1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
|
/*
* Low-Level PCI Support for the SH7780
*
* Dustin McIntire (dustin@sensoria.com)
* Derived from arch/i386/kernel/pci-*.c which bore the message:
* (c) 1999--2000 Martin Mares <mj@ucw.cz>
*
* Ported to the new API by Paul Mundt <lethal@linux-sh.org>
* With cleanup by Paul van Gool <pvangool@mimotech.com>
*
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
*/
#undef DEBUG
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include "pci-sh4.h"
#define INTC_BASE 0xffd00000
#define INTC_ICR0 (INTC_BASE+0x0)
#define INTC_ICR1 (INTC_BASE+0x1c)
#define INTC_INTPRI (INTC_BASE+0x10)
#define INTC_INTREQ (INTC_BASE+0x24)
#define INTC_INTMSK0 (INTC_BASE+0x44)
#define INTC_INTMSK1 (INTC_BASE+0x48)
#define INTC_INTMSK2 (INTC_BASE+0x40080)
#define INTC_INTMSKCLR0 (INTC_BASE+0x64)
#define INTC_INTMSKCLR1 (INTC_BASE+0x68)
#define INTC_INTMSKCLR2 (INTC_BASE+0x40084)
#define INTC_INT2MSKR (INTC_BASE+0x40038)
#define INTC_INT2MSKCR (INTC_BASE+0x4003c)
/*
* Initialization. Try all known PCI access methods. Note that we support
* using both PCI BIOS and direct access: in such cases, we use I/O ports
* to access config space.
*
* Note that the platform specific initialization (BSC registers, and memory
* space mapping) will be called via the platform defined function
* pcibios_init_platform().
*/
static int __init sh7780_pci_init(void)
{
unsigned int id;
int ret;
pr_debug("PCI: Starting intialization.\n");
outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */
/* check for SH7780/SH7780R hardware */
id = pci_read_reg(SH7780_PCIVID);
if ((id != ((SH7780_DEVICE_ID << 16) | SH7780_VENDOR_ID)) &&
(id != ((SH7781_DEVICE_ID << 16) | SH7780_VENDOR_ID))) {
printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id);
return -ENODEV;
}
/* Setup the INTC */
ctrl_outl(0x00200000, INTC_ICR0); /* INTC SH-4 Mode */
ctrl_outl(0x00078000, INTC_INT2MSKCR); /* enable PCIINTA - PCIINTD */
ctrl_outl(0x40000000, INTC_INTMSK1); /* disable IRL4-7 Interrupt */
ctrl_outl(0x0000fffe, INTC_INTMSK2); /* disable IRL4-7 Interrupt */
ctrl_outl(0x80000000, INTC_INTMSKCLR1); /* enable IRL0-3 Interrupt */
ctrl_outl(0xfffe0000, INTC_INTMSKCLR2); /* enable IRL0-3 Interrupt */
if ((ret = sh4_pci_check_direct()) != 0)
return ret;
return pcibios_init_platform();
}
core_initcall(sh7780_pci_init);
int __init sh7780_pcic_init(struct sh4_pci_address_map *map)
{
u32 word;
/*
* This code is unused for some boards as it is done in the
* bootloader and doing it here means the MAC addresses loaded
* by the bootloader get lost.
*/
if (!(map->flags & SH4_PCIC_NO_RESET)) {
/* toggle PCI reset pin */
word = SH4_PCICR_PREFIX | SH4_PCICR_PRST;
pci_write_reg(word, SH4_PCICR);
/* Wait for a long time... not 1 sec. but long enough */
mdelay(100);
word = SH4_PCICR_PREFIX;
pci_write_reg(word, SH4_PCICR);
}
/* set the command/status bits to:
* Wait Cycle Control + Parity Enable + Bus Master +
* Mem space enable
*/
pci_write_reg(0x00000046, SH7780_PCICMD);
/* define this host as the host bridge */
word = PCI_BASE_CLASS_BRIDGE << 24;
pci_write_reg(word, SH7780_PCIRID);
/* Set IO and Mem windows to local address
* Make PCI and local address the same for easy 1 to 1 mapping
* Window0 = map->window0.size @ non-cached area base = SDRAM
* Window1 = map->window1.size @ cached area base = SDRAM
*/
word = ((map->window0.size - 1) & 0x1ff00001) | 0x01;
pci_write_reg(0x07f00001, SH4_PCILSR0);
word = ((map->window1.size - 1) & 0x1ff00001) | 0x01;
pci_write_reg(0x00000001, SH4_PCILSR1);
/* Set the values on window 0 PCI config registers */
word = P2SEGADDR(map->window0.base);
pci_write_reg(0xa8000000, SH4_PCILAR0);
pci_write_reg(0x08000000, SH7780_PCIMBAR0);
/* Set the values on window 1 PCI config registers */
word = P2SEGADDR(map->window1.base);
pci_write_reg(0x00000000, SH4_PCILAR1);
pci_write_reg(0x00000000, SH7780_PCIMBAR1);
/* Map IO space into PCI IO window
* The IO window is 64K-PCIBIOS_MIN_IO in size
* IO addresses will be translated to the
* PCI IO window base address
*/
pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n",
PCIBIOS_MIN_IO, (64 << 10),
SH7780_PCI_IO_BASE + PCIBIOS_MIN_IO);
/* NOTE: I'm ignoring the PCI error IRQs for now..
* TODO: add support for the internal error interrupts and
* DMA interrupts...
*/
#ifdef CONFIG_SH_R7780RP
pci_fixup_pcic();
#endif
/* SH7780 init done, set central function init complete */
/* use round robin mode to stop a device starving/overruning */
word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_FTO;
pci_write_reg(word, SH4_PCICR);
return 1;
}
|
