path: root/drivers/input/touchscreen/Kconfig

#
# Touchscreen driver configuration
#
menuconfig INPUT_TOUCHSCREEN
	bool "Touchscreens"
	help
	  Say Y here, and a list of supported touchscreens will be displayed.
	  This option doesn't affect the kernel.

	  If unsure, say Y.

if INPUT_TOUCHSCREEN

config TOUCHSCREEN_ADS7846
	tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
	depends on SPI_MASTER
	depends on HWMON = n || HWMON
	help
	  Say Y here if you have a touchscreen interface using the
	  ADS7846/TSC2046 or ADS7843 controller, and your board-specific
	  setup code includes that in its table of SPI devices.

	  If HWMON is selected, and the driver is told the reference voltage
	  on your board, you will also get hwmon interfaces for the voltage
	  (and on ads7846/tsc2046, temperature) sensors of this chip.

	  If unsure, say N (but it's safe to say "Y").

	  To compile this driver as a module, choose M here: the
	  module will be called ads7846.

config TOUCHSCREEN_AD7877
	tristate "AD7877 based touchscreens"
	depends on SPI_MASTER
	help
	  Say Y here if you have a touchscreen interface using the
	  AD7877 controller, and your board-specific initialization
	  code includes that in its table of SPI devices.

	  If unsure, say N (but it's safe to say "Y").

	  To compile this driver as a module, choose M here: the
	  module will be called ad7877.

config TOUCHSCREEN_AD7879_I2C
	tristate "AD7879 based touchscreens: AD7879-1 I2C Interface"
	depends on I2C
	select TOUCHSCREEN_AD7879
	help
	  Say Y here if you have a touchscreen interface using the
	  AD7879-1/AD7889-1 controller, and your board-specific
	  initialization code includes that in its table of I2C devices.

	  If unsure, say N (but it's safe to say "Y").

	  To compile this driver as a module, choose M here: the
	  module will be called ad7879.

config TOUCHSCREEN_AD7879_SPI
	tristate "AD7879 based touchscreens: AD7879 SPI Interface"
	depends on SPI_MASTER && TOUCHSCREEN_AD7879_I2C = n
	select TOUCHSCREEN_AD7879
	help
	  Say Y here if you have a touchscreen interface using the
	  AD7879/AD7889 controller, and your board-specific initialization
	  code includes that in its table of SPI devices.

	  If unsure, say N (but it's safe to say "Y").

	  To compile this driver as a module, choose M here: the
	  module will be called ad7879.

config TOUCHSCREEN_AD7879
	tristate
	default n

config TOUCHSCREEN_BITSY
	tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
	depends on SA1100_BITSY
	select SERIO
	help
	  Say Y here if you have the h3600 (Bitsy) touchscreen.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called h3600_ts_input.

config TOUCHSCREEN_CORGI
	tristate "SharpSL (Corgi and Spitz series) touchscreen driver (DEPRECATED)"
	depends on PXA_SHARPSL
	select CORGI_SSP_DEPRECATED
	default y
	help
	  Say Y here to enable the driver for the touchscreen on the
	  Sharp SL-C7xx and SL-Cxx00 series of PDAs.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called corgi_ts.

	  NOTE: this driver is deprecated, try enable SPI and generic
	  ADS7846-based touchscreen driver.

config TOUCHSCREEN_DA9034
	tristate "Touchscreen support for Dialog Semiconductor DA9034"
	depends on PMIC_DA903X
	default y
	help
	  Say Y here to enable the support for the touchscreen found
	  on Dialog Semiconductor DA9034 PMIC.

config TOUCHSCREEN_DYNAPRO
	tristate "Dynapro serial touchscreen"
	select SERIO
	help
	  Say Y here if you have a Dynapro serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called dynapro.

config TOUCHSCREEN_EETI
	tristate "EETI touchscreen panel support"
	depends on I2C
	help
	  Say Y here to enable support for I2C connected EETI touch panels.

	  To compile this driver as a module, choose M here: the
	  module will be called eeti_ts.

config TOUCHSCREEN_FUJITSU
	tristate "Fujitsu serial touchscreen"
	select SERIO
	help
	  Say Y here if you have the Fujitsu touchscreen (such as one
	  installed in Lifebook P series laptop) connected to your
	  system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called fujitsu-ts.

config TOUCHSCREEN_S3C2410
	tristate "Samsung S3C2410 touchscreen input driver"
	depends on ARCH_S3C2410
	select S3C24XX_ADC
	help
	  Say Y here if you have the s3c2410 touchscreen.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called s3c2410_ts.

config TOUCHSCREEN_GUNZE
	tristate "Gunze AHL-51S touchscreen"
	select SERIO
	help
	  Say Y here if you have the Gunze AHL-51 touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called gunze.

config TOUCHSCREEN_ELO
	tristate "Elo serial touchscreens"
	select SERIO
	help
	  Say Y here if you have an Elo serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called elo.

config TOUCHSCREEN_WACOM_W8001
	tristate "Wacom W8001 penabled serial touchscreen"
	select SERIO
	help
	  Say Y here if you have an Wacom W8001 penabled serial touchscreen
	  connected to your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called wacom_w8001.

config TOUCHSCREEN_MCS5000
	tristate "MELFAS MCS-5000 touchscreen"
	depends on I2C
	help
	  Say Y here if you have the MELFAS MCS-5000 touchscreen controller
	  chip in your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called mcs5000_ts.

config TOUCHSCREEN_MTOUCH
	tristate "MicroTouch serial touchscreens"
	select SERIO
	help
	  Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called mtouch.

config TOUCHSCREEN_INEXIO
	tristate "iNexio serial touchscreens"
	select SERIO
	help
	  Say Y here if you have an iNexio serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called inexio.

config TOUCHSCREEN_MK712
	tristate "ICS MicroClock MK712 touchscreen"
	help
	  Say Y here if you have the ICS MicroClock MK712 touchscreen
	  controller chip in your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called mk712.

config TOUCHSCREEN_HP600
	tristate "HP Jornada 6xx touchscreen"
	depends on SH_HP6XX && SH_ADC
	help
	  Say Y here if you have a HP Jornada 620/660/680/690 and want to
          support the built-in touchscreen.

	  To compile this driver as a module, choose M here: the
	  module will be called hp680_ts_input.

config TOUCHSCREEN_HP7XX
	tristate "HP Jornada 7xx touchscreen"
	depends on SA1100_JORNADA720_SSP
	help
	  Say Y here if you have a HP Jornada 710/720/728 and want
	  to support the built-in touchscreen.

	  To compile this driver as a module, choose M here: the
	  module will be called jornada720_ts.

config TOUCHSCREEN_HTCPEN
	tristate "HTC Shift X9500 touchscreen"
	depends on ISA
	help
	  Say Y here if you have an HTC Shift UMPC also known as HTC X9500
	  Clio / Shangrila and want to support the built-in touchscreen.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called htcpen.

config TOUCHSCREEN_PENMOUNT
	tristate "Penmount serial touchscreen"
	select SERIO
	help
	  Say Y here if you have a Penmount serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called penmount.

config TOUCHSCREEN_MIGOR
	tristate "Renesas MIGO-R touchscreen"
	depends on SH_MIGOR && I2C
	help
	  Say Y here to enable MIGO-R touchscreen support.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called migor_ts.

config TOUCHSCREEN_TOUCHRIGHT
	tristate "Touchright serial touchscreen"
	select SERIO
	help
	  Say Y here if you have a Touchright serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called touchright.

config TOUCHSCREEN_TOUCHWIN
	tristate "Touchwin serial touchscreen"
	select SERIO
	help
	  Say Y here if you have a Touchwin serial touchscreen connected to
	  your system.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called touchwin.

config TOUCHSCREEN_ATMEL_TSADCC
	tristate "Atmel Touchscreen Interface"
	depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
	help
	  Say Y here if you have a 4-wire touchscreen connected to the
          ADC Controller on your Atmel SoC (such as the AT91SAM9RL).

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called atmel_tsadcc.

config TOUCHSCREEN_UCB1400
	tristate "Philips UCB1400 touchscreen"
	depends on AC97_BUS
	depends on UCB1400_CORE
	help
	  This enables support for the Philips UCB1400 touchscreen interface.
	  The UCB1400 is an AC97 audio codec.  The touchscreen interface
	  will be initialized only after the ALSA subsystem has been
	  brought up and the UCB1400 detected.  You therefore have to
	  configure ALSA support as well (either built-in or modular,
	  independently of whether this driver is itself built-in or
	  modular) for this driver to work.

	  To compile this driver as a module, choose M here: the
	  module will be called ucb1400_ts.

config TOUCHSCREEN_WM97XX
	tristate "Support for WM97xx AC97 touchscreen controllers"
	depends on AC97_BUS
	help
	  Say Y here if you have a Wolfson Microelectronics WM97xx
	  touchscreen connected to your system. Note that this option
	  only enables core driver, you will also need to select
	  support for appropriate chip below.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called wm97xx-ts.

config TOUCHSCREEN_WM9705
	bool "WM9705 Touchscreen interface support"
	depends on TOUCHSCREEN_WM97XX
	default y
	help
	  Say Y here to enable support for the Wolfson Microelectronics
	  WM9705 touchscreen controller.

config TOUCHSCREEN_WM9712
	bool "WM9712 Touchscreen interface support"
	depends on TOUCHSCREEN_WM97XX
	default y
	help
	  Say Y here to enable support for the Wolfson Microelectronics
	  WM9712 touchscreen controller.

config TOUCHSCREEN_WM9713
	bool "WM9713 Touchscreen interface support"
	depends on TOUCHSCREEN_WM97XX
	default y
	help
	  Say Y here to enable support for the Wolfson Microelectronics
	  WM9713 touchscreen controller.

config TOUCHSCREEN_WM97XX_ATMEL
	tristate "WM97xx Atmel accelerated touch"
	depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
	help
	  Say Y here for support for streaming mode with WM97xx touchscreens
	  on Atmel AT91 or AVR32 systems with an AC97C module.

	  Be aware that this will use channel B in the controller for
	  streaming data, this must not conflict with other AC97C drivers.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the module will
	  be called atmel-wm97xx.

config TOUCHSCREEN_WM97XX_MAINSTONE
	tristate "WM97xx Mainstone/Palm accelerated touch"
	depends on TOUCHSCREEN_WM97XX && ARCH_PXA
	help
	  Say Y here for support for streaming mode with WM97xx touchscreens
	  on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called mainstone-wm97xx.

config TOUCHSCREEN_WM97XX_ZYLONITE
	tristate "Zylonite accelerated touch"
	depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
	select TOUCHSCREEN_WM9713
	help
	  Say Y here for support for streaming mode with the touchscreen
	  on Zylonite systems.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called zylonite-wm97xx.

config TOUCHSCREEN_USB_COMPOSITE
	tristate "USB Touchscreen Driver"
	depends on USB_ARCH_HAS_HCD
	select USB
	help
	  USB Touchscreen driver for:
	  - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
	  - PanJit TouchSet USB
	  - 3M MicroTouch USB (EX II series)
	  - ITM
	  - some other eTurboTouch
	  - Gunze AHL61
	  - DMC TSC-10/25
	  - IRTOUCHSYSTEMS/UNITOP
	  - IdealTEK URTC1000
	  - GoTop Super_Q2/GogoPen/PenPower tablets
	  - JASTEC USB Touch Controller/DigiTech DTR-02U
	  - Zytronic controllers

	  Have a look at <http://linux.chapter7.ch/touchkit/> for
	  a usage description and the required user-space stuff.

	  To compile this driver as a module, choose M here: the
	  module will be called usbtouchscreen.

config TOUCHSCREEN_MC13783
	tristate "Freescale MC13783 touchscreen input driver"
	depends on MFD_MC13783
	help
	  Say Y here if you have an Freescale MC13783 PMIC on your
	  board and want to use its touchscreen

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called mc13783_ts.

config TOUCHSCREEN_USB_EGALAX
	default y
	bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_PANJIT
	default y
	bool "PanJit device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_3M
	default y
	bool "3M/Microtouch EX II series device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_ITM
	default y
	bool "ITM device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_ETURBO
	default y
	bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_GUNZE
	default y
	bool "Gunze AHL61 device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_DMC_TSC10
	default y
	bool "DMC TSC-10/25 device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_IRTOUCH
	default y
	bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_IDEALTEK
	default y
	bool "IdealTEK URTC1000 device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_GENERAL_TOUCH
	default y
	bool "GeneralTouch Touchscreen device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_GOTOP
	default y
	bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_JASTEC
	default y
	bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_E2I
	default y
	bool "e2i Touchscreen controller (e.g. from Mimo 740)"
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_ZYTRONIC
	default y
	bool "Zytronic controller" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_USB_ETT_TC5UH
	default y
	bool "ET&T TC5UH touchscreen controler support" if EMBEDDED
	depends on TOUCHSCREEN_USB_COMPOSITE

config TOUCHSCREEN_TOUCHIT213
	tristate "Sahara TouchIT-213 touchscreen"
	select SERIO
	help
	  Say Y here if you have a Sahara TouchIT-213 Tablet PC.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called touchit213.

config TOUCHSCREEN_TSC2007
	tristate "TSC2007 based touchscreens"
	depends on I2C
	help
	  Say Y here if you have a TSC2007 based touchscreen.

	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called tsc2007.

config TOUCHSCREEN_W90X900
	tristate "W90P910 touchscreen driver"
	depends on HAVE_CLK
	help
	  Say Y here if you have a W90P910 based touchscreen.

	  To compile this driver as a module, choose M here: the
	  module will be called w90p910_ts.

config TOUCHSCREEN_PCAP
	tristate "Motorola PCAP touchscreen"
	depends on EZX_PCAP
	help
	  Say Y here if you have a Motorola EZX telephone and
	  want to enable support for the built-in touchscreen.

	  To compile this driver as a module, choose M here: the
	  module will be called pcap_ts.
endif