diff options
Diffstat (limited to 'drivers/usb/host/xhci.h')
| -rw-r--r-- | drivers/usb/host/xhci.h | 452 |
1 files changed, 452 insertions, 0 deletions
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h new file mode 100644 index 00000000000..a4d44aad069 --- /dev/null +++ b/drivers/usb/host/xhci.h @@ -0,0 +1,452 @@ +/* + * xHCI host controller driver + * + * Copyright (C) 2008 Intel Corp. + * + * Author: Sarah Sharp + * Some code borrowed from the Linux EHCI driver. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY + * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software Foundation, + * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __LINUX_XHCI_HCD_H +#define __LINUX_XHCI_HCD_H + +#include <linux/usb.h> + +#include "../core/hcd.h" +/* Code sharing between pci-quirks and xhci hcd */ +#include "xhci-ext-caps.h" + +/* xHCI PCI Configuration Registers */ +#define XHCI_SBRN_OFFSET (0x60) + +/* + * xHCI register interface. + * This corresponds to the eXtensible Host Controller Interface (xHCI) + * Revision 0.95 specification + * + * Registers should always be accessed with double word or quad word accesses. + * + * Some xHCI implementations may support 64-bit address pointers. Registers + * with 64-bit address pointers should be written to with dword accesses by + * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second. + * xHCI implementations that do not support 64-bit address pointers will ignore + * the high dword, and write order is irrelevant. + */ + +/** + * struct xhci_cap_regs - xHCI Host Controller Capability Registers. + * @hc_capbase: length of the capabilities register and HC version number + * @hcs_params1: HCSPARAMS1 - Structural Parameters 1 + * @hcs_params2: HCSPARAMS2 - Structural Parameters 2 + * @hcs_params3: HCSPARAMS3 - Structural Parameters 3 + * @hcc_params: HCCPARAMS - Capability Parameters + * @db_off: DBOFF - Doorbell array offset + * @run_regs_off: RTSOFF - Runtime register space offset + */ +struct xhci_cap_regs { + u32 hc_capbase; + u32 hcs_params1; + u32 hcs_params2; + u32 hcs_params3; + u32 hcc_params; + u32 db_off; + u32 run_regs_off; + /* Reserved up to (CAPLENGTH - 0x1C) */ +} __attribute__ ((packed)); + +/* hc_capbase bitmasks */ +/* bits 7:0 - how long is the Capabilities register */ +#define HC_LENGTH(p) XHCI_HC_LENGTH(p) +/* bits 31:16 */ +#define HC_VERSION(p) (((p) >> 16) & 0xffff) + +/* HCSPARAMS1 - hcs_params1 - bitmasks */ +/* bits 0:7, Max Device Slots */ +#define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff) +#define HCS_SLOTS_MASK 0xff +/* bits 8:18, Max Interrupters */ +#define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff) +/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */ +#define HCS_MAX_PORTS(p) (((p) >> 24) & 0x7f) + +/* HCSPARAMS2 - hcs_params2 - bitmasks */ +/* bits 0:3, frames or uframes that SW needs to queue transactions + * ahead of the HW to meet periodic deadlines */ +#define HCS_IST(p) (((p) >> 0) & 0xf) +/* bits 4:7, max number of Event Ring segments */ +#define HCS_ERST_MAX(p) (((p) >> 4) & 0xf) +/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */ +/* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */ + +/* HCSPARAMS3 - hcs_params3 - bitmasks */ +/* bits 0:7, Max U1 to U0 latency for the roothub ports */ +#define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff) +/* bits 16:31, Max U2 to U0 latency for the roothub ports */ +#define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff) + +/* HCCPARAMS - hcc_params - bitmasks */ +/* true: HC can use 64-bit address pointers */ +#define HCC_64BIT_ADDR(p) ((p) & (1 << 0)) +/* true: HC can do bandwidth negotiation */ +#define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1)) +/* true: HC uses 64-byte Device Context structures + * FIXME 64-byte context structures aren't supported yet. + */ +#define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2)) +/* true: HC has port power switches */ +#define HCC_PPC(p) ((p) & (1 << 3)) +/* true: HC has port indicators */ +#define HCS_INDICATOR(p) ((p) & (1 << 4)) +/* true: HC has Light HC Reset Capability */ +#define HCC_LIGHT_RESET(p) ((p) & (1 << 5)) +/* true: HC supports latency tolerance messaging */ +#define HCC_LTC(p) ((p) & (1 << 6)) +/* true: no secondary Stream ID Support */ +#define HCC_NSS(p) ((p) & (1 << 7)) +/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */ +#define HCC_MAX_PSA (1 << ((((p) >> 12) & 0xf) + 1)) +/* Extended Capabilities pointer from PCI base - section 5.3.6 */ +#define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p) + +/* db_off bitmask - bits 0:1 reserved */ +#define DBOFF_MASK (~0x3) + +/* run_regs_off bitmask - bits 0:4 reserved */ +#define RTSOFF_MASK (~0x1f) + + +/* Number of registers per port */ +#define NUM_PORT_REGS 4 + +/** + * struct xhci_op_regs - xHCI Host Controller Operational Registers. + * @command: USBCMD - xHC command register + * @status: USBSTS - xHC status register + * @page_size: This indicates the page size that the host controller + * supports. If bit n is set, the HC supports a page size + * of 2^(n+12), up to a 128MB page size. + * 4K is the minimum page size. + * @cmd_ring: CRP - 64-bit Command Ring Pointer + * @dcbaa_ptr: DCBAAP - 64-bit Device Context Base Address Array Pointer + * @config_reg: CONFIG - Configure Register + * @port_status_base: PORTSCn - base address for Port Status and Control + * Each port has a Port Status and Control register, + * followed by a Port Power Management Status and Control + * register, a Port Link Info register, and a reserved + * register. + * @port_power_base: PORTPMSCn - base address for + * Port Power Management Status and Control + * @port_link_base: PORTLIn - base address for Port Link Info (current + * Link PM state and control) for USB 2.1 and USB 3.0 + * devices. + */ +struct xhci_op_regs { + u32 command; + u32 status; + u32 page_size; + u32 reserved1; + u32 reserved2; + u32 dev_notification; + u32 cmd_ring[2]; + /* rsvd: offset 0x20-2F */ + u32 reserved3[4]; + u32 dcbaa_ptr[2]; + u32 config_reg; + /* rsvd: offset 0x3C-3FF */ + u32 reserved4[241]; + /* port 1 registers, which serve as a base address for other ports */ + u32 port_status_base; + u32 port_power_base; + u32 port_link_base; + u32 reserved5; + /* registers for ports 2-255 */ + u32 reserved6[NUM_PORT_REGS*254]; +} __attribute__ ((packed)); + +/* USBCMD - USB command - command bitmasks */ +/* start/stop HC execution - do not write unless HC is halted*/ +#define CMD_RUN XHCI_CMD_RUN +/* Reset HC - resets internal HC state machine and all registers (except + * PCI config regs). HC does NOT drive a USB reset on the downstream ports. + * The xHCI driver must reinitialize the xHC after setting this bit. + */ +#define CMD_RESET (1 << 1) +/* Event Interrupt Enable - a '1' allows interrupts from the host controller */ +#define CMD_EIE XHCI_CMD_EIE +/* Host System Error Interrupt Enable - get out-of-band signal for HC errors */ +#define CMD_HSEIE XHCI_CMD_HSEIE +/* bits 4:6 are reserved (and should be preserved on writes). */ +/* light reset (port status stays unchanged) - reset completed when this is 0 */ +#define CMD_LRESET (1 << 7) +/* FIXME: ignoring host controller save/restore state for now. */ +#define CMD_CSS (1 << 8) +#define CMD_CRS (1 << 9) +/* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */ +#define CMD_EWE XHCI_CMD_EWE +/* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root + * hubs are in U3 (selective suspend), disconnect, disabled, or powered-off. + * '0' means the xHC can power it off if all ports are in the disconnect, + * disabled, or powered-off state. + */ +#define CMD_PM_INDEX (1 << 11) +/* bits 12:31 are reserved (and should be preserved on writes). */ + +/* USBSTS - USB status - status bitmasks */ +/* HC not running - set to 1 when run/stop bit is cleared. */ +#define STS_HALT XHCI_STS_HALT +/* serious error, e.g. PCI parity error. The HC will clear the run/stop bit. */ +#define STS_FATAL (1 << 2) +/* event interrupt - clear this prior to clearing any IP flags in IR set*/ +#define STS_EINT (1 << 3) +/* port change detect */ +#define STS_PORT (1 << 4) +/* bits 5:7 reserved and zeroed */ +/* save state status - '1' means xHC is saving state */ +#define STS_SAVE (1 << 8) +/* restore state status - '1' means xHC is restoring state */ +#define STS_RESTORE (1 << 9) +/* true: save or restore error */ +#define STS_SRE (1 << 10) +/* true: Controller Not Ready to accept doorbell or op reg writes after reset */ +#define STS_CNR XHCI_STS_CNR +/* true: internal Host Controller Error - SW needs to reset and reinitialize */ +#define STS_HCE (1 << 12) +/* bits 13:31 reserved and should be preserved */ + +/* + * DNCTRL - Device Notification Control Register - dev_notification bitmasks + * Generate a device notification event when the HC sees a transaction with a + * notification type that matches a bit set in this bit field. + */ +#define DEV_NOTE_MASK (0xffff) +#define ENABLE_DEV_NOTE(x) (1 << x) +/* Most of the device notification types should only be used for debug. + * SW does need to pay attention to function wake notifications. + */ +#define DEV_NOTE_FWAKE ENABLE_DEV_NOTE(1) + +/* CONFIG - Configure Register - config_reg bitmasks */ +/* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */ +#define MAX_DEVS(p) ((p) & 0xff) +/* bits 8:31 - reserved and should be preserved */ + +/* PORTSC - Port Status and Control Register - port_status_base bitmasks */ +/* true: device connected */ +#define PORT_CONNECT (1 << 0) +/* true: port enabled */ +#define PORT_PE (1 << 1) +/* bit 2 reserved and zeroed */ +/* true: port has an over-current condition */ +#define PORT_OC (1 << 3) +/* true: port reset signaling asserted */ +#define PORT_RESET (1 << 4) +/* Port Link State - bits 5:8 + * A read gives the current link PM state of the port, + * a write with Link State Write Strobe set sets the link state. + */ +/* true: port has power (see HCC_PPC) */ +#define PORT_POWER (1 << 9) +/* bits 10:13 indicate device speed: + * 0 - undefined speed - port hasn't be initialized by a reset yet + * 1 - full speed + * 2 - low speed + * 3 - high speed + * 4 - super speed + * 5-15 reserved + */ +#define DEV_SPEED_MASK (0xf<<10) +#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10)) +#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == (0x1<<10)) +#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == (0x2<<10)) +#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == (0x3<<10)) +#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == (0x4<<10)) +/* Port Indicator Control */ +#define PORT_LED_OFF (0 << 14) +#define PORT_LED_AMBER (1 << 14) +#define PORT_LED_GREEN (2 << 14) +#define PORT_LED_MASK (3 << 14) +/* Port Link State Write Strobe - set this when changing link state */ +#define PORT_LINK_STROBE (1 << 16) +/* true: connect status change */ +#define PORT_CSC (1 << 17) +/* true: port enable change */ +#define PORT_PEC (1 << 18) +/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port + * into an enabled state, and the device into the default state. A "warm" reset + * also resets the link, forcing the device through the link training sequence. + * SW can also look at the Port Reset register to see when warm reset is done. + */ +#define PORT_WRC (1 << 19) +/* true: over-current change */ +#define PORT_OCC (1 << 20) +/* true: reset change - 1 to 0 transition of PORT_RESET */ +#define PORT_RC (1 << 21) +/* port link status change - set on some port link state transitions: + * Transition Reason + * ------------------------------------------------------------------------------ + * - U3 to Resume Wakeup signaling from a device + * - Resume to Recovery to U0 USB 3.0 device resume + * - Resume to U0 USB 2.0 device resume + * - U3 to Recovery to U0 Software resume of USB 3.0 device complete + * - U3 to U0 Software resume of USB 2.0 device complete + * - U2 to U0 L1 resume of USB 2.1 device complete + * - U0 to U0 (???) L1 entry rejection by USB 2.1 device + * - U0 to disabled L1 entry error with USB 2.1 device + * - Any state to inactive Error on USB 3.0 port + */ +#define PORT_PLC (1 << 22) +/* port configure error change - port failed to configure its link partner */ +#define PORT_CEC (1 << 23) +/* bit 24 reserved */ +/* wake on connect (enable) */ +#define PORT_WKCONN_E (1 << 25) +/* wake on disconnect (enable) */ +#define PORT_WKDISC_E (1 << 26) +/* wake on over-current (enable) */ +#define PORT_WKOC_E (1 << 27) +/* bits 28:29 reserved */ +/* true: device is removable - for USB 3.0 roothub emulation */ +#define PORT_DEV_REMOVE (1 << 30) +/* Initiate a warm port reset - complete when PORT_WRC is '1' */ +#define PORT_WR (1 << 31) + +/* Port Power Management Status and Control - port_power_base bitmasks */ +/* Inactivity timer value for transitions into U1, in microseconds. + * Timeout can be up to 127us. 0xFF means an infinite timeout. + */ +#define PORT_U1_TIMEOUT(p) ((p) & 0xff) +/* Inactivity timer value for transitions into U2 */ +#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8) +/* Bits 24:31 for port testing */ + + +/** + * struct intr_reg - Interrupt Register Set + * @irq_pending: IMAN - Interrupt Management Register. Used to enable + * interrupts and check for pending interrupts. + * @irq_control: IMOD - Interrupt Moderation Register. + * Used to throttle interrupts. + * @erst_size: Number of segments in the Event Ring Segment Table (ERST). + * @erst_base: ERST base address. + * @erst_dequeue: Event ring dequeue pointer. + * + * Each interrupter (defined by a MSI-X vector) has an event ring and an Event + * Ring Segment Table (ERST) associated with it. The event ring is comprised of + * multiple segments of the same size. The HC places events on the ring and + * "updates the Cycle bit in the TRBs to indicate to software the current + * position of the Enqueue Pointer." The HCD (Linux) processes those events and + * updates the dequeue pointer. + */ +struct intr_reg { + u32 irq_pending; + u32 irq_control; + u32 erst_size; + u32 rsvd; + u32 erst_base[2]; + u32 erst_dequeue[2]; +} __attribute__ ((packed)); + +#define ER_IRQ_PENDING(p) ((p) & 0x1) +#define ER_IRQ_ENABLE(p) ((p) | 0x2) +/* Preserve bits 16:31 of erst_size */ +#define ERST_SIZE_MASK (0xffff<<16) + +/** + * struct xhci_run_regs + * @microframe_index: + * MFINDEX - current microframe number + * + * Section 5.5 Host Controller Runtime Registers: + * "Software should read and write these registers using only Dword (32 bit) + * or larger accesses" + */ +struct xhci_run_regs { + u32 microframe_index; + u32 rsvd[7]; + struct intr_reg ir_set[128]; +} __attribute__ ((packed)); + + +/* There is one ehci_hci structure per controller */ +struct xhci_hcd { + /* glue to PCI and HCD framework */ + struct xhci_cap_regs __iomem *cap_regs; + struct xhci_op_regs __iomem *op_regs; + struct xhci_run_regs __iomem *run_regs; + + /* Cached register copies of read-only HC data */ + __u32 hcs_params1; + __u32 hcs_params2; + __u32 hcs_params3; + __u32 hcc_params; + + spinlock_t lock; + + /* packed release number */ + u8 sbrn; + u16 hci_version; + u8 max_slots; + u8 max_interrupters; + u8 max_ports; + u8 isoc_threshold; + int event_ring_max; + int addr_64; + int page_size; +}; + +/* convert between an HCD pointer and the corresponding EHCI_HCD */ +static inline struct xhci_hcd *hcd_to_xhci(struct usb_hcd *hcd) +{ + return (struct xhci_hcd *) (hcd->hcd_priv); +} + +static inline struct usb_hcd *xhci_to_hcd(struct xhci_hcd *xhci) +{ + return container_of((void *) xhci, struct usb_hcd, hcd_priv); +} + +#ifdef CONFIG_USB_XHCI_HCD_DEBUGGING +#define XHCI_DEBUG 1 +#else +#define XHCI_DEBUG 0 +#endif + +#define xhci_dbg(xhci, fmt, args...) \ + do { if (XHCI_DEBUG) dev_dbg(xhci_to_hcd(xhci)->self.controller , fmt , ## args); } while (0) +#define xhci_info(xhci, fmt, args...) \ + do { if (XHCI_DEBUG) dev_info(xhci_to_hcd(xhci)->self.controller , fmt , ## args); } while (0) +#define xhci_err(xhci, fmt, args...) \ + dev_err(xhci_to_hcd(xhci)->self.controller , fmt , ## args) +#define xhci_warn(xhci, fmt, args...) \ + dev_warn(xhci_to_hcd(xhci)->self.controller , fmt , ## args) + +/* TODO: copied from ehci.h - can be refactored? */ +/* xHCI spec says all registers are little endian */ +static inline unsigned int xhci_readl(const struct xhci_hcd *xhci, + __u32 __iomem *regs) +{ + return readl(regs); +} +static inline void xhci_writel(const struct xhci_hcd *xhci, + const unsigned int val, __u32 __iomem *regs) +{ + if (!in_interrupt()) + xhci_dbg(xhci, "`MEM_WRITE_DWORD(3'b000, 32'h%0x, 32'h%0x, 4'hf);\n", + (unsigned int) regs, val); + writel(val, regs); +} + +#endif /* __LINUX_XHCI_HCD_H */ |