| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This patch ensures that no console data will go the UART while
the GSM mux is switched to the GSM. This is necessary despite
the code that disables the console due to the fact that the
console resumes before the neo1973_pm_gsm driver, and consoles
always resume in the "on" state.
Signed-off-by: Mike Westerhof <mwester@dls.net>
|
|
gta0x-log-serial-rx-error.patch
This patch causes a KERN_DEBUG message to be printed each time an
error status is read from a UART. This is intended to facilitate
the reporting of more useful problem and bug reports from users
in the field.
Signed-off-by: Mike Westerhof <mwester@dls.net>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This patch introduces a new resume debugging concept: if we
get an OOPS inbetween starting suspend and finishing resume, it
uses a new "emergency spew" device similar to BUT NOT REQUIRING
CONFIG_DEBUG_LL to dump the syslog buffer and then the OOPS
on the debug device defined by the existing CONFIG_DEBUG_S3C_UART
index. But neither CONFIG_DEBUG_LL nor the S3C low level configs
are needed to use this feature.
Another difference between this feature and CONFIG_DEBUG_LL is that
it does not affect resume timing, ordering or UART traffic UNLESS
there is an OOPS during resume.
The patch adds three global exports, one to say if we are inside
suspend / resume, and two callbacks for printk() to use to init
and dump the emergency data. The callbacks are set in s3c serial
device init, but the whole structure is arch independent.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This is a temporary work-around Mike Westerhof for this bug:
http://bugzilla.openmoko.org/cgi-bin/bugzilla/show_bug.cgi?id=788
See also
http://lists.openmoko.org/pipermail/openmoko-kernel/2008-February/000804.html
(It's the 2nd option.)
We may settle on a different solution in the future, depending on
feedback from upstream.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into rmk-next
|
|
The atmel_serial driver is mismanaging its clock by leaving it on at all
times ... the whole point of clock management is to leave it off unless
it's actively needed, which conserves power!!
Although the kernel doesn't actually hang without my fix, it does
discard quite a lot of early console output.
The result still looks correct:
usart users= 1 on 35000000 Hz, for atmel_usart.0
usart users= 0 off 35000000 Hz, for atmel_usart.2
when using ttyS0 as serial console.
[haavard.skinnemoen@atmel.com: Make sure clock is enabled early for console]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into rmk-next
|
|
Fix the usage of CONFIG_SERIAL_SAMSUNG_UARTS in several places
in the kernel where it had been missed. This finishes fixing a
long standing issue where S3C2443 and S3C64XX could not use the
4th UART
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Update the serial driver to handle the 4 ports of the
S3C2443 and S364XX series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
* 'cris_move' of git://www.jni.nu/cris:
[CRIS] Move header files from include to arch/cris/include.
[CRISv32] Remove warning in io.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into s3c64xx
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
SH4-202 doesn't have SCSXX1. But it is treated so that there is SCSPTR1 in
current code. This patch add sci_rxd_in of SH4-202.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This change a name of SCSPTR used in sci_rxd_in of SH5-101.
SCSPTR is not declared and will become the error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Make the netX serial driver tristate (as the help text implied). Make the
serial driver build correctly if the netX serial console is disabled. Do not
allow the netX serial console if the netX serial driver is build as a module.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Change all users of header files to correct path.
Remove some unneeded headers for arch-v32.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
This reverts commit 5ca8c4852fcbbc8a8497c4ee8b2a0a7466f3524c.
With the killing off of SCIF_ONLY and its spawn in sh-sci, we no longer
require this change, so just revert it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
SH 7366 has compile bug.
because there is no SCIF_ONLY for SH 7366.
this patch add it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into s3c64xx
Conflicts:
arch/arm/mm/Kconfig
|
|
These have the Mainpine PCI identifier on however
Additional paranoia check for Tornado versions added by Alan Cox
(and this time I remembered to do an stg refresh so that the corrections ended
up in these patches not randomly attached to another diff -- Alan)
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the OxSemi 'Tornado' devices.
Reformatted and reworked a bit by Alan Cox
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] clps711x: add sparsemem definitions
[ARM] 5315/1: Fix section mismatch warning (sa1111)
[ARM] Orion: activate workaround for 88f6183 SPI clock erratum
[ARM] Orion: instantiate the dsa switch driver
[ARM] mv78xx0: force link speed/duplex on eth2/eth3
[ARM] remove extra brace in arch/arm/mach-pxa/trizeps4.c
[ARM] balance parenthesis in header file
[ARM] pxa: fix trizeps PCMCIA build
[ARM] pxa: fix trizeps defconfig
[ARM] dmabounce requires ZONE_DMA
[ARM] 5303/1: period_cycles should be greater than 1
[ARM] 5310/1: Fix cache flush functions for ARMv4
[ARM] pxa: fix 3bca103a1e658d23737d20e1989139d9ca8973bf
[ARM] pxa: fix redefinition of NR_IRQS
[ARM] S3C24XX: Fix redefine of DEFINE_TIMER() in s3c24xx pwm-clock.c
[ARM] S3C2443: Fix HCLK rate
[ARM] S3C24XX: Serial driver debug depends on DEBUG_LL
[ARM] S3C24XX: pwm-clock set_parent mask fix
|
|
The S3C64XX code changes the order of the serial
interrupts, so change the registration process to
pickup the extra IRQ resources.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support to the Samsung serial driver for the S3C6400
and S3C6410 serial ports.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for CPU frequency scalling to the S3C24XX serial
driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into s3c64xx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
|
|
In function sn_sal_switch_to_asynch(): drivers/serial/sn_console.c:713:
HZ * SN_SAL_UART_FIFO_DEPTH / SN_SAL_UART_FIFO_SPEED_CPS;
After preprocessing (see defines in patch) this becomes HZ * 16 / 9600 / 10
(associativity from left to right), not equivalent to HZ * 16 / 960.
Looks-obviously-right-to: Tony Luck <tony.luck@intel.com>
Cc: Jes Sorensen <jes@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch makes the needlessly global probe_serial_gsc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a warning caused by commit 0c8946d97ae7d2d6691f8290a10faa63453b63f8
(serial: Make uart_port's ioport "unsigned long".)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Josip Rodin <joy@entuzijast.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SH7723 has two types of SCIF (SCIF and SCIFA).
The current sh-sci driver supports only SCIFA, and calculation methods of SCBRR
are different.
This patch support this methods.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
Documentation/kernel-parameters.txt
arch/sh/include/asm/elf.h
|
|
|
|
s3c64xx
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits)
[ARM] 5308/1: Fix Viper ISA IRQ handling
[ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error
[ARM] 5306/1: pxa: fix build error on CM-X270
[ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict
[ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check
[ARM] 5301/1: ARM: OMAP: Add missing irq defines
ARM: OMAP3: Add default kernel config for OMAP LDP
ARM: OMAP3: Add basic board support for OMAP LDP
ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add support for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add Beagle defconfig
ARM: OMAP3: Add minimal Beagle board support
ARM: OMAP3: Add minimal omap3430 support
ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code
ARM: OMAP: Fixes to omap_mcbsp_request function
ARM: OMAP: Add support for OMAP2430 in McBSP
ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx
ARM: OMAP: Allocate McBSP devices dynamically
Fix sections for omap-mcbsp platform driver
[ARM] S3C24XX: Additional include moves
...
|
|
The SERIAL_SAMSUNG_DEBUG used printascii() to avoid debugging
through itself when selected as a console. Disable this option
when DEBUG_LL is not set (printascii is unavailable).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Works on my test box with a quick test.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Conflicts:
arch/arm/mach-versatile/core.c
|
|
Manual fixup of conflicts on:
arch/powerpc/include/asm/dcr-regs.h
drivers/net/ibm_newemac/core.h
|
