - cp->cp_peso |= 0x00000800; -#elif defined (CONFIG_MPC86XADS) - unsigned int iobits = 0x00000c00; - - if (!pinfo->is_portb) { - cp->cp_pbpar |= iobits; - cp->cp_pbdir &= ~iobits; - cp->cp_pbodr &= ~iobits; - } else { - ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits; - ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits; - } - -#endif - pinfo->brg = 2; } @@ -191,7 +146,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) /* was hostalloc but changed cause it blows away the */ /* large tlb mapping when pinning the kernel area */ mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8)); - dma_addr = 0; + dma_addr = (u32)mem_addr; } else mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr, GFP_KERNEL); @@ -204,8 +159,9 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) } pinfo->dp_addr = dp_offset; - pinfo->mem_addr = mem_addr; - pinfo->dma_addr = dma_addr; + pinfo->mem_addr = mem_addr; /* virtual address*/ + pinfo->dma_addr = dma_addr; /* physical address*/ + pinfo->mem_size = memsz; pinfo->rx_buf = mem_addr; pinfo->tx_buf = pinfo->rx_buf + L1_CACHE_ALIGN(pinfo->rx_nrfifos diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index fd9e53ed3fe..4b2de08f46d 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c @@ -8,6 +8,8 @@ * * Copyright (C) 2004 Freescale Semiconductor, Inc. * (C) 2004 Intracom, S.A. + * (C) 2006 MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -142,14 +144,6 @@ void scc2_lineif(struct uart_cpm_port *pinfo) * be supported in a sane fashion. */ #ifndef CONFIG_STX_GP3 -#ifdef CONFIG_MPC8560_ADS - volatile iop_cpm2_t *io = &cpm2_immr->im_ioport; - io->iop_ppard |= 0x00000018; - io->iop_psord &= ~0x00000008; /* Rx */ - io->iop_psord &= ~0x00000010; /* Tx */ - io->iop_pdird &= ~0x00000008; /* Rx */ - io->iop_pdird |= 0x00000010; /* Tx */ -#else volatile iop_cpm2_t *io = &cpm2_immr->im_ioport; io->iop_pparb |= 0x008b0000; io->iop_pdirb |= 0x00880000; @@ -157,7 +151,6 @@ void scc2_lineif(struct uart_cpm_port *pinfo) io->iop_pdirb &= ~0x00030000; io->iop_psorb &= ~0x00030000; #endif -#endif cpm2_immr->im_cpmux.cmx_scr &= 0xff00ffff; cpm2_immr->im_cpmux.cmx_scr |= 0x00090000; pinfo->brg = 2; @@ -218,8 +211,10 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) + L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize); - if (is_con) + if (is_con) { mem_addr = alloc_bootmem(memsz); + dma_addr = mem_addr; + } else mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr, GFP_KERNEL); @@ -234,6 +229,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) pinfo->dp_addr = dp_offset; pinfo->mem_addr = mem_addr; pinfo->dma_addr = dma_addr; + pinfo->mem_size = memsz; pinfo->rx_buf = mem_addr; pinfo->tx_buf = pinfo->rx_buf + L1_CACHE_ALIGN(pinfo->rx_nrfifos diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index c3b7a6673e9..d202eb4f384 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -45,6 +45,7 @@ #include <asm/io.h> #include <asm/irq.h> #include <asm/hardware.h> +#include <asm/arch/imx-uart.h> /* We've been assigned a range on the "Low-density serial ports" major */ #define SERIAL_IMX_MAJOR 204 @@ -73,7 +74,8 @@ struct imx_port { struct uart_port port; struct timer_list timer; unsigned int old_status; - int txirq,rxirq,rtsirq; + int txirq,rxirq,rtsirq; + int have_rtscts:1; }; /* @@ -491,8 +493,12 @@ imx_set_termios(struct uart_port *port, struct termios *termios, ucr2 = UCR2_SRST | UCR2_IRTS; if (termios->c_cflag & CRTSCTS) { - ucr2 &= ~UCR2_IRTS; - ucr2 |= UCR2_CTSC; + if( sport->have_rtscts ) { + ucr2 &= ~UCR2_IRTS; + ucr2 |= UCR2_CTSC; + } else { + termios->c_cflag &= ~CRTSCTS; + } } if (termios->c_cflag & CSTOPB) @@ -719,27 +725,6 @@ static void __init imx_init_ports(void) imx_ports[i].timer.function = imx_timeout; imx_ports[i].timer.data = (unsigned long)&imx_ports[i]; } - - imx_gpio_mode(PC9_PF_UART1_CTS); - imx_gpio_mode(PC10_PF_UART1_RTS); - imx_gpio_mode(PC11_PF_UART1_TXD); - imx_gpio_mode(PC12_PF_UART1_RXD); - imx_gpio_mode(PB28_PF_UART2_CTS); - imx_gpio_mode(PB29_PF_UART2_RTS); - - imx_gpio_mode(PB30_PF_UART2_TXD); - imx_gpio_mode(PB31_PF_UART2_RXD); - -#if 0 /* We don't need these, on the mx1 the _modem_ side of the uart - * is implemented. - */ - imx_gpio_mode(PD7_AF_UART2_DTR); - imx_gpio_mode(PD8_AF_UART2_DCD); - imx_gpio_mode(PD9_AF_UART2_RI); - imx_gpio_mode(PD10_AF_UART2_DSR); -#endif - - } #ifdef CONFIG_SERIAL_IMX_CONSOLE @@ -932,7 +917,14 @@ static int serial_imx_resume(struct platform_device *dev) static int serial_imx_probe(struct platform_device *dev) { + struct imxuart_platform_data *pdata; + imx_ports[dev->id].port.dev = &dev->dev; + + pdata = (struct imxuart_platform_data *)dev->dev.platform_data; + if(pdata && (pdata->flags & IMXUART_HAVE_RTSCTS)) + imx_ports[dev->id].have_rtscts = 1; + uart_add_one_port(&imx_reg, &imx_ports[dev->id].port); platform_set_drvdata(dev, &imx_ports[dev->id]); return 0; diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index fcd7744c425..aeb8153ccf2 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -1500,20 +1500,18 @@ uart_block_til_ready(struct file *filp, struct uart_state *state) static struct uart_state *uart_get(struct uart_driver *drv, int line) { struct uart_state *state; + int ret = 0; - mutex_lock(&port_mutex); state = drv->state + line; if (mutex_lock_interruptible(&state->mutex)) { - state = ERR_PTR(-ERESTARTSYS); - goto out; + ret = -ERESTARTSYS; + goto err; } state->count++; - if (!state->port) { - state->count--; - mutex_unlock(&state->mutex); - state = ERR_PTR(-ENXIO); - goto out; + if (!state->port || state->port->flags & UPF_DEAD) { + ret = -ENXIO; + goto err_unlock; } if (!state->info) { @@ -1531,15 +1529,17 @@ static struct uart_state *uart_get(struct uart_driver *drv, int line) tasklet_init(&state->info->tlet, uart_tasklet_action, (unsigned long)state); } else { - state->count--; - mutex_unlock(&state->mutex); - state = ERR_PTR(-ENOMEM); + ret = -ENOMEM; + goto err_unlock; } } - - out: - mutex_unlock(&port_mutex); return state; + + err_unlock: + state->count--; + mutex_unlock(&state->mutex); + err: + return ERR_PTR(ret); } /* @@ -2085,45 +2085,6 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state, } } -/* - * This reverses the effects of uart_configure_port, hanging up the - * port before removal. - */ -static void -uart_unconfigure_port(struct uart_driver *drv, struct uart_state *state) -{ - struct uart_port *port = state->port; - struct uart_info *info = state->info; - - if (info && info->tty) - tty_vhangup(info->tty); - - mutex_lock(&state->mutex); - - state->info = NULL; - - /* - * Free the port IO and memory resources, if any. - */ - if (port->type != PORT_UNKNOWN) - port->ops->release_port(port); - - /* - * Indicate that there isn't a port here anymore. - */ - port->type = PORT_UNKNOWN; - - /* - * Kill the tasklet, and free resources. - */ - if (info) { - tasklet_kill(&info->tlet); - kfree(info); - } - - mutex_unlock(&state->mutex); -} - static struct tty_operations uart_ops = { .open = uart_open, .close = uart_close, @@ -2270,6 +2231,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) state = drv->state + port->line; mutex_lock(&port_mutex); + mutex_lock(&state->mutex); if (state->port) { ret = -EINVAL; goto out; @@ -2304,7 +2266,13 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) port->cons && !(port->cons->flags & CON_ENABLED)) register_console(port->cons); + /* + * Ensure UPF_DEAD is not set. + */ + port->flags &= ~UPF_DEAD; + out: + mutex_unlock(&state->mutex); mutex_unlock(&port_mutex); return ret; @@ -2322,6 +2290,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) int uart_remove_one_port(struct uart_driver *drv, struct uart_port *port) { struct uart_state *state = drv->state + port->line; + struct uart_info *info; BUG_ON(in_interrupt()); @@ -2332,11 +2301,48 @@ int uart_remove_one_port(struct uart_driver *drv, struct uart_port *port) mutex_lock(&port_mutex); /* + * Mark the port "dead" - this prevents any opens from + * succeeding while we shut down the port. + */ + mutex_lock(&state->mutex); + port->flags |= UPF_DEAD; + mutex_unlock(&state->mutex); + + /* * Remove the devices from devfs */ tty_unregister_device(drv->tty_driver, port->line); - uart_unconfigure_port(drv, state); + info = state->info; + if (info && info->tty) + tty_vhangup(info->tty); + + /* + * All users of this port should now be disconnected from + * this driver, and the port shut down. We should be the + * only thread fiddling with this port from now on. + */ + state->info = NULL; + + /* + * Free the port IO and memory resources, if any. + */ + if (port->type != PORT_UNKNOWN) + port->ops->release_port(port); + + /* + * Indicate that there isn't a port here anymore. + */ + port->type = PORT_UNKNOWN; + + /* + * Kill the tasklet, and free resources. + */ + if (info) { + tasklet_kill(&info->tlet); + kfree(info); + } + state->port = NULL; mutex_unlock(&port_mutex); |